Sorted:
  • KISS FC V2 - 32bit F7 Flight Controller

    *** FPV Model is an authourized dealer of FLYDUINO KISS. Genuine KISS flight controller guaranteed.Before Purchasing: Please keep the packaging after receiving KISS flight controller. Each genuine KISS FC has a unique serial number on the packaging, while fake KISS FC does not and can not be activated. Flyduino, the designer and manufacturer of Kiss FC, will offer the technical support only to the ones with serial numbers. If the packaging is lost, you may fail to get the technical support from Flyduino in time. Besides, for any return of KISS products, you will need to send back the KISS packaging as well.Finally Flyduino release the KISS V2 flight controller with a F7 processor. As an authourized dealer of Flyduino, FPV Model is one of the first to receive the FCs. A new simplified Flight controller, the KISS FC V2 includes a complete own Flight Control Firmware development. The Idea was to get the simple KISS FC to the next level and due to intensive long term tests of some pretty good Pilots we were able to optimize the code to a point where you hopefully get your quad in the air quite quick.Normally you just need to choose your Airframe in the GUI and you are able to fly (at least with KISS ESC), otherwise you can download presets of well known pilots for given configurations. And of course you can tweak the PID yourself through the GUI.The software setup side is reduced as far as we could, many things are already taken into account for you, if you have some solid soldering skills you should be able to build your quad pretty quick. A known feature is also the telemetry, in combination with our 32bit ESC line it‘s possible to show the live telemetry data via OSD on your FPV live feed or in the KISS FC GUI. This way you get useful informations like the Voltage of your battery, current consumption, ESC temperature and motor RPM. Other FC firmwares (eg. Betaflight) are ported for the use with the KISS FC V2.ARM-Cortex M7 MCUwith FPU @ 216Mhzfor even the most complex algorithms. up to 12 times faster now.Powered directly by the battery(2-6S) max. 500mA @ 5Vavoids unnecessary weight.Onboard USBCP2102 USB-UARTUSB controller for easy updates of FC and ESC directly via GUI.Bidirectional communicationultrafast Dshot 2400, sinHybrid and full Kiss Telemetry support.Serial Monster5 for all use cases.SpecificationsMCU: STM32F722RET6 @ 216 MHzIMU: MPU6000Weight: 5gMounting: 3x3cm  (mit 3,3mm L?chern)Voltage: 2-6S (direkt)Tri, Y4 and Y6 * Quad + / x * Hexa + / xThe needed USB driver will be installed when you connect the flight controller the first time. It could take several minutes till you can bind the flight controller to the GUI.Supported FrSky Sbus, Graupner SumD, TBS CROSSFIRE and Multiplex SRXL as S-Port, HOTT, TBS CROSSFIRE and Sensorbus.Turtle mode supported5x SerialRunCam Split supportedRGB Led supportedDShot 2400FW via GUIAdvanced adaptive FilterAdvanced Motor LayoutWindows, OSX, Android supportedWiring Diagram of Kiss FC V2- Click to enlarge.Flyduino KISS FC V2 Connection Plan by Philipp Seidel.  Click to enlarge

    $79.99 $65.59, Save 18% OFF

    SKU:KSFCV2

    Weight: 0.10 kg

  • BetaflightF4 Flight Controller

    BetaflightF4 How to ESC Telemetry, Smart Port Audio, Smart Port TelemetryFriendly Reminder: Upon receiving your FC, please connect to USB and calibrate before continuing to build and solder to it.  BetaflightF4 is the follow up design to the very popular BetaflightF3. Following in the same path as Betaflight F3 we have kept a very similar footprint in terms of design with a few added modifications. The F405 has replaced the F303 to allow for lower CPU loads.We have eliminated the 5v/3.3v jumper and added two seperate connection points, one for sbus and one for spektrum users. The jumper still remains for the battery voltage/5v connection for connecting your camera. While wiring the board it is recommended to get power for your vtx either from a different 5v source on the board or if using a higher voltage vtx power it from the battery input coming into the pdb. Running ground loop at Agnd with gnd wires from camera and vtx is still recommended to give the cleanest video signal. Another small design change to this board was changing the BEC, this change takes the recommended 5v 2A current limit and drops it down to 5V 1.5A, its a small change but one that we opted for in order to use a more reliable BEC.BetaflightF4 now comes with telemtry pads for BLHeli32 ESCs these pads are located between the signal and gnd pads for the ESC connections.FeaturesIntegrated PDBBuilt in OSD customizable via Betaflight OSDCurrent sensorIntuitive layoutFlash memory for blackboxTailored to support BetaflightWhen running 8K/8K, CPU usage remains lowSpecificationsF405 ProcessorMPU6000 Gyro/ACC SensorBEC Max current 5V 1.5ABuilt in OSD – configurable via Betaflight GUICurrent sensorPower distribution board with six-layer PCBOSD Max Current: 145AWiring Diagram - Click to enlarge!BetaflightF4 Connection Plan by Phillip SeidelBetaflightF4 Turtle Mode SettingBetaflightF4 OSD FlashingHow to Use ESC TelemetryBetaflightF4 Can not ArmHow to Use Smart Port TelemetryHow to Use BetaflightF4 IBUSThe Number of “Scale the Output Voltage to Miliamp” in BetaflightHow to Set Tramp HV VTXIf you are meeting a problem with the use of flight controller and can not find the answer, please submit your question.

