Sorted:
  • BetaflightF7 RV1 Flight Controller

    Betaflight F7 is here and it features a completely new layout. Top mounted solder pads ensure ease of access for the even the trickiest of builds. The Betaflight F7 features dual gyros so the user can have their choice of which one to use, either the tried and true MPU6000, or the ICM20608. You’ll find the specs listed below:Specifications:3-6s Simplistic LayoutTwo Gyro optionsBetaflight OSDFiltered output for FPV systemsSmart Audio/Tramp Telemetry compatibily4 uarts (can read inverted and univerted signals)Camera Control BuzzerBlackbox via flash memory 30.5x30.5 FC mountingBetaflightF7 Setup Guide: Features: Programmable LEDs, Flash Memory, individual pad for camera control, labeled Smart Audio/Tramp TX1 next to VTx soldering pads. Labeled Smart Port TX2 pad next to Sbus/Ibus/DSM2 UART6 Tx, 5v and 3.3v pads (user selection based on type of receiver used), four pads for ESC telemetry connected to RX1.(Each pad placed near corners of the board) By Philipp Seidel, Click to Enlarge

    $59.99

    SKU:BFF7

    Weight: 0.10 kg

  • Dragonfly Hurricane 2207 KV2500 Brushless Motor for FPV Racer

    Specially deisigned for FPV racing with extreme performanceFast response and ultimate efficiencyNew technology to ensure smooth runningPrecise balanced and fully testedPowerful, reliable, and quick. This is the latest Dragonfly Hurricane 2207 2500KV brushless motor that specially designed for FPV racing and extreme performance. These Dragonfly Hurricane 2207 2500kv motors feature an open air base to allow for more efficient cooling of the motors. Weighing in at just 30.5 grams helps eliminate some weight compared to other motors and fits with most racers desire to shave precious grams off builds wherever they can.Features:Featuring 20awg silicone wire, N52SH magnets and Japanese NSK bearings these motors are sure to fit the needs of most FPV racers.We use high quality aluminum and rare-earth magnetic materials, and redesigned the magnetic circuit of Dragonfly Hurricane to make sure the motors come with a better loading capacity.We have greatly improved their thrust and efficiency comparing to other motors on the market. At the same time, we have enhanced the response speed to guarantee the smooth flying of your racing quadThe use of special aluminum material for body structure, not only comes with a greater strength than those motors made of the 6 series aluminum that most other motors use, but also greatly reduce the weight. The motor shaft has abandoned the traditional way of installation, the spindle completely goes through the threaded shaft to improve the friction between steel shaft and threaded sleeve of head cover. It also improves the concentricity of motor rotor and effectively increases the strength of propeller shaft, so that to make sure the motor can survive from the hard crashes.The Draongfly Hurricane has added an insulation film between bottom cover and spindle to isolate the connection between screws and copper wires. In this way, the motor is able to prevent from short circuit and leakage that caused by misoperation.Specifications:KV: 2500KVNo.of Cells(Lipo): 3-5SConfiguration: 12N14PStator Diameter: 22mmStator Length: 7mmShaft Diameter: 5mmMotor Dimension (Dia.*Len): Φ27.9×32.7mmWeight(g): 30.3g(Excluding Cable)Recommend Propeller: 5″Recommend ESC: 30-50AWire AWG: 20AWG|Magnet: N52SH Stator: Japan KAWASAKIBearings: NSKThese Dragonfly Hurricane 2207 2500kv motors feature an open air base to allow for more efficient cooling of the motors. Weighing in at just 30.5 grams helps eliminate some weight compared to other motors and fits with most racers desire to shave precious grams off builds wherever they can.We use high quality aluminum and rare-earth magnetic materials, and redesigned the magnetic circuit of Dragonfly Hurricane to make sure the motors come with a better loading capacity.Featuring 20awg silicone wire, N52SH magnets and Japanese NSK bearings these motors are sure to fit the needs of most FPV racers.The Draongfly Hurricane has added an insulation film between bottom cover and spindle to isolate the connection between screws and copper wires. In this way, the motor is able to prevent from short circuit and leakage that caused by misoperation.

