• Matek FCHUB-6S W/ CURRENT SENSOR 184A BEC 5V & 10V

    The Matek FCHUB-6S PDB distributes power from a 3~6S LiPo pack to 4 ESCs, as well as providing regulated & filtered DC 5V & DC 10V outputs for powering Cameras, RC receiver, Flight Controllers, Video Transmitters, LEDs, etc. It also has built-in 184A current Sensor, and offers a FFC socket to connect the MATEKSYS Flight Controller conveniently.Features:Total 4 pairs ESC solder tabs are fit for X type frameMax.27V input w/ TVS protectionBuilt-in current sensor 184APDB: 4*30A (4*46A, 5 seconds), 4layers*2oz copper PCBBEC 5V/1.5A(2A Max) w/ 100uF panasonic POSCAP filterBEC 10V/1.5A(2A Max.) w/ 47uF TDK MLCC filter5V & 10V Output LED indicators & Short circuit tolerant

    $9.60 $7.10, Save 26% OFF


    Weight: 0.10 kg

  • Replacement Kit of Frame, Cover, Props and Motors for X-Racer X-1 V2

    This is the accessories package for X-Racer X-1 V2 and DIY purpose.  Including the cover, frame, props and motors.

    $15.99 $10.23, Save 36% OFF


    Weight: 0.25 kg

  • Dragonfly Transmitting SMA Female Antenna Extension Cables

    Dragonfly Transmitting SMA Female Antenna Extension Cables. A simple extension cable for better placement of your antenna.Specifications:- Connector: SMA Female- Cable Length: 45mm (cable only)

    $2.39 $1.20, Save 50% OFF


    Weight: 0.10 kg

  • MATEK Lost Model Beeper & FPV FC 5V Loud Buzzer

    MATEK Lost Model Beeper & FPV FC 5V Loud Buzzer can be used on triditional PWM receivers or FPV racing flight controller.The tiny buzzer is drived by on board MCU. It can output louder sound than 5V active buzzers.Features & Spec.:- Built-in MCU- Working voltage range: 4.5~5.2V DC- Power: 1W Max.- Sound Output: 90dB Max.- Size & Weight: 18x13x8mm, 2g



    Weight: 0.10 kg

  • Stainless Steel RC Screw Kit, 720pcs/Kit

    This 304 stainless steel screw assortment kit help solve your repair, maintenance and model-making challenges. They provide a wide variety of sizes to minimize equipment down-time. This box contains the most often needed screws for your multirotor build. No more bent, rusted or corroded screws, our kits are made with the best 304 stainless steel money can buy.Features:1. Environmental Friendly2. Corrosion Resistant3. Anti-oxidation & Never rusted4. High Strength & HardnessContents:Round Head Screws ( 360pcs )50pcs – M3 x 12    60pcs – M3 x 1070pcs – M3 x 8      80pcs – M3 x 6 100pcs – M3 x 4 Flat Head Screws ( 360pcs )50pcs – M3 x 12    60pcs – M3 x 1070pcs – M3 x 8      80pcs – M3 x 6 100pcs – M3 x 4  

    $20.99 $18.47, Save 12% OFF


    Weight: 0.70 kg

  • Multi Color 6061 Aluminum Alloy M3*35mm Knurled standoff 10pcs

    Specification:- Size: M3*35- Color: Optional- Material: 6061 aluminum alloy- Pack: 10pcs- Weight: 12g ( 10pcs )Features:Much lighter but stronger and more durable. Multiple colors available for your choice. Please take note that due to the hardness, please do not lock the nuts forcibly. 6061 Alloy main alloying elements are magnesium and silicon to form Mg2Si phase. Fadeless and anti-static electricity.GB/ pass RoHS Surface treatment : AnodizingNote: The different batches may have a slight color difference.

    $6.99 $2.94, Save 58% OFF 1


    Weight: 0.10 kg

  • Multi Color 7075 Aluminum Alloy M3*6 Hex Screws 10pcs

    Specification:- Size: M3*6- Color: Optional- Material: 7075 aluminum alloy- Pack: 10pcs- Weight: 2g ( 10pcs )Features: Much lighter but stronger and more durable. Multiple colors available for your choice. Please take note that due to the hardness, please do not lock the nuts forcibly. Note: The different batches may have a slight color difference.

