• Micro MinimOSD w/ KV Team MOD

    The MinimOSD was engineered to bring users a very powerfull OSD. It’s a nice and tiny board perfect for mini quads. With all the features of the very popular minimosd KV Team modded OSD but in a tiny 15x15mm size.Apart from the size, the only differenece is that it does NOT have the DC/DC converter - this means less heat when powered off a flight controller. The micro MinimOSD has been modified to take advantage of custom firmware options. You can flash firmware that is MAVLink compatible for ArduCopter, or MultiWii Serial compatible for MultiWii and Baseflight/Cleanflight control boards. You can connect two batteries up to 4S so you can see the main flight battery voltage.  The second port will allow a separate FPV battery voltage on the display as well. There is also a pin for analog or digital PWM RSSI and a connection where you can attach a current sensor.Features:- All the same features as the orgnal, but less the half the size - NO Dc/Dc convert . power board via 5 volts - FTDI cable compatible pinout- Standard 6-pin ISP header- Two LED indicators- ATmega328P with Arduino bootloader- MAX7456 monochrome on-screen display- 15x15MM Size!- Modifications for direct connection of two batteries (up to 4S)- Pad for an Analog or Digital PWM RSSI signal - Pad for the connection of a Current Sensor- ATmega328P with Arduino bootloader- Standalone, or with APM/ Flip / Flip32+ flight controllers - These modifications allow direct connection of two batteries (up to 4S)SpecificationsATmega328P with Arduino bootloaderMAX7456 monochrome on-screen displayFTDI cable compatible pinoutStandard 6-pin ISP headerTwo independent power sections with an LED indicator on eachSolder jumpers for combining the power sections+5V 500mA regulator for up to +12V supply inputSolder jumper for PAL video optionExposed test points for HSYNC and LOSDimensions: 0.7"W x 1.7"L (2.4" w/ pins as shown) x 0.3"H

    $12.95 $7.51, Save 42% OFF


    Weight: 0.10 kg

  • FEIYU FY 41AP Lite Autopilot AFSS&OSD For Fixed Wing

    FY-41AP Lite is an inertial attitude measurement instrument used for FPV flight on fixed-wing aircrafts. It has an integrated OSD video overlay system that presents critical flight information such as power management, airspeed, altitude, and flight direction via its electronic compass, allowing for a clear visual flight while ensuring key information is within sight.Flight stabilization is achieved via an integrated 3 axis gyro, 3 axis accelerometer and a barometric pressure sensor. This enables the module to accurately measure flight attitude, earth azimuth & relative altitude to achieve:- Extremely stable conventional flight pattern- Stabilized 3D flight- Automatically return to home (RTL)- Fixed altitude flight- Heading lock flight- Auto circling over a fixed GPS location. Function Introduction● Deactivated Mode —— In this mode, the FY-41AP Lite auto stabilization is turned off. The aircraft is completely under pilot control.● Stabilized Mode —— Level flight is automatically maintained, making flight simple, especially for beginners. If a pilot feels the plane is out of control, simply reduce input control and the plane will automatically recover level flight.● 3D Mode —— If no input is given by the pilot (all sticks in the middle position), 3D mode will lock the current aircraft attitude. Therefore the aircraft can be easily maneuvered to complete a variety of 3D flight with added stability & smoothness.● Fixed altitude & Heading lock Mode —— This mode maintains aircraft flight course & holds the altitude on activation. By using GPS data, the system automatically corrects flight course deviation & maintains straight-line flight.● Auto Return To Launch Mode (RTL) —— Upon activation of this Mode, the aircraft will automatically return to the Home point, maintaining its current altitude. Upon reaching the Home point, it will initiate auto circling.> Related download :FY-41AP Lite Manual :  DownloadFeiyu tech kindly remind you: You should to do the firmware upgrade separately for FY-41AP Lite control module and OSD module . UART1 is the interface connects to the data radio, computer serial port to do the firmware upgrade for FY-41AP Lite control module.If you want to upgrade the firmware of FY-41AP Lite OSD module,please click on hereOSD Video Overlay System Function● First Person View (FPV) —— FY-41AP Lite has an integrated OSD video overlay system that presents critical flight information on the video for easy enjoy FPV, at the same time, Auto stable, Fixed altitude & Heading lock, Auto Return To Home function will make FPV operation more easy.OSD is an essential part for FPV. The FY-41AP Lite can adapt both PAL and NTSC video signals. The entire adaptive process is completed approximately within 1 second.Integrated OSD Video Overlay System, FY-41AP Lite overlays flight telemetry information onto video image. Information displayed includes: Altitude, Speed, Direction, Home Direction and many more. FY-41AP Lite OSD display part firmware V1.22 : DownloadFY module firmware upgrade software and manual :Download You should to do the firmware upgrade separately for FY-41AP Lite control module and OSD module. UART2 is the interface connects to the computer serial port to do the firmware upgrade for FY-41AP Lite OSD module.If you want to upgrade the firmware of  flight control part ,please click on hereFY-41AP Lite Compared With FY-41AP Basic PerformanceSupported aircraft:1, Normal / Traditional fixed-wing planes;2, Delta-winged plane with rudder;3, Delta-winged plane without rudder;4, V-tail plane with aileron;5, V-tail plane without aileron;Supported servo output :   50Hz refresh frequencyRecommended Transmitter :   PCM or 2.4GHz with minimum 6 channelsFY-41AP Lite Module Working Voltage :   5.3V@0.2A( Powered by Power Manager)Air speed senor :   0 ~ 200KM/hPower Manager :   35g(50×24×18mm)Working Voltage Range :   Power of battery 7~26V (2S ~ 6S)Measuring current :   0~100APower for FY-41AP Lite module :   5.3V@2APower for Video transmission system :   12V@2AOperating Temperature :   -10°C ~ 50°CAssistant Software System Requirement :   Windows XP sp3 / Windows 7 / Windows 8  HardwareFY-41AP Lite: 20g (61×39×14mm);GPS :24g (32×32×13.5mm);Air speed senor:9g (64×13.5×13.5mm);Power Manager:35g(50×24×18mm); GCS Ground Station Software GCS ground station software, used to set the flight parameters, mission planning, monitoring in flight. Software integration of electronic map function can through the map software the Google earth live map out into the GCS software. The main function is     Parameter Settings — Control parameters setting, course setting, etc.     Real time monitoring — It can monitor flight attitude. And via the GCS software you can change the flight altitude in real time and realize the mouse click flight.     Record and monitoring flight — You can monitor and download flight path via the GCS software in your computer.GCS 5.11 Software:  Download