    $13.99-$54.99

    SKU:DG0725

    Weight: 0.10 kg

  • Robotdog 35A 32Bit 2-4S BLHeli_32 ESC Dshot1200

    * MSRP $15.00, for a limited time, the Robotdog is sold at $9.9 only. Dont miss it out if you are buiding on budget.The low price does not mean that the Robotdog is lacking power. It has all features a 32bit BLHeli ESC has!!! 35A designed, ARM 32bit Cortex-M0 MCU, 1500uF cap onboard, 2-4s input and Dshot at least Dshot1200.Robotdog 35A is a new 32bit BLHELI ESC from Battle RC that uses the latest BLheli_32 firmware. Dshot up to at least Dshot1200, and at rates up to at least 32kHz is now supported. If you are seeking for a small, powerful blheli_32 capable 32bit ESCs, the Robotdog ESCs certainly fit the bill providing 35Amps of power.BLHeli_32 is the third generation BLHeli code, following base BLHeli and BLHeli_S. It runs on an ARM 32bit MCU, initially it will be on a Cortex-M0 running at 48MHz, but there are MCUs out there that can run a lot faster. ?BLheli_32 can run input signals with lower latency at faster rates. Dshot up to at least Dshot1200, and at rates up to at least 32kHz is now supported.Here is what BLHELI_32 has to say about their new "Power to perform":Programmable PWM frequency of up to 48KHzAuto-timing for higher efficiency and reliabilityVoltage/Current limitingAdjustable “Brake on Stop” forceImprove direction change in Bidirectional modeConfiguring from FC using DShot commandsFeatures:Blheli_32 codeARM 32bit Cortex-M0 MCUDshot up to at least Dshot12001500uF cap onboard2-5s LiPo input (as per our test, no problem to use with 5S.) .35A designed15*25mmSome Tips:BLHeli_32 ESC Firmware OverviewHow to Connect BLHeli_32 ESC to Congigurator BLHelisuite32 via FC PassthroughWhat is Dshot1200 and Why Dshot1200 is Better?How to Get Dshot1200 Running in Betaflight?Downloads:Download the latest BLHeli_32 Configurator here.Download the BLHeli_32 User Manual here.Download Betaflight 3.2.0 here.

    $15.00 $9.90, Save 34% OFF

    SKU:RD35A

    Weight: 0.10 kg

  • BetaflightF4 Flight Controller

    BetaflightF4 How to ESC Telemetry, Smart Port Audio, Smart Port TelemetryFriendly Reminder: Upon receiving your FC, please connect to USB and calibrate before continuing to build and solder to it.  BetaflightF4 is the follow up design to the very popular BetaflightF3. Following in the same path as Betaflight F3 we have kept a very similar footprint in terms of design with a few added modifications. The F405 has replaced the F303 to allow for lower CPU loads.We have eliminated the 5v/3.3v jumper and added two seperate connection points, one for sbus and one for spektrum users. The jumper still remains for the battery voltage/5v connection for connecting your camera. While wiring the board it is recommended to get power for your vtx either from a different 5v source on the board or if using a higher voltage vtx power it from the battery input coming into the pdb. Running ground loop at Agnd with gnd wires from camera and vtx is still recommended to give the cleanest video signal. Another small design change to this board was changing the BEC, this change takes the recommended 5v 2A current limit and drops it down to 5V 1.5A, its a small change but one that we opted for in order to use a more reliable BEC.BetaflightF4 now comes with telemtry pads for BLHeli32 ESCs these pads are located between the signal and gnd pads for the ESC connections.FeaturesIntegrated PDBBuilt in OSD customizable via Betaflight OSDCurrent sensorIntuitive layoutFlash memory for blackboxTailored to support BetaflightWhen running 8K/8K, CPU usage remains lowSpecificationsF405 ProcessorMPU6000 Gyro/ACC SensorBEC Max current 5V 1.5ABuilt in OSD – configurable via Betaflight GUICurrent sensorPower distribution board with six-layer PCBOSD Max Current: 145AWiring Diagram - Click to enlarge!BetaflightF4 Connection Plan by Phillip SeidelBetaflightF4 Turtle Mode SettingBetaflightF4 OSD FlashingHow to Use ESC TelemetryBetaflightF4 Can not ArmHow to Use Smart Port TelemetryHow to Use BetaflightF4 IBUSThe Number of “Scale the Output Voltage to Miliamp” in BetaflightHow to Set Tramp HV VTXIf you are meeting a problem with the use of flight controller and can not find the answer, please submit your question.