    $7.69 $3.08, Save 60% OFF


    Weight: 0.10 kg

  • FPV Model Sports Cap

    Show your brand pride all over town with this stylish hat from FPV Model. These are the FPV Model snap-fit caps specially designed for you. Made in a very reputable factory with only the highest quality materials. One size fits all. Two styles available with adjustable sizes. One is with strapback, the other is with snapback. If you are planning to go out for an outdoor event, these FPV Model Sports Hats are the best choice for you.Style A: FPV Model Strapback CapStyle B: FPV Model Snapback Cap 

    $9.99 $7.19, Save 28% OFF


    Weight: 0.20 kg

  • Skyzone 3D FPV Goggles Face Plate Goggles Parts

    Skyzone with Face PlateWe now have face plate for SKYZONE 3D FPV Goggles. It is suit for the former V1 to V3 goggles both white and black. For  V1,V2 and V3 can be upgraded to V4 (not including software). Besides, we have cancelled the F2D model, and changed it over to search frequency automatically.Under the 2d model, enter or exit by long pressing CAMERA, and it begins to search frequency by short press. Features:3D (Need to match with 3D Camera and Dual Transmitters, package not included)Complete plug and play kitDVR built in with playbackBuilt-in 40CH 5.8G Diversity that is compatible with most FPV 5.8G transmitters on the market (Fatshark,DJI,Walkra,Boscam etc)Built-in self-calibrating head tracking (gyro, inertial and compass)Built in Dual 854X480(WVGA) Monitors, 1,229,760 color sub-pixelsBuilt-in external camera for surrounding view (640X480)AV in/ AV out/ Earphone socket (with volume control)Adjustable Interpupillary and Diopter for your eyesAdjustable brightness and contrastHeadband Plastic EyepatchSponge Mat

    $19.99 $10.39, Save 48% OFF


    Weight: 0.20 kg

  • $8.99 $3.33, Save 63% OFF


    Weight: 0.10 kg

  • $8.99 $4.94, Save 45% OFF


    Weight: 0.20 kg

  • FatShark Replacement Head Strap

    Head Strap for replacing your worn out, tired and smelly old head strap.Color: Black/ Blue / Grey (optional)Material: Nylon

    $5.90 $4.96, Save 16% OFF


    Weight: 0.10 kg

  • HENGE 5v/6v/7.4v 8A UBEC 7V-25.5V Input 2-6 Lipo

    HENGE 8A UBEC is an external voltage stabilizer, it works at the Switch Mode. It can obtain the suitable DC voltage from 7‐25.5V input voltage for receivers and other device, and steadily provide 8A current to supply power for receiver, gyro, and multi servos. Therefore, the 8A UBEC is very suitable for large electric fixed wing aircraft and helicopters which uses 4S or more batteries. With this UBEC, you can obtain the power for receivers from dynamic power without equipping independent battery pack for receivers.Specifications:- Output voltage: 5V/8A , 6V/8A or 7.4V/8A(changeable with a jumper),Maximum output current: 12A(≤15S)- Input voltage: 7‐25.5V (2—6 cells Lipo battery pack or 6—16 cells NIMH battery pack)- Ripple: <35mVp‐p (@8A/12V)- Size: 45mm*22mm*7.5mm (L*W*H)- Weight: 16gFeatures: 1. Designed with an advanced switching power supply control chip with overcurrent and overheat protection function, the max efficiency of the chip is up to 93%;2. The small size and the light weight make it very convenient to use;3. Provide large output current, the continuous output current is 8A, and the burst output current is 12A, fully guarantee the power demand of equipment.;4. Designed with a high quality switching power supply conversion chip, significantly reduce the electromagnetic interference and ensure the receiver works properly;5. With ultra‐wide input voltage from 7V—25.5V (2—6 cells Lipo battery pack or 6—16 cells NIMH battery pack).

    $15.99 $11.19, Save 30% OFF


    Weight: 0.10 kg

  • Replacement Standoffs 35mm for Multirotors 10pcs

    Show your own personality, these are replacement standoffs for mini multirotors, like ZMR180 and ZMR250 V2. They will give your multirotor individuality and style. 10pcs per set, available in black, blue, silver and yellow (optional).Specifications:Material: Aluminum alloyInner thread M3Length: 35mmOuter Diameter: 5mmColor: Black/Blue/Silver/Yellow/Red (optional)Quantity: 10pcs/set* The frame kit is not included.

