Sorted:
  • EZlap Timing System

    X-Racer X-1 Racing with EZlap Timing System The EZlap timing system is a race management system that specially designed for both indoor and outdoor small scale drone racing. This new FPV race tracker allows 4 pilots to race at once. The EZlap timing system comes with a master controller, 3 infrared receiver modules, 8 transmitters. The system is powered by a PC or laptop via a USB cable connecting to the USB port of master controller. It is easy to install, simply mount the master controller and receiver modules in the racing gate, install the transmitters in the racing drones, then install the free RCM Beginner software (can be downloaded at the bottom of this page) in your computer and connect with the provided USB cable, you and your friends will be able to start the racing just in a minute.The master controller sends the signals that received from the infrared receiver modules to the computer after processing.The infrared transmitter is 0.4g only, it will not increase any weight to the racing drone since it is so light in weight. It has 8 different address codes which are switchable via the 3-digit DIP switch. Start to send the address codes after powering on via USB.The infrared receiver modules receive the address codes from the transmitters and send them to master controller.Connection and Use:The master controller is powered by the USB after connecting to the PC. No extra power supplies required.The receiver modules and master controller are connected with three special made 6-pin plug cables. In the EZlap timing kit there are 4 receiver modules (including the master controller) included. But how many modules you need depending on your track width and the height of your bridge. The quantity of receiver modules is also limited by the USB loading capacity.The infrared transmitter is powered by the built-in button cell battery.Connect the master controller to the PC with the provided USB cable, access to the free RCM Beginners software and set the pilots information.Package Inlcuded:Master controller x 1 (similar to receiver module but with a USB port)Receiver module x 3 Transmitter for racing quad x 816cm 6-pin plug camble x 33m long USB cable x 1Downloads:RCM Beginners (Free Software)RCM Beginners User ManualThe master controller is powered by the USB after connecting to the PC. No extra power supplies required. It sends the signals that received from the receiver modules to the RCM Beginners software after processing.The receiver modules are connected by 6-pin plug cables. They receive the address codes from the transmitters and send them to master controller.The infrared transmitter is 0.4g only, it will not increase any weight to the racing quad since it is so light in weight . It has 8 different address codes which are switchable via the 3-digit DIP switch. Start to send the address codes after powering on via USB.Three 16cm 6-pin plug cables are included to connect the receiver modules and master controller.The 3m USB cable is used for connecting the master controller to the PC. All the parts included in the EZlap timing system.Management interface of RCM Beginners.The EZlap timing system is working during the racing.

    Review: Write a Review

    $139.00

    SKU:FCTR

    Weight: 0.25 kg

  • TS100 65W Digital OLED Programmable Soldering Iron Station B2 Kit

    TS100 mini iron station is an internal heating intelligent CNC soldering iron, lightweight design, easy to assemble or disassemble and storage, comfortable handle, highly effective heating element and simple control interface, is indispensable tools for electronic worker !~Work between DC12-24V, with OLED screen, temperature adjustment buttons, external power independently, up to 300 ℃ just need as low as 10 sec. Features: * Based on 304 stainless steel nested polycarbonate housing, integration of safety circuit design power supply interface, anti-static structure, embedded STM32 processor chip, dual temperature sensor and acceleration extreme cooperate, TS100 intelligent temperature control between 100-400 degrees, instantaneous heating, automatic dormancy, overtemperature alarm, and other functions.* External independent power supply : DC5525 power interface, suitable for notebook DC12-24V power supply, car power and mobile power supply.* Micro USB interface: Through edit the parameter file, custom your own temperature curve and buttons function.* Additional features: Open source for writting your own App.

