Sorted:
  • DYS ARIA 35A 3-6S Blheli_32 Dshot1200 ESC

    It is always better late than never. Finally the DYS Aria 35A BLHeli_32 ESC is officially launched. If you are still running its XM30A, this could be a very good upgrade for the BLHeli_32 goodness.DYS ARIA 35A 3-6S Blheli32 Dshot1200 ESCSpecifications:Current Rating: 35A (40A burst)Voltage Rating: 3S to 6SDimension: 32mm x 16mm x 5mmWeight: 4.73g bare PCB, 8.1g with wiresCurrent sensing and limitingBuilt-in Programmable RGB LEDPrice: $15.99 eachSupports DShot1200 and older ESC protocolsFeatures:With 32bit ARM Cortex MCU STM32F051 48MHZ micro processor, throttle 2048 resolution ratio, strong anti-interference capacity.Built-in sensor can be reaction of temperature, output power, output current etc, also programmable for protection.Support Blheli_32 firmware, can use the signal wire to upgrade the firmware or change the configuration on line.Current Meter to help show current indication of OSDWith USB linker can be programmable throttle setting like support positive and negative, two way mode, FPV 3D mode, motor speed, braking, PWM frequency, inlet angle speed setting, onboard RGB LED for customize color, Beep etc.It use the self-adaption control system,can go automatic with the all kind of the motor in the market,at the mean time it support up to 500HZ PWM, oneshot 125, oneshot 42, Multishot and Dshot 150/300/600/1200.With special optimize in multi-axis, the motor can launch smoother in a good throttle curve, fast response,great power, and highly support the multi-axis,fixed-wing and helicopter.The twisted-pair signal wire can lower the crosstalk inside cooper wire when it transfer,which will make the flight more stable.MCU hardware,Driver circuit, Mosfet will come with double voltage protection.To adopt the new process MOSFET of low internal resistance, will help increase resistance to flow. Also, the professional MOS driver chip makes the best efficiency.Mosfet is covered with aluminum sheet for cooling,which can bring more efficiency and stability.With special process of 6 layer thicken PCB will lower resistance, small calorific value and bigger impact resistance current.Nice optimize layout of the components and parts makes a smaller size, lighter weight and easy to build.

    $15.99 $14.07, Save 12% OFF

    SKU:DA35A

    Weight: 0.10 kg

  • Betaflight 32Bit 35A 2-6S BLHeli_32 ESC Dshot1200

    *** This is the new updated version of Betaflight BLHeli_32 ESC that comes with a line of soldering along the ESC sides for a better protection and giving more power. We are at it again and the guys at Betaflight, FPV Model, BLHeli, and Airbot have come together to create a version of BLHeli_32 ESCs that FPV Model hopes will not disappoint. Introducing a fresh take on an ongoing development with BLHeli_32 we are introducing BetaBees, BlHeli_32 ESCs designed in conjunction with Airbot.BLHeli_32 is the third generation BLHeli code, following base BLHeli and BLHeli_S. It runs on an ARM 32bit MCU, initially it will be on a Cortex-M0 running at 48MHz, but there are MCUs out there that can run a lot faster.  BLheli_32 can run input signals with lower latency at faster rates. Dshot up to at least Dshot1200, and at rates up to at least 32kHz is now supported.Here is what BLHELI_32 has to say about their new "Power to perform":Programmable PWM frequency of up to 48KHzAuto-timing for higher efficiency and reliabilityVoltage/Current limitingAdjustable “Brake on Stop” forceImprove direction change in Bidirectional modeESC TelemetryConfiguring from FC using DShot commandsFeatures: Built in Current SensorExtra capacitors to help smooth noisy envrionments.Customizable color choice RGB LED using Blheli_32 software.Large positive and ground pads for easy soldering. 2-6s Lipo input35A continuous current  (can handle burst above 45A but please be reasonable, do not overwork  your motors)TX pad on ESC used for Telemetry pad. (connect to FC and you would get current sensing, motor RPM, ESC temperature etc)Specifications :Input: 2-6s LiPolyConstant: 35 AmpsBurst: 45 AmpsBEC: No BEC, OPTO onlyDimensions: 34x16x7mmWeight: 6g (without motor wires)Includes:1 x Betaflight BLHeli_32 35A ESC1 x 16AWG Red Silicon Wire 10cm1 x 16AWG Black Silicon Wire 10cm3 x 20AWG Black Silicon Wire 10cm1 x 26AWG Red Silicon Wire 10cmSome Tips:BLHeli_32 ESC Firmware OverviewHow to Connect BLHeli_32 ESC to Congigurator BLHelisuite32 via FC PassthroughWhat is Dshot1200 and Why Dshot1200 is Better?How to Get Dshot1200 Running in Betaflight?Downloads:Download the latest BLHeli_32 Configurator here.Download the BLHeli_32 User Manual here.Download Betaflight 3.2.0 here.We have made a slight change to the second version of Betaflight 32bit BLHeli ESC. The soldering of previous version already connected while the new version not, so as to make the wiring cleaner.