    $5.80 $1.99, Save $3.81 OFF


    Weight: 0.10 kg

  • Multicopter LED Brake Light Stop Light Board For QAV250 FPV

    Braking RGB lights for multi-rotorsDescription:Item Name: Braking RGB Lights Board / Stop Light Board Board Size: 60 x 12mmWeight: 2.6g (Without cables) Features:The multicopter brake light makes flight status of aircraft just like car taillight visual display. Simple installation, the real-time image across the back can quickly judge the flight status in front of the aircraft. Note:Forward Flying–The tail light shows greenStop Flying–The tail light shows redBackward Flying–The tail light shows white Package Included:1 x Stop light board 1 X Y cable1 X Extension Y cable1 X Double-sided adhesive

    $5.39 $1.51, Save 72% OFF


    Weight: 0.05 kg

  • Matek WS2812B RGB 5050 LED Board for FPV RC Multicopter

    Specifications:- Power supply voltage: +3.5~+5.3 V- Input voltage: -0.5~+0.5 V- Operation junction temperature:-25~+80 ℃- Storage temperature range:-55~+150 ℃- Can be used for NAZE 32- Size: 51mm*10mmApplications- Naze 32 LED Strip with CleanFlight, AVR, Arduino, PIC, mbed, etcNote : only the LED board

    $4.90 $3.43, Save 30% OFF


    Weight: 0.05 kg

  • Futaba adapter cable with a square Micro-pin buddy port

    Futaba adapter cable with a square Micro-pin buddy port220mm Long

    $7.39 $3.70, Save 50% OFF


    Weight: 0.12 kg

  • 11 inch Articulating Friction Magic Arm + Super Clamp for DSLR Camera /LCD / LED Light

    This is a professional 11 inch articulating arm made of alloy metal.The magic arm extends small devices, like LCD monitors or LED light, from your video rig setup or camera. It is especially useful in fixing your LED light away from the camera super clamp to prevent hard light.The magic arm is composed of joints: the central joint is horizontally adjustable in 360 degrees while the side joints have mini-ball heads that are adjustable in 105 degrees. All three joints are locked by the central locking wheel securely and easily.Description:It is versatile for HDV HDSLR film makers,especially for Follow focus users when taking photo or video, it can be used to mount LED light,flash or LCD Monitor on to your DSLR cage,HDSLR camera, clamp or shoulder mount rig.It is 11 inches in length when fully extended.Large center locking knob to lock all movements , Variable friction and positionLoad: up to 2kg1/4" screw adapter to fit lightstand, small flash, LED light & other accessories with 1/4" female / male screw sockets.Ideal gear for mounting accessories exactly at any angle you need.Package includes:11 inch Magic Arm  x 1Super Clamp  x 1

    $21.99 $11.87, Save 46% OFF


    Weight: 0.70 kg

  • VHB 3M Super Strong Ultrathin Double Sided Adhesive Tape Traceless Waterproof 2pcs

    VHB High density and strong tack 3M double sided foam sponge adhesive tape.Ultrathin size but with super strong holding power.Traceless and Waterproof,you will no need worry about the ugly left on you lovely plane.This is a good  assistant for your plane building work.High heat resistance:the anti-heat temp up to 70° .Size:84x53x0.64mmQuantity:2 pcs

    $4.90 $3.14, Save 36% OFF


    Weight: 0.05 kg

  • Prop Adapter for Dragonfly 1806 Motor CW/CCW

    Prop adapter for Dragonfly 1806 motor,A replacement for the 1806 motor,if yours lost or broken,you can buy it from here.CW or CCW thread,choose which you need.Note:This prop adapter also compatible with FPVMODEL 1806 2300KV motor or Dragonfly and FPVMODEL 2204/2206 motors.

    $3.00 $0.84, Save 72% OFF


    Weight: 0.05 kg

Find us on Google+ Watch us on Youtube Like us on Twitter Follow us on Facebook

Home   |   About Us   |   New Products   |   Multi-Rotors   |   FPV Airplanes   |   FPV Equipment   |   Battery / Chargers   |   Tools & Accessories   |   Contact Us   |   Blog   |  Site Map


Copyright © 2015 FPVMODEL.COM®. All Rights Reserved.