    Review: Write a Review

    $51.00

    SKU:TS100

    Weight: 0.30 kg

  • E-Design ES120 Motion Control Screwdriver (Pearl)

    E-Design ES120 Motion ScrewdriverUpdate on May 31st. : At fpvmodel.com, we include 9 different screwdriver bits with this motion screwdriver to meet your special needs, while other sellers include two only. The same price, but more screwdriver bits. Your satisfactory is always our top priority.★The best smart electric screwdirver on the market!★★2017 New Intelligent Electric Screwdriver!★Designed by the same manufacturer of TS100!Built-in STM32 Chip!User can customized configuration parameters!A new must on your workbench!Designed by the same manufacturer of the hot selling TS100, the ES120 Mini Electric Screwdriver has set a new standard for electric screwdrivers. It is an electric screwdriver with a compact structure, smart and exquisite appearance, as well as the function of motion control recognition. The ES120 has only the length of a Parker pen, while endowed with a comfortable design for holding, and a set of highly energy-efficient accessories. Through an OLED screen, the device displays parameters and rotation modes of motion-control recognition. Under these help, you are able to easily complete the disassembling and assembling of your digital devices. ES120 includes a planetary gearbox and a high-speed electric motor, with excellent support from the STM32 embedded micro-processor and angular velocity sensor. It operates at a voltage range of DC3V to 5V, and with various hexagonal screwdriver bits, the device helps you with fast disengaging and engaging of electronic products. Performance ParametersOperation Voltage 3-5VNo-load Speed About 170rpmElectronic Torque 2.5kgf.cmMaximum Torque 30kgf.cm (manual mode)Screwdriver Bit: 4mm hexagonCharging Time 45minRunning Time 30min (full power)Charging Mode Micro USB 5V InputHardware ParametersBody Material:  304 Stainless steel/Copper alloyScreen: 16*96 OLEDBattery:  300mAh 10440 Lithium-ion batteryLengh: 131mmWeight: 114g (Pearl)Rotor Bidirectional overrunning clutchGearbox 1:144 Integrated planetary gearboxMotor 25,000 rpm brush motorMain Chip STM32Sensor Angular velocity sensorSmart Functions1.Battery low voltage reminder, low voltage protection mode; 2.User ustomized configuration parameters (such as torsion, torque, etc); 3.Open source application layer.Package Including:1 x Motion Control Electric Screwdriver9 x Bit with different heads (Only at fpvmodel.com)1 x Bag1 x Manual

    Review: Write a Review

    $103.00 $94.76, Save 8% OFF

    SKU:ES120

    Weight: 0.45 kg

  • USB Linker For ESC Programmer Update SimonK ESC BLHeli Firmware

    Compatible with SIMONK and BLHELI ESCs, BLHeli Bootloader Or SimonK BootLoader, Atmel or SiLabs chips! (with or without Bootloader), supports ISP and C2 mode. This allows you to change the Bootloader, flash new Firmware normally, change settings or fix then the Bootloader as not been installed. It is the ultimate Multi-functional esc tool. - Direct plug design, works with most USB port and USB extension cable- Low power consumption design- On board 2x3 Pin AVR ISP port- 3pin servo connector, can be used as servo or C2 connection- Supports SIMONK and BLHELI ESC, KKflashtool compatible - KKflashtool and RapidFlash compatible- Silabs CP2102 Driver chip! (Win,Mac,linux)- Software upgrade-able (via Arduino or BLHELISUIT)- Pre-load as BLHELISUIT 4w-if 14.1 firmware

    Review: Write a Review

    $4.99

    SKU:ESCLK

    Weight: 0.10 kg

  • Orignal Amass XT30 Plug Connectors Male/Female One Pair

    Specification:Brand Name: AmassItem Name: XT30Quantity: 1 male & 1 femaleBody Material: Copper and gold platedInternal Material: Nylon/PAMax. RC/MC: 20A/30ATemperature Resistance: -20°C ~ 120°CConnector: 2mm Bullet TypeWeight: 1.8g/PairWire: 16-20AWGIncludes:Pair Amass XT30 Connector Male & Female

    Review: Write a Review

    $0.89

    SKU:AMSXT30P

    Weight: 0.10 kg

  • Matek FC Vibration Damping M3 Standoff

    Matek M3 vibration damping standoffs help to reduce vibrations on your camera or flight controller.Includes:- 4pcs M3*7*4.5 mm Rubber Vibration Damping Standoffs

    Review: Write a Review

    $2.79

    SKU:MKVDS

    Weight: 0.10 kg

  • Replacement Kit of Frame, Cover, Props and Motors for X-Racer X-1

    This is the accessories package for X-Racer X-1 and DIY purpose.  Including the cover, frame, props and motors.