    $44.73 $33.99, Save 24% OFF 3

    SKU:BFF4

    Weight: 0.10 kg

  • Betaflight Hive Backpack

    Betaflight FPV Backpack | BEST FPV BACKPACK? By Joshua Bardwell* Before Purchasing: Due to the size limit, we offer free shipping on the backpack by EMS only. For some areas where EMS can not reach, we might change to ship via another shipping company.This is the Betaflight Hive Backpack. The design of this bag has taken many months and even after we released it for pre-orders, customer suggestions kept making us go back to the "final" prototype and add some of their suggestions. In reality, this is not just a backpack that was designed by us but its more of a backpack that has been designed and then re-designed by users like you. We do our best to listen to your feedback and that is proven in the design of this backpack. Requests for hard shell covers, reverse the orientation of the side pockets, make the hand held carry bgk into a liposafe fire-resistant bag are just a few of the suggestion that we went back and updated during the design process. After reviewing the final, final prototype we here at FPV Model feel like the user sugguestions weve received from our clients and friends on facebook, have helped make certain that this bag has the best quality and features available. We think youre gonna like them. The overall design of this backpack is geared towards those that are serious fliers and have multiple quads and many tools and accessories that they carry with them while traveling by air or even just to the local field. Betaflight Hive Backpacks are performance tested, at fully loaded capacity, using our strict control standards. Before we offer this product for sale, it is put through test to ensure it’s strength, durability, and dependability that is represented by the most demanding frequent travelling quad pilots. This attention to quality results in us (FPV Model) and (Betaflight) being able to offer the best warranty in the industry. Click here for the backpack warranty or download the PDF.Features:International carry-on size compatibility for air travel. Dedicated lap-top pocketDedicated fireproof lipo bagElastic daisy chain tool panel for your hex drivers and other hand held tools. Large interior pocket for carrying props with hard shell cover on the bag for added protection from outside forces. 1680D ballistic nylon bag material for long life durability. Featuring the best zippers in the market made by YKK to ensure long lasting zipper life. Contoured adjustable padded harness with height adjustable chest strap. Rain cover that pulls out from bottom panel pocket for fast rain protection.Exterior Dimensions:  56 x 34 x 18cmLarge interior pocket for carrying props with hard shell cover on the bag for added protection from outside forces.Interior and Exterior FPV Quad mounting locations.While we were designing the Betaflight backpack one thing kept coming up in the design aspect was how much room the transmitter took up inside the bag. So, we thought the best design would be to make a hard shell top mounted case on the top of the bag. The hard shell top of the case allows for extra protection of your transmitter and frees up valuable space inside the bag. The interior of the bag is very similar to other DSLR style camera bags and allows for multiple design layouts by using cushioned dividers that velcro in place and let each user layout their own custom setup based on their specific needs. Featuring the best zippers in the market made by YKK to ensure long lasting zipper life. Dedicated fireproof lipo bag to store your Lipos, no need to worry about the safety of batteries now. Still Plenty room to store your FPV accessories, you are able to carry up to 30 1500mAh batteries!!!Dedicated laptop pocketWe pay attention to every detail of the backpack. The inside fabrics come with Betaflight Logo. Plenty room to put your little stuff inside.The Betaflight Hive Backpack comes with a waterproof cover that placed in the bottom pocket. You can take it out from the backpack for added protection in case it is raining.Decent custom packaging box.Comes with a GoPro mount, recording every wonderful moment has never been so easy.  (GoPro camera not included)**** Friendly reminder: Price for Betaflight HIVE backpack only. Above pictures for demonstration purpose that the quads, tools, GoPro and other accessories are not included.