    $44.73 $33.99, Save 24% OFF 3

    SKU:BFF4

    Weight: 0.10 kg

  • OMNIBUS AIO F7 V2 Flight Controller

    Features:- F7 MCU - faster than the current F3 and F4 processors- Two gyros on the flight controller: an MPU6000 for sampling up to 8khz and ICM20608 for sampling up to 32khz- Built in betaflight OSD- 36x36mm, mount holes 30.5x30.5mm- SD card reader for recording black box data (SD card not included)- Supports 2-4s natively, 5-6s with 220uf 35V capacitor- 5v/1A regulator- Port for easy connection to Airbot 4-in-1 esc (SH1.0 8P)

    $55.00 $48.40, Save 12% OFF

    SKU:OF7V2

    Weight: 0.10 kg

  • OMNIBUS F4 Pro Corner Flight Controller

    The Omnibus F4 Pro Corner flight controller uses the ICM20608 over SPI for the best possible flight performance. With onboard damping box, the ICM20608 runs perfect under 32k Gyro loop. If you havent already seen it, you should check out Joshs awesome video on different IMUs. Also onboard are a barometer and AB7456 OSD chip for the BetaFlight integrated OSD.Omnibus F4 Pro Corner supports 3-6s LIPO direct input, build in Current Sensor and Power Filter too.The on Board PDB is tweaked by using 12-Layer PCB design. There is only 0.2-0.5 mohm internal resistance from input to each output padsFeatures:- STM32 F405 MCU, Runs Betaflight firmware(supported from v3.2)- ICM20608 Over SPI Bus in damping box. (optional MPU6000)- 30.5x30.5mm Mounting holes- Supports Lipo direct plug in (3-6S)- Suports 5V 1A BEC output(Buck)- STM32 controls OSD chip over SPI in DMA mode(Betaflight OSD)- Build in Current sensor- Build in Professional level PDB- Build in LC filter for Camera power(max 800ma)

    $49.99

    SKU:CF4PC

    Weight: 0.10 kg

  • OMNIBUS F4 Nano v3 with LC filter

    - A new generation AIO Flight control for FPV, based on F405 MCU, using F4 MCU controls OSD over SPI bus in DMA mode, OSD Configation has been incl. in Betaflight GUI.- Supports SD Card and LIPO direct input (2-6S)- MPU6000 at SPI bus. No Flash for blackbox functionFeatures:STM32 F405 MCU, Runs Betaflight 3.2 firmwareSBUS/PPM input (Pinheaders)4PWM output (1-4Pinheaders and Sh1.0 Plug)Only 25x25mm, mount holes 20x20mmIncl. Barometer BMP280SPI Sensor MPU60002-6S Lipo Direct poweron board LC filterUpdate on August 14th: Add a connecting cable.