    $18.99 $17.47, Save 8% OFF 1

    SKU:BFESC3

    Weight: 0.10 kg

  • Favourite Littlebee Summer 2-6s BLHeli_32 30A Dshot1200 ESC

    Following the 35A, FVT just released its new 30A version of Littlebee Summer ESC. This new 30A comes with 2-6s input. The burst current can be up to 35A / 10s. It has current sensor, while the 35A version does not.Feature: 1:input Voltage:2-6S Lipo 2:NO BEC 3:Continue Current:30A,Burst Current:35A up to 10S 4:Size: 31*17mm. 5:Weight:8g(include Power and signal wire) 6:Support Oneshot125,Oneshot42,Mutishot and at least Dshot1200 etc. 7:Main IC:runs on an ARM 32bit MCU(STM32F051),running at 48MHz 8:MOS:Both low and high side fets are Nfets,szie is 5*6,easy to heat 9:programmable pwm frequency, up to 48kHz,run motors even smoother 10:Low voltage ,temperature and current protection 11:New telemetry function 12:BLHeli-32 Bootloader & Firmware

    $17.99 $9.89, Save 45% OFF

    SKU:FVT30A

    Weight: 0.10 kg

  • RaceFlight Bolt 4n1 ESC

    The RaceFlight Bolt 4n1 electronic speed controller (ESC) provides the power of BlHeli_S performance in a slim package. This makes your electronic stack slim, and generally eliminates the need for an additional PDB. The 4n1 ESC performs great and helps clean up any build.The RaceFlight 4n1 is also extremely easy to install. It is compatible with 4s through 6s batteries and has a built-in current sensor that hooks up directly to the Revolt to provide mAh information. The whole 4n1 ESC pins directly to the Revolt flight controllers and also sends voltage.Specifications30.5mm x 30.5mm mounting hole spacing30 amp continuous draw per motor40 amp burstBlHeli_S5V voltage regulator capable of 3A continuous outputD-Shot ready4s – 6s compatibleBuilt in Current SensorPins to Flight controllerCurrent and Voltage sent to flight controllerEasy InstallHigh-quality components

    $64.99 $61.09, Save 6% OFF

    SKU:RFB41E

    Weight: 0.10 kg

  • Wraith32 MINI- 32bit BLHELI_32 ESC

    Specifications:2-6s LIPO input25A designed10*20mmBLHeli_32 is the third generation BLHeli code, following base BLHeli and BLHeli_S.BLHeli_32 runs on an ARM 32bit MCU, initially it will be on a Cortex-M0 running at 48MHz, but there are MCUs out there that can run a lot faster.So what can the increased MCU speed do?First of all, it can run input signals with lower latency at faster rates. Dshot up to at least Dshot1200, and at rates up to at least 32kHz is now supported.Secondly it allows packing of more functionality. - Like programmable pwm frequency, up to 48kHz, that can run motors even smoother, and also allows for moving of small but potentially disturbing humps in the throttle response. All ESCs have these bumps, with BLHeli_32 they can now be moved in the rpm range, to a place where the system has low sensitivity to them.- Like auto timing. Which is not the option to choose if you’re after max power. But if you want the most efficient running with very good robustness against desync, it is the perfect choice.- Like voltage and current limiting. Which is implemented in the code, and will be supported on some ESCs. Voltage limiting is desirable for fixed wing crafts. And current limiting adds protection against ESC failure.- Like programmable brake on stop force. Which allows control of the braking of fixed wing props.- Like improved direction change in bidirectional mode.- Like more to come in the future. Such as setup from the FC by using Dshot commands. Such as telemetry functionality. There is room to grow performance and functionality.Some Tips:BLHeli_32 ESC Firmware OverviewWhat is Dshot1200 and Why Dshot1200 is Better?How to Get Dshot1200 Running in Betaflight?Downloads:Download the latest BLHeli_32 Configurator here.Download the BLHeli_32 User Manual here.Download Betaflight 3.2.0 here