    Review: Write a Review

    $15.99

    SKU:X1FC4

    Weight: 0.25 kg

  • New Multi-functional FPVmodel Motor Grip Pliers For RC Models

    Welcome to a world where changing props is not longer a painstaking difficulty, these are the newest version of Motor grip pliers from FPVMODEL. These light weight aluminum pliers may look simple but they are quite deceptive and feature a wide array of uses. These pliers are designed with a rubber strap to protect the beauty of your expensive motors while gripping the bell tightly to allow for quick and efficient prop nut removal. Say good bye to propellers biting into your hands while trying to hold the bell and prop while removing the prop nut...these pliers hold it for you. Ever had a hard to remove lens cap on your FPV camera? The end of the pliers offer another set of teeth in the end of one handle that is design to grip the lens cap housing and allow for simple removal.  FPVMODEL motor grip pliers also feature a built in wrench made especially for antenna removal. If your switches on your transmitter become loose in the field, no worries, these pliers have an adapter on the end made just for tightening your transmitter switches and keeping up with quick and simple maintenance. Overall, this simple yet effective tool is designed for a wide array of uses and can help eliminate several tools in your flight pack just by having this multi use tool at your disposal. These pliers are compatible with a variety of motors...2204,2205,2206,2207,1306,1406,and 1806. So as you can see your most commonly used motors in FPV are covered by this one multi-use design. Specs:Item Name: Motor Grip PliersMaximum opening: 45mmWeight: 57gPackage Included:1 Motor Grip Pliers2 sets of rubber tape

    Review: Write a Review

    $18.99

    SKU:FMPCU

    Weight: 0.20 kg

  • FATSHARK FACEPLATE FOAM SET (VELCRO)

    A replacement package containing two foam faceplates, and a velcro attachement pad suited for use with all faceplate equipped Fat Shark FPV Goggles.Removable velcro style. Kit comes with velcro adhesive backed strip, thick foam and thin foam. 

    Review: Write a Review

    $5.99 $4.97, Save 17% OFF

    SKU:FSV2628

    Weight: 0.10 kg

  • FatShark FSV1814 18650 Li-Ion Cell Goggle Headset Battery Case

    The Fatshark 18650 Li-Ion cell headset battery case is a way of holding 2 18650 batteries (* Battery NOT included) to provide a 7.4V nominal voltage for use with existing FatShark goggles. Case will fit into the standard head strap like the standard FatShark battery packs. This allows you to have a large battery capacity when used with high capacity cells (batteries not included). Batteries should be removed and charged via a dedicated 18650 style charger.

    Review: Write a Review

    $15.99

    SKU:FSV1814

    Weight: 0.15 kg

  • Dragonfly Transmitting SMA Female Antenna Extension Cables

    Dragonfly Transmitting SMA Female Antenna Extension Cables. A simple extension cable for better placement of your antenna.Specifications:- Connector: SMA Female- Cable Length: 45mm (cable only)

    Review: Write a Review

    $2.39

    SKU:DFTE

    Weight: 0.10 kg

  • Plastic FPV Protection Kit for Mini Racing Quadcopters

    Here comes a plastic FPV protection kit that specially designed for mini racing quadcopters like the ZMR210R, ZMR-X210 and KL200Race. The protection kit includes a plastic molded GoPro mount, a battery skateplate and four motor screw bumpers.Package Included:1.  Plastic molded mount for GoPro x12.  Plastic molded battery skateplate x13.  Plastic motor screws bumpers x4

    Review: Write a Review

    $13.99 $9.09, Save 35% OFF

    SKU:PMBGC

    Weight: 0.10 kg




Find us on Google+ Watch us on Youtube Like us on Twitter Follow us on Facebook

Home   |   New Products   |   About Us   |   Multi-Rotors   |   Contact Us   |   Blog   |   FPV Airplanes   |   FPV Equipment   |   Battery / Chargers   |   Tools & Accessories   |  Site Map

Product Tags: ABCDEFGHIJKLMNOPQRSTUVWXYZ0-9

Copyright © 2015 FPVMODEL.COM®. All Rights Reserved.