    $35.99 $29.51, Save 18% OFF

    SKU:OBF4V3

    Weight: 0.10 kg

  • RaceFlight Millivolt Flight Controller

    MillivoltThe RaceFlight Millivolt flight controller is the most advanced, performance driven, flight controller ever designed in a tiny package. Capable of running 32kHz gyro sample, PID loop, and motor loop, processing all calculations in real time. The Millivolt is truly at the top of its tiny class . The Millivolt uses a F405 MPU and an Invensense 20602 gyro in combination with RaceFlight software to give you the BEST performance possible. This gyro is by far the most noise free and accurate gyro available.PerformanceThe Millivolt presents not only the BEST performance, but also the most STABLE performance due to the amazing vibration rejection technology implemented in RaceFlight. Our filters allow your quad to stay in the air no matter what! Damaged propellers caused by that insane gate clip on turn 3? Not a problem. You can still finish the race! For most people tuning is not even required. Our boards come preloaded with software and defaults that should fly amazing for 99% of people.In addition to the vibration rejection technology, the SSG (Invensense 20602) gives you the highest speeds currently possible with the lowest noise floor and highest sensitivity. The Invensense 20602 gyro has never been used in any flight controller before (except the Revolt) and definitely gives you the leading advantage over others.SoftwareOur flight controller comes pre-loaded with the latest RaceFlight Community release. Just go to the google store and download the latest configurator and you should be ready to connect. Drivers should no longer be needed.RaceFlight One is also available in beta format. Just join our slack at https://raceflight.net/invite/ and ask to be added to the RaceFlight One channel. This is truly amazing software, which flies so well you can completely eliminate prop wash. Setup is a breeze as well, just run a couple wizards and you will get right up into the air.Setup SimplicitySetting up the Millivolt is easy. The solder pin layout is easy to read with motor connections in each corner. Just solder the closest motors and remember the order 1, 2, 3, 4. Select your voltage on the bottom, as well as inverted or not. The Millivolt also features DFU free updating and a self-healing and updating bootloader, just in case something does go wrong.FeaturesIntegrated vibration dampening dummiesInverter for Taranis and Futaba radios3.3v or 5.0v for Spektrum, Taranis, etcLED Driver for WS2812b programmable LEDInfrared LED Race Transponder support – just solder an infared LED to the Revolt and set it up in the RF1 configuratorFuture iPhone and Android configurator supportHigh Speed 32khz gyro, lowest noise floor and highest sensitivity gyro ever usedThrough hole solder pads – forms an I-Beam when soldered for extra strengthFrSky Taranis, Spektrum, Futaba, JR, IBus, Sbus and other radio supportIntegrated buzzer driverVoltage and current ADC pins, for full voltage and current monitoringFull telemetry output supportESC flashing and configuration built into configuratorMost active software developmentSelectable 3.3v or 5v voltage2 serial uartsBluetooth expandableF4 processor16mb of flash memoryGPS expandableDimensions: 25mm x 25mmMounting holes: 20mm squared to center of holes

    $41.88 $34.34, Save 18% OFF

    SKU:RFMFC

    Weight: 0.10 kg

  • Flycolor RAPTOR S-Tower 12A BLHeli-S 2-3S ESC with F3 Flight Controller Built-in OSD

    Specification:Brand name: FlycolorItem name: 12A BLHeli-S 2-3S ESC with F3 Flight ControllerFirmware: BLHeli-SContinuous Current: 12ABurst Current: 15AInput Voltage: 2 – 3SSize: 30.5*33.4*19mmBEC: 5V/1A (F.C)Weight: 11.5gFeature:- EFM8BB21F16G MCU with 50 MHz maximum operating frequency. using dedicated 3in1 drivers, makes the start more smooth. ESC maximum speed is limited to 500k eRPM.- Small size&lighter in weight. More suitable for ultra small multirotors.- Two layers tower structure between 4in1 ESC and FC using quick pin connection. makes the installation faster and more convenient- Exposed pads for Battery and Motor wires, fast welding without additional disassembly, motor replacement is more convenient .- F3 flight controller, supports PPM and SBUS remote control / receiving mode.- FC integrated OSD, no external OSD device is required, integrated 5V/1A for Image transmitter, camera, buzzer, LED and other peripheral devices ;- BLHeli-S firmware designed for superior performance in multirotors, and uses hardware generated motor pwm for smooth throttle response and silent operation.- There are tuneable parameters that can make the code run well even in the most demanding situations, although default settings will work excellently in normal operating environments.- The code supports regular 1-2ms pulse width input, as well as Oneshot125 , Oneshot42 and Multishot . The input signal is automatically detected by the ESC upon power up.- Supports Dshot digital signal, anti-interference ability is stronger, and do not need throttle calibration.