    $14.99 $12.29, Save 18% OFF 1

    SKU:WMN32

    Weight: 0.10 kg

  • X-Racer Quadrant 2-6S 35A 32Bit BLHeli_32 ESC Dshot1200

    Features of New X-Racer Quadrant 35A 2-6S 32Bit BLHeli_32 ESC:Uses the latest BLHeli_32 firmware. Dshot up to at least Dshot1200.At rates up to at least 32kHz is supported.Four tiny ESCs can be installed separately on the arms, or installed together like a PCB under the flight controller.2-6s Lipo input.Rated at 35A current with a max of 50 amps of current load (Less than 10s).Small in size: 20 x 24mm3 grams each piece and about 12 grams for a set of 4 pieces.Compatible to BetaflightF3 Flight ControllerThe new X-Racer Quadrant BLHeli_32 ESC has followed the design of previous 4-in-1 design of X-Racer Quadrant. It is not a single board, but four tiny ESCs can be installed separately on the arms, or installed together like a PCB under the flight controller. This is the 35A version, there is also another 25A version available for your choice.The new X-Racer Quadrant 35A is flashed with the latest BLHeli_32 program. Dshot up to at least Dshot1200, and at rates up to at least 32kHz is now supported. BLHeli_32 is the 3rd generation of BLHeli firmware after BLHeli and BLHeli_S. BLHeli_32 runs on an ARM 32bit MCU, initially it will be on a Cortex-M0 running at 48MHz, but there are MCUs out there that can run a lot faster. The way “pass-through” works is quite similar to previous versions such as BLHeli_S. Basically it uses the flight controller as a programming tool or adapter to allow the computer to talk to the ESC’s directly, so you can change settings or flash new firmware etc.So what can the increased MCU speed do?First of all, it can run input signals with lower latency at faster rates. Dshot up to at least Dshot1200, and at rates up to at least 32kHz is now supported.Secondly it allows packing of more functionality. - Like programmable pwm frequency, up to 48kHz, that can run motors even smoother, and also allows for moving of small but potentially disturbing humps in the throttle response. All ESCs have these bumps, with BLHeli_32 they can now be moved in the rpm range, to a place where the system has low sensitivity to them.- Like auto timing. Which is not the option to choose if you’re after max power. But if you want the most efficient running with very good robustness against desync, it is the perfect choice.- Like voltage and current limiting. Which is implemented in the code, and will be supported on some ESCs. Voltage limiting is desirable for fixed wing crafts. And current limiting adds protection against ESC failure.- Like programmable brake on stop force. Which allows control of the braking of fixed wing props.- Like improved direction change in bidirectional mode.- Like more to come in the future. Such as setup from the FC by using Dshot commands. Such as telemetry functionality. There is room to grow performance and functionality.Software SetupYou will need to flash Betaflight V3.2 or newer firmware on your FC, you can download it from: https://github.com/betaflight/betaflight/releases/tag/v3.2.0.Load the firmware target for your FC locally, and flash (shouldn’t need to short bootloader pins)Download latest BLHeliSuite for BLHeli_32: http://www.blheli32.com/download/Some Tips:BLHeli_32 ESC Firmware OverviewWhat is Dshot1200 and Why Dshot1200 is Better?How to Get Dshot1200 Running in Betaflight?DownloadsDownload the latest BLHeli_32 Configurator here.Download the BLHeli_32 User Manual here.Download Betaflight 3.2.0 herePack for one piece.Pack for a set of 4 pieces.