    $199.99    4

    SKU:BFBP

    Weight: 4.00 kg

  • X-Racer X-1 F3 Fight Controller V2 with Frsky Rx and OSD Integrated

    The X-Racer X-1 Whoop flight controller is making a return with an all new update. We are always listening to what our customers say and we have made some improvements accordingly. In reality, this is not just a simple whoop flight controller that was designed by us but its more of an FC that has been re-designed by users like you.This micro whoop brushed F3 flight controller was designed for X-Racer X-1, but it also can be used on those micro quadcopters like Tiny Whoop and Blade Inductrix.Features:1. The RX connection protocol has been upgraded from PPM to SBUS. With the SBUS protocol, you are able to get a faster response when the micro racer turn around.2. The integrated OSD (on screen display) is able to show some important flight data on your FPV feed, including battery voltage, current draw etc. You can even use it as a menu to change your quad’s PID, rates, filters and others.3. Larger MOS ensures a smoother flying with your micro racer. 4. The DC regulator module has been upgraded for a better loading capacity.5. Compatible with FrSky & SBUS, USB port ready.6. Pre-flashed with the latest Betaflight firmware.7. The binding buttons for the built-in Frsky RX have been updated, more convenient to use.How to Bind Built-in FrSky RX.1. Press "Band" to power on the quad, the middle red LED will turn on.2. Turn on your FrSky transmitter, set the mode to D8, 1-16CH, and then start to bind.3. After successfuly binding, on the right corner the red LED will start to slowly flash.4. Re-power on the flight controller, the binding is completed.How to Bind other RX.1. Connect the FC to Betaflight.2. Enter following instruction in CLI: set sbus_invention = on. And then save.3. The UART needs to choose 3.(Please take a note that the FC automatically works with the built-in FrSky RX, if you want to use with other RX, please set the CLI before using.)

    $29.99

    SKU:XR1FCU2

    Weight: 0.10 kg

  • RunCam RC25G FPV Lens 2.5mm FOV140 Wide Angle for Swift Series Eagle 4:3 Series Split

    RunCam RC25G FPV Lens 2.5mm FOV140 Wide Angle for Swift Series Eagle 4:3 Series SplitPackage :1 X Lens1 X Lock Ring

    $12.99

    SKU:RC25G

    Weight: 0.10 kg

  • ZMR Eclipse 210mm ARF for Advanced Users

    ZMR Eclipse is a new 210mm carbon fiber mini quadcopter that designed based on the hot selling ZMR-X210. We are always listenting to what our customers say and made some slight changes to make it a better racing frame. For your easy setup, also considering on different users might have different requirements on the setups, we have prepared three different ARF packages of ZMR Eclipse for different levels of users, including:ZMR Eclipse ARF for FPV BeginnersZMR Eclipse ARF for Intermediate UsersZMR EClipse ARF for Advanced UsersThese are the ARF packages of ZMR Eclipse that specially prepared for serious advanced users. You are choosing these because you are very strict with the performance of your racing quads. To meet your expectations, we use Betaflight F4 AIO flight controller, one of the most reputable FCs in FPV community, on the builds. Better performance and easy to setup. Easy wiring, no need to use an extra PDB.In order to have a better compatible with Betaflight F4, we have changed to use Betaflight 35A 32bit BLHeli ESC. These ESCs have a soldering along the edges to allow more power going through. No need to worry about how much power you will give to them during flying.As to FPV camera, we use a better professional FPV camera, the RunCam Eagle 2. It is probably one of the best FPV cameras out there in terms of image quality and WDR capability. It has a clearer and better image, allowing the pilot to clearly obeserve the tiny objects even flying through a complex area, very suitable to use it for FPV racing.For the propellers, we have changed to use DalProp 5040. Many top pilots use these propellers for FPV racing! In general, comparing to the ARF packages for beginners and intermediates, the ARF packages for advanced users use the best flight controllers, ESCs, FPV camera and propellers to ensure the best performance. Furthermore, the weight have been saved a lot, the installation has been simplified.ARF 1 Including:ZMR Eclipse 210mm Carbon Fiber Mini FPV Quadcopter Frame Kit  * 1 setDragonfly Hurricane 2207 KV2500 Brushless Motor * 4 pcsBetaflight 32Bit 35A 2-6S BLHeli_32 ESC Dshot1200 * 4 pcsBetaflightF4 Flight Controller * 1 pcDALPROP Q5040 4-Leaf Props * 8 pairsAccessories Bag * 1 setARF 2 Including:ZMR Eclipse 210mm Carbon Fiber Mini FPV Quadcopter Frame Kit * 1 set RunCam Eagle 2 FPV Camera * 1 pcDragonfly Hurricane 2207 KV2500 Brushless Motor * 4 pcsBetaflight 32Bit 35A 2-6S BLHeli_32 ESC Dshot1200 * 4 pcsBetaflightF4 Flight Controller * 1 pcDragonfly 5.8G 48CH Stackable Video Transmitter * 1 pcDragonfly Transmitting Extension Cables * 1 pcDragonfly Booster 5.8G FPV Antenna 5cm SMA * 1 pcDALPROP Q5040 4-Leaf Props * 8 pairsAccessories Bag * 1 setARF1 Including:ARF2 Including:

    $179.99-$249.99

    SKU:ZMARF4

    Weight: 0.50 kg

  • ZMR Eclipse 210mm ARF for Intermediate Users

    ZMR Eclipse is a new 210mm carbon fiber mini quadcopter that designed based on the hot selling ZMR-X210. We are always listenting to what our customers say and made some slight changes to make it a better racing frame. For your easy setup, also considering on different users might have different requirements on the setups, we have prepared three different ARF packages of ZMR Eclipse for different levels of users, including:ZMR Eclipse ARF for FPV BeginnersZMR Eclipse ARF for Intermediate UsersZMR EClipse ARF for Advanced UsersCongratulations. You are now no longer an FPV newbie!!! Since that the ARF packages for beginners can not meet your requirements any more, you need a better setup. And these intermediate ARF packages are just made for you!We have made these ARF packages with a more powerful setting and comes with a better FPV image. The frist step, we have changed the motors to Dragonfly Hurricane 2207 2500kv motors. More powerful and faster respond speed. To match the motors, we have changed the ESCs to Robotdog as well. Robotdog is a 35A 32bit BLHeli_32 ESC, it supports Dshot1200 to ensure you a smooth flying.Considering the speed is now greatly improved, you have a higher requirement for the camera images. So we have changed the FPV camera to Runcam Swift 2. It is a professional FPV camera even no need to worry about backlight during flying.With the these setup, now you can try to join your local FPV community and race with other pilots. Maybe you are the next FPV champion.ARF 1 Including:ZMR Eclipse 210mm Carbon Fiber Mini FPV Quadcopter Frame Kit  * 1 setDragonfly Hurricane 2207 KV2500 Brushless Motor * 4 pcsRobotdog 35A 32Bit 2-4S BLHeli_32 ESC Dshot1200 * 4 pcsMATEK PDB XT60 with BEC * 1 pcOmnibus F4 V5 Flight Controller * 1 pcDYS 5040 4-Leaf Propeller CW+CCW 1 Pair * 4 pairsAccessories Bag * 1 setARF 2 Including:ZMR Eclipse 210mm Carbon Fiber Mini FPV Quadcopter Frame Kit * 1 set RunCam Swift 2 1/3 CCD IR Blocked Micro Camera * 1 pcRunCam RC25G FPV Lens 2.5mm * 1 pcDragonfly Hurricane 2207 KV2500 Brushless Motor * 4 pcsRobotdog 35A 32Bit 2-4S BLHeli_32 ESC Dshot1200 * 4 pcsMATEK PDB XT60 with BEC * 1pcOmnibus F4 V5 Flight Controller * 1 pcDragonfly 5.8G 48CH Stackable Video Transmitter * 1 pcDragonfly Transmitting Extension Cables * 1 pcDragonfly Booster 5.8G FPV Antenna 5cm SMA * 1 pcDYS 5040 4-Leaf Propeller CW+CCW 1 Pair * 4 pairsAccessories Bag * 1 setARF1 Including: ARF2 Including: 