    $50.99

    SKU:FCRST

    Weight: 0.10 kg

  • BetaflightF3 Flight Controller

    BetaflightF3 Flight Controller | REVIEW AND HOW TO by Joshua BardwellBetaflightF3 is the flight controller designed to use every possible feature of Betaflight. More than the last half year has been spent in development. Boris B has worked with us to go over features and design aspects to help give us insight into what betaflight users want/need. This board features a 3A power draw giving users extra room for added attachments through uart ports. The six layer PCB is a more expensive design approach but was needed to give the ability to have a PDB that was capable of having wiring pads on both the top and bottom of the board. By using the six layer design we were able to increase the size of the pads and work around all the components all the while giving esc connections in the corners of the board rather than bunching all connections on either the top OR the bottom. Featuring a fully functioning OSD that can be configured in Betaflight this board will make configuring your OSD a breeze. The team at betaflight have been hard at work developing DSHOT and this board is also compatible with the latest release. But we didn’t stop there, this board also features a micro adapter to accept TF cards for those of you that like to follow up your flights with reviewing black box logging...we think we know of at least one guy that will like that. FeaturesIntegrated PDBBuilt in OSD customizable via Betaflight OSDCurrent sensorIntuitive layoutSD card slot for BlackBoxTailored to support BetaflightWhen running 8K/8K, CPU usage remains lowSpecificationsF3 ProcessorMPU6000 Gyro/ACC SensorBEC Max current 5V 2ABuilt in OSD – configurable via Betaflight GUISD Card adapter for BlackBoxCurrent sensorPower distribution board with six-layer PCBOSD Max Current: 145AWeights 8.6g***Note: Please do not connect to any equipment with the loading over 1.5A.Friendly Reminder: Choosing your power supply for video is relatively simple. Betaflight FC has two options, 5v and battery voltage. Choose your camera voltage by jumping RAM with either the 5V solder section or the Vbat solder section. (its recommended to use Vbat, Most cameras and Video transmitters can run off battery voltage) If using 5v it is recommeded to only power your camera and get the power for Vtx from another source. 

    $42.99 $29.66, Save 31% OFF 3

    SKU:BFF3

    Weight: 0.10 kg

  • KISS FC 32bit Flight Controller V1.03

    *** FPV Model is an authourized dealer of FLYDUINO KISS. Genuine KISS flight controller guaranteed.Flash Deal! Kiss Flight Controller for only $25.99 !!The sale is limited to 10 Qty Only. The price will get back to normal after 10 Qty sold out. Hurry before they are sold out!Before Purchasing: Please keep the packaging after receiving KISS flight controller. Each genuine KISS FC has a unique serial number on the packaging, while fake KISS FC does not and can not be activated. Flyduino, the designer and manufacturer of Kiss FC, will offer the technical support only to the ones with serial numbers. If the packaging is lost, you may fail to get the technical support from Flyduino in time. Besides, for any return of KISS products, you will need to send back the KISS packaging as well.- Changed bootloader solderpads to a press button- Changed USB Port typeAs we felt the need for a modern more simplified 32bit Flightcontroller, we made the KISS FC, which includes a complete own Flight Controll Firmware development who get rid of some old ballast, this took some time, but the result is very pleasing.The Idea was to simplify some things and due to intensive long term testings of some pretty good Pilots we where able to optimize the code to a point where you hopefully get your quad in the air quite quick.Normally you just need to choose your Airframe in the GUI and are able to fly (at least with KISS ESC), otherwise you can download presets of well knowen Pilots for given configurations and of course can tweak the PID yourself over the GUI.The software setup side is reduced as far we can, many things are allready taken in to account for you, if you bring some solid soldering skills you should be able to build your quad pretty quick.A new feature is also the inbuild telemetry, in combination with our 32bit ESC line its possible to show the live telemetry data via OSD on your FPV live feed or in the KISS FC GUI.?This way you get usefull informations like the Voltage of your battery, current consumption, ESC temperature and motor RPM.Supported copter types:- Tri- Quad +/x- Hexa +/xSupported RX types:- PPM Sum- Spektrum Sat. (serial / DSM2 & DSMX)- Futaba / Taranis SBUS- Jeti ExBus- Graupner SumD / SumO- MultiPlex- classic RX with single channel output- STM32F303CCT6- MPU6050Weight: 4.6gMounting Holes: 3x3cm pattern, with 3.2mm holes (widely compatible)Voltage: 2-6SDriver for STM32F303CCT6Normally you dont need to download any driver for the USB support.Windows 7 8 and 10 care for this on their own after you connected the device.The connection diagramm / Pinout you find in KISS-FC GUI.DOWNLOADS (Manuals, Firmware, GUIs): Click HereReview on KISS FC by Oscar Liang