    $18.99 $13.10, Save 31% OFF

    SKU:XQ35B32

    Weight: 0.10 kg

  • X-Racer Quadrant 2-6S 25A 32Bit BLHeli_32 ESC Dshot1200

    Features of New X-Racer Quadrant 25A 2-6S 32Bit BLHeli_32 ESC:Uses the latest BLHeli_32 firmware. Dshot up to at least Dshot1200.At rates up to at least 32kHz is supported.Four tiny ESCs can be installed separately on the arms, or installed together like a PCB under the flight controller.2-6s Lipo input.With 25AMp constant RMS, 30A max.Less than 3 grams each piece and about 11.5 grams for a set of 4 pieces.Small in size: 18 x 24mmCompatible to BetaflightF3 Flight ControllerThe new X-Racer Quadrant BLHeli_32 ESC has followed the design of previous 4-in-1 design of X-Racer Quadrant. It is not a single board, but four tiny ESCs can be installed separetely on the arms, or installed together like a PCB under the flight controller. This is the 25A version, there is also another 35A version available for your choice.The new X-Racer Quadrant 25A is flashed with the latest BLHeli_32 program. Dshot up to at least Dshot1200, and at rates up to at least 32kHz is now supported.BLHeli_32 is the 3rd generation of BLHeli firmware after BLHeli and BLHeli_S. BLHeli_32 runs on an ARM 32bit MCU, initially it will be on a Cortex-M0 running at 48MHz, but there are MCUs out there that can run a lot faster.So what can the increased MCU speed do?First of all, it can run input signals with lower latency at faster rates. Dshot up to at least Dshot1200, and at rates up to at least 32kHz is now supported.Secondly it allows packing of more functionality. - Like programmable pwm frequency, up to 48kHz, that can run motors even smoother, and also allows for moving of small but potentially disturbing humps in the throttle response. All ESCs have these bumps, with BLHeli_32 they can now be moved in the rpm range, to a place where the system has low sensitivity to them.- Like auto timing. Which is not the option to choose if you’re after max power. But if you want the most efficient running with very good robustness against desync, it is the perfect choice.- Like voltage and current limiting. Which is implemented in the code, and will be supported on some ESCs. Voltage limiting is desirable for fixed wing crafts. And current limiting adds protection against ESC failure.- Like programmable brake on stop force. Which allows control of the braking of fixed wing props.- Like improved direction change in bidirectional mode.- Like more to come in the future. Such as setup from the FC by using Dshot commands. Such as telemetry functionality. There is room to grow performance and functionality.Some Tips:BLHeli_32 ESC Firmware OverviewWhat is Dshot1200 and Why Dshot1200 is Better?How to Get Dshot1200 Running in Betaflight?Downloads:Download the latest BLHeli_32 Configurator here.Download the BLHeli_32 User Manual here.Download Betaflight 3.2.0 here.