    Weight: 0.50 kg

  • DJI IOSD mark 2 for DJI WKM ACE ONE Autopilot System

    DJI-IOSD-M2 DJI iOSD Mark II On Screen Display for DJI Wookong M WKM The iOSD Mark II On Screen Display is for the DJI Wookong M AutoPilot and Ace One series AutoPilots. The iOSD On Screen Display enables the pilot to monitor the real-time flight data from the Wookong M WKM  or Ace One Autopilot systems while in flight using First Person View (FPV).The DJI iOSD MARK II can record the flight log, which will help you to record the input and output information of every channel, GPS signal, power voltage, home distance and height, etc. (The current iOSD on the market will have flight log function after firmware upgrade.)The DJI iOSD will allow you to view the following information:Voltage.Vertical velocity.Horizontal velocity.Height.Distance from home point.Horizontal Altitude.GPS satellite number.The iOSD is a multifunctional integrated on screen display module which also has a built-in BEC module that supports 3s-6s LiPo batteries (11-26 volts), when used with the Wookong M or Ace One professional autopilot systems, it delivers a total solution for aerial photography with key information clearly displayed around the outside of the screen.The DJI Innovations iOSD only supports the Wookong M AutoPilot and Ace One systems at this time. The iOSD supports two video input sources, one of which can be selected by the R/C transmitter and switched remotely. It can also change the wireless the transmission channel using the wireless video transmission module by DJI. The iOSD can be upgrade in the future by firmware updates.PlatformSupport WooKong-M CurrentlySize52 mm x 41 mm x 11 mmWeight56gVideo Input/Output ModePAL/NTSCElectrical CharacteristicsVoltage:3S-6SCurrent(Typical Value):60mA@52.2V, 103mA@12.6VRated Power:1.25WOperating Temperature-20°C to +60°CFunctionsiOSD Information TransmissionVideo Transmission, Two Video Signal Channels Input & SwitchChannel Switch Supported for the Wireless Video Transmitter Module specified by DJIBuilt-in BEC, strengthened the drive system MC power supply reliabilityDJI Z15 Supported 

    $158.00 $59.90, Save $98.10 OFF


    Weight: 0.20 kg

  • Skylark AAT convert module for other brand OSDs

    Skylark AAT Auto Antenna Tracker Convert ModuleThe skylark AAT Tracker V4 could support the Skylark seious OSD by default, but if need to work with other OSD or flight controller, customers have to buy this convert module separately.Plug and play, small in size (1cm*3cm), weighs only 2g, perfectly compatible with Skylark Tiny OSDFeatures:Plug and play, self-adapting baud rate. Compatible with all the NEMA GPS.Compatible with most GPS and flight controller in the world.Has GPS data transfer fuction.



    Weight: 0.10 kg

Find us on Google+ Watch us on Youtube Like us on Twitter Follow us on Facebook

Home   |   About Us   |   New Products   |   Multi-Rotors   |   FPV Airplanes   |   FPV Equipment   |   Battery / Chargers   |   Tools & Accessories   |   Contact Us   |   Blog   |  Site Map


Copyright © 2015 FPVMODEL.COM®. All Rights Reserved.