    $39.99

    SKU:KSFC

    Weight: 0.10 kg

  • Tarot ZYX-M Flight Controller for multi-copter ZYX25

    Update on Dec. 3rd, 2015: Add the V1.01 upgrade to V1.04 manual.The revolutionary flight controllerWith multiple new technologies, Tarot ZYX-M simplifies all complicated operation and brings you easy and natural flight experiences.To upgrade the flight features, ZYX-M is equipped with smart computing and navigation control systems. Pilots can adjust tilt, roll, and pan axis through setup software according to different preferences.Furthermore, it supports fail safe and voice alarm, including range setting and no-fly zone alarm. ZYX-M keeps the multi-copter under control during flights. Main controller:32 bit processorBuilt-in anti-vibration sensorFull metal caseSupports dual S-BUS receiverSupports dual DSM satellite receiverSpecific Interface for TAROT gimbal controlGPS module:Highly efficient GPS receiverHigh gain antennaFast and accurate locatingPMU module:Dual power outputSupports power output to flight controller, gimbal, and video TX in the same timeIntegrated voltage testLow voltage alarmLED indicator:Indicates the multi-copter status in real-timeStandard accessory: USB moduleFeatures:Support 9 kinds of multi-copter. With 3 servo ports for higher compatibilityAccurate speed control under GPS mode:Under GPS flight mode, the flight speed is proportionally equal to joystick movement, and the level speed is proportionally equal to throttle stick movement. Failsafe, one key go-home, IOC(Intelligent Orientation Control), POI(Point of Interest):If the multi-copter lost the signal, it can return to launch and land. When the signal works normally, pilot can pull and switch and activate one key go-home. Smart retractable landing gear:Once activate the feature, the landing gear will automatically extend in emergency case (ex: auto-landing). Pilot can control the landing gear through radio transmitter after flight height exceeds 5 meters. Flight range programmable and no-fly zone protect:Under GPS flight mode, the multi-copter will fly inside the setting range only. Under other flight mode, once the multi-copter fly outside the setting range, the auto return-to-launch will be activated. In places near airport and no-fly zone, the flying height and range are restricted. Prop failsafe (Hex-copter or above)For Hex or above copters, when one of the motor or prop doesn’t work, the multi-copter will fly normally.  

    $129.90 $120.81, Save 7% OFF

    SKU:ZYX25

    Weight: 0.50 kg

  • Acro Naze32 Flight Controller Board by AbuseMark (Rev.6)

    Naze32 is back with a brand new revision and its sure to keep you at the top of your game. STM32F103CBT6 32-bit ARM Cortex M3 processor (72MHz, 3.3V)Invensense MPU6500 MEMS accelerometer + gyroBMP280 BarometerBuilt-in Micro-USB for programming/firmware update36x36mm size, 5 gram weight w/o headersMade in JAPANShipping with 16V input capable voltage regulatorsThese come with pin headers (straight and right angle options), NOT soldered to the board. Naze32 rev6 Features:    USB on right side    PPM/PWM input as through-hole    3.3V, I2C on standard-size headers    Fully pinout compatible with rev5 accessories (OSDoge etc)    SBUS Inverter    Spectrum satellite    MPU6500    Sonar pads w/resistors added for direct connection to 5V sonar    All extra pads (FT, GP, A5) on top, only sonar on bottom    BMP280 barometer    16mbit flashSpecs:    36x36 mm (30.5mm Mounting)    5.3 grams (no headers, 7.3 grams with)    2000 degrees\second 3-axis MEMS gyro + accelerometer (MPU6500)    Input voltage: Max 16V on input rail and up to 35V 6s on the voltage sense lineIncluded: 1x  Acro Naze32 rev6 1x  pin header 1x  Breakout cable Attention (Update on 10/15/2015): Naze32 Rev 6 flight controllers are a new design and some changes have been made that are different from the Rev 5 flight controller. Please keep in mind that when the board is connected to a fully assembled multi rotor a direct connection to USB port on a computer can supply the entire multi rotor with 5 volts of power, please pay attention and make sure all parts are connected properly. Update on 09/21/2015: The Naze32 now has been upgraded from Reversion 5 to Reversion 6This product has different colors (white, red, black and blue), and we will ship it to you with the color at random. Before purchasing, please make sure you accept this. Thank you!

    $15.60

    SKU:NAZE32-A+C

    Weight: 0.10 kg

Find us on Google+ Watch us on Youtube Like us on Twitter Follow us on Facebook

Home   |   About Us   |   New Products   |   Multi-Rotors   |   FPV Airplanes   |   FPV Equipment   |   Battery / Chargers   |   Tools & Accessories   |   Contact Us   |   Blog   |  Site Map

Product Tags: ABCDEFGHIJKLMNOPQRSTUVWXYZ0-9

Copyright © 2015 FPVMODEL.COM®. All Rights Reserved.