    $18.15 $9.98, Save 45% OFF 1

    SKU:XQ25B32

    Weight: 0.10 kg

  • Wraith32 - 32bit 35A BLHeli_32 ESC DSHOT1200

    *** These are the final upgradable version of Wraith32 BLHeli_32 ESCs. Please rest assured to buy and use. *** Friendly Reminder: If you are using high KV motors, please add a line of soldering along the ESC sides for a better protection and to give more power.Wraith32 is the first 32bit BLHELI ESC that use the latest BLheli_32 firmware in the world. Dshot up to at least Dshot1200, and at rates up to at least 32kHz is now supported. If you are seeking for a small, powerful blheli_32 capable 32bit ESCs, the Wraith32 ESCs will certainly fit the bill providing 35Amps of power.The Wraith32 ESC runs in conjunction with an ARM 32bit compatible MCU. It can run input signals with lower latency, at faster rates, smooths out the RPM band, is capable of both voltage and current monitoring and limiting, as well as offering customization of the brake on stop force. Unlike current ESCs, the Wraith32 ESC has A LOT of room to grow and wide compatibility range with future products. One of the nicest features with the Wraith32 35A ESC is the auto timing feature, which (essentially) is designed to offer the pilot the smoothest and most efficient flight experience available, which is a freestyle pilots dream come true! Features:32bit Compatible ESC (Blheli_32)Dshot1200 up to 32kHzIncredibly small sizeVery low weightAuto Timing FeatureOn-Board RGB LEDBuild in Current sensorSmooth ResponseCompatible to BetaflightF3 Flight ControllerSpecifications:2-6s Lipo input35A designedCompatible to BetaflightF3 Flight ControllerSize: 15*30mmPackaging: One ESC each PP bag with Wraith32 lable.BLHeli_32 is the 3rd generation of BLHeli firmware after BLHeli and BLHeli_S. BLHeli_32 runs on an ARM 32bit MCU, initially it will be on a Cortex-M0 running at 48MHz, but there are MCUs out there that can run a lot faster.Now the first ESC that supports BLHeli_32 has already been announced – the Wraith32 and Wraith32 Plus. Luckily, FPV Model received these from the manufacturer Airbot as soon as they made them out, and all our customers have the chance to be the first in the world receive these new BLHeli_32 ESCs.Wraith32 Plus is a 6S powerhouse that supports voltage limiting and current limiting as well as a bright RGB LED.Wraith32 is a smaller 6S version that also supports voltage limiting and current limiting as well as a bright RGB LED.So what can the increased MCU speed do?First of all, it can run input signals with lower latency at faster rates. Dshot up to at least Dshot1200, and at rates up to at least 32kHz is now supported.Secondly it allows packing of more functionality. - Like programmable pwm frequency, up to 48kHz, that can run motors even smoother, and also allows for moving of small but potentially disturbing humps in the throttle response. All ESCs have these bumps, with BLHeli_32 they can now be moved in the rpm range, to a place where the system has low sensitivity to them.- Like auto timing. Which is not the option to choose if you’re after max power. But if you want the most efficient running with very good robustness against desync, it is the perfect choice.- Like voltage and current limiting. Which is implemented in the code, and will be supported on some ESCs. Voltage limiting is desirable for fixed wing crafts. And current limiting adds protection against ESC failure.- Like programmable brake on stop force. Which allows control of the braking of fixed wing props.- Like improved direction change in bidirectional mode.- Like more to come in the future. Such as setup from the FC by using Dshot commands. Such as telemetry functionality. There is room to grow performance and functionality.Some Tips:BLHeli_32 ESC Firmware OverviewWhat is Dshot1200 and Why Dshot1200 is Better?How to Get Dshot1200 Running in Betaflight?Downloads:Download the latest BLHeli_32 Configurator here.Download the BLHeli_32 User Manual here.Download Betaflight 3.2.0.Before Purchasing: The products come with different batches may have different silk printing on them.

    $16.99 $14.95, Save 12% OFF

    SKU:W32E

    Weight: 0.10 kg

  • KISS ESC 2-5S 24A Race Edition V1.03, A Set of 4pcs

    *** ?FPV Model is an authorized?dealer of FLYDUINO KISS. Genuine KISS ESC guaranteed.KISS ESC 24A Racing Edition V1.03, Price for one set of 4pcs. This ESC is also available at US Warehouse. If you are from the United States, please buy at US Website directly for a faster shipping.In the sense of our KISS ESC line this ESC offer a great compability to a wide range of motors, the work of years went in to making the best possible here.The fast 32it Arm Cortex CPU does a very good job and runs the ESC very effective, of course reaction times are top notch.The 24 RE is layed out as a beefy ESC which withstand quite some abuse due to FPV races, several mechanisms doing its best to protect your valuable equipment, the rating of 24A wont need direct cooling, mounting them partially covered is ok.No need to worry with different firmwares, simply solder and fly (some solder skills are the only needed skills).First ESC with with oneshot42 support (dont worry, Oneshot125 and normal PWM are auto detected too).Beside this, this is the first ESC who offer a easy to use telemetry function over the regular servo connector which you can use in combination with our KISS-FC, no external heavy parts needed anymore to have infos like voltage, ampere and even your RPM on your OSD (MinimOSD supported) or on your receiver LCD screen (Frsky-Taranis, f.e.).Features:- 32-bit ARM Cortex MCU@48Mhz- Telemetry capable (voltage, current, temperature, RPM)- Overcurrent protection (measures the current and reduces it to a max of 30A)- Over temperature protection (reduces max power if temp exceeds 120°C)- Expanded adaptive auto timing- Specifically designed for racing drones (24 amps continuous even with bad cooling)- High max RPM (64000 with a 14 pole motor)- Accurate RPM control (950 step resolution)- Very fast throttle response- Linear throttle response- Active freewheeling- Regenerative braking- No external electrolytic capacitor required- Fast FET switching due to the use of gate drivers- Small and lightweight (19 x 27mm) (3.6g)Specifications:- Current Draw: 24A Continuous- Voltage Range: 2-5s Lipo- Weight: 3.53g- Size: 19mm x 27mm x 4.5mm

    $98.99 $87.11, Save 12% OFF

    SKU:4KSE24

    Weight: 0.10 kg

  • BumpBee BLheli_S 30A 3S-6S ESC w/ Oneshot / Multishot Support

    mini Race HK From Bumpbee by Ka KeiBumpBee BLHeli_S ESC runs BLHELI_S (J_H_90) firmware on BB21 MCU.  It offers the best performance for racing multirotors. It uses the QFN5x6 Power Mosfet instead tiny QFN 3x3 Mosfet that most of other ESCs use, delivering more current, with better cooling and less heating. The input voltage is up to 24.8V. Features:- BB21 MCU, Runs BLHELI_S firmware (J_H_90)- Oneshot / Multishot support - Support 3S-6S - 3X RGB LED- 15*30mm - Weight: 2.9g

    $12.90 $8.26, Save 36% OFF

    SKU:BBEP-B

    Weight: 0.10 kg

  • BumpBee Pro 30-35A 3S-6S ESC with BLHELI Firmware

    BumpBee ESC gives new option for miniESC, upgraded to much better MOSFET, runs cooler and more AMPs compare to standard miniesc. The BumpBee ESC uses F396 MCU, supports full featrues from BLHELI and can be soldered on PDB directly.Feature:- F396 MCU, Runs BLHELI Littlebee Pro firmware- 30-35A- 3-6S- Only 15x30mm

    $10.99 $5.93, Save 46% OFF

    SKU:BBEP

    Weight: 0.10 kg

  • LittleBee 20A-S BLHeli_S ESC

    These new LittleBee blheli_s 20amp escs are some of the new generation of littlebee escs that feature the blheli_s firmware. The hardware and software advancements in Blheli_s are responsible for an ultra smooth throttle response, which ultimately translates into the smoothest handling flying experience to date.The Littlebee 20A-S escs have there own didicated Driver Chip with the blheli_S compatable bootloader, and also come with BL-Heli_S pre installed! Features:Input Voltage: 2 - 4S Lipo (7.4v - 14.8v)BEC: Opto ESC (NO BEC)Current draw: Continuous Current up to 20Amps, Burst Current up to 25 Amps for 10 secondsSize: 23.5mm x 12mmWeight: 4g (including Power and signal wires)Support/Mode: Oneshot125, Oneshot42 and MultishotMain IC: SILABS EFM8BB21F16, MCU runs at 48MHzMOS: Both low and high side fets are Nfets

    $14.59 $7.88, Save 46% OFF

    SKU:LB20A-S

    Weight: 0.10 kg




Find us on Google+ Watch us on Youtube Like us on Twitter Follow us on Facebook

Home   |   About Us   |   New Products   |   Multi-Rotors   |   FPV Airplanes   |   FPV Equipment   |   Battery / Chargers   |   Tools & Accessories   |   Contact Us   |   Blog   |  Site Map

Product Tags: ABCDEFGHIJKLMNOPQRSTUVWXYZ0-9

Copyright © 2015 FPVMODEL.COM®. All Rights Reserved.