    $149.99-$199.99

    SKU:ZMARF2

    Weight: 0.50 kg

  • ZMR Eclipse 210mm ARF for FPV Beginners

    ZMR Eclipse is a new 210mm carbon fiber mini quadcopter that designed based on the hot selling ZMR-X210. We are always listenting to what our customers say and made some slight changes to make it a better racing frame. For your easy setup, also considering on different users might have different requirements on the setups, we have prepared three different ARF packages of ZMR Eclipse for different levels of users, including:ZMR Eclipse ARF for FPV BeginnersZMR Eclipse ARF for Intermediate UsersZMR EClipse ARF for Advanced UsersThese are the ARF packages of ZMR Eclipse for FPV beginners. We built these aiming to provide you a durable setup with an extremely low cost. It can satisfy your daily practice like freestyle flying. If you are new to FPV, these are definitely perfect choices for you. These ARF packges for FPV beginners come with the reputable Omnibus F4 flight controllers, RJX 2205 2300kv brushless motors and Cyclone BLHeli_S 20A ESCs. We have tested all the parts to make sure they are matching well to have a good performance. The included Omnibus F4 flight controller is not just for beginners, but it is also greatly used in some advanced settings for professional pilots. The omnibus series of flight controllers are known to be the best all in one integrated flight controller, using the best selection of sensors and parts at a great price and small form factor. It uses the MPU6000/ICM-20608 IMU over SPI for the super fast gyro updates (up to 32Khz) to keep up with the fast F4 MCU, allowing you to run your betaflight/iNav control loop insanely fast.  This gives you the extra edge when racing your FPV quadcopter.The Dragonfly 5.8g stackable VTX comes with 48 channels, 9-26v input and switchable between 25/200/600mw. The stackable design makes you easy to place this VTX above your flight controller. With 48 channels, no need to worry about the interference while powered on any more. We choose Cyclone BLHeli-s to use on the builds. BLHeli-S is still the most stable firmware. We have tested the ESCs, it is powerful enough to run with the included RJX 2205 2300KV motors.The ARF packages come with both 2 blades propellers and 3 blades propellers. The 2 blades props save more power than the 3 blades so that you can fly for a longer time, very suitable for FPV beginners. When you are good at flying, you can change to use the 3 blades propellers.The builds also comes with 700TVL 5-12V Micro FPV Camera to make you can enjoy the FPV racing. In general, these setups are specially made for FPV beginners with a good performance and low cost. They can be flied with full throttle and used for freestyle flying, very suitable for practice.ARF 1 Including:ZMR Eclipse 210mm Carbon Fiber Mini FPV Quadcopter Frame Kit  * 1 setRJX 2205 2300KV Brushless Motors * 4 pcsCYCLONE BLHELI-S 20A ESC * 4 pcsMATEK PDB XT60 with BEC * 1 pcOmnibus F4 V5 Flight Controller * 1 pcDragonFly 5030 Bulletproof Props White * 2 pairs5030 Inch Electric Propeller White * 2 pairsAccessories Bag * 1 setARF 2 Including:ZMR Eclipse 210mm Carbon Fiber Mini FPV Quadcopter Frame Kit * 1 700TVL 5-12V Micro FPV Camera * 1RJX 2205 2300KV Brushless Motors * 4 pcsCYCLONE BLHELI-S 20A ESC * 4 pcsMATEK PDB XT60 with BEC * 1pcOmnibus F4 V5 Flight Controller * 1 pcDragonfly 5.8G 48CH Stackable Video Transmitter * 1 pcDragonfly Transmitting Extension Cables * 1 pcDragonfly Booster 5.8G FPV Antenna 5cm SMA * 1 pcDragonFly 5030 Bulletproof Props White * 2 pairs5030 Inch Electric Propeller White * 2 pairsAccessories Bag * 1 setARF1 Including: ARF2 Including: 

    $110.99-$149.99

    SKU:ZMARF

    Weight: 0.50 kg

  • KISS 32A 32bit 2-6S ESC

    The KISS ESC 32A powered by a M4 MCU is the new member in the KISS family, developed for race copters with power hungry motor/prop combinations. Actively limited to 45A for longevity it comes with all the features of its little brother, the ESC24A re. With a capacitor it can be driven by up to 6s lipos. This ESC is also compatible with Dshot2400 for an incredibly low response time.Features:- 32-Bit-ARM Cortex M4 MCU @ 80 MHz- Telemetry capability (voltage, current, temperature, rpm)- Over current protection (measures the current and reduces it to max 45A)- Over temperature protection (reduces the max power if hotter then 100°C)- sinHybrid :: Sinwave/BackEMF Hybrid Commutation for smoother running.)- Dshot 2400 (Full resolution of 2000 steps takes only 6.5μs).- Supports all common Dshot commands like turtle mode, 3D mode and rotation direction change.- Expanded adaptive auto timing (3,25-30° advance on each commutation),- For Race Multicopters (32A continuous also with weak cooling),High max. RPM (500.000ERpm, 71.400Rpm with a 14Pole Motor) - Small size (19 x 27 mm)- Accurate RPM control (2000 steps using Dshot)- No additional capacitor needed for 3-5S. Add a min. 220μF min. 50V Cap for 6S usage!- Very fast throttle response, Linear throttle response, Active freewheeling (low diode losses)- Regenerative braking 3-6S LiPo Dshot 100-2400, Oneshot42, Oneshot125 and normal (25 – 500Hz) PWM auto detected.- Supports FrSky Sbus, Graupner SumD, TBS CROSSFIRE and Multiplex SRXL, S-Port, Graupner HOTT, TBS CROSSFIRE and Sensorbus- Operating voltage 9 - 30V (3-6s)- Maximum continuous current 32A, instantaneous maximum current 45A, actively limited- 600000 ERPM maximum rotation field speed (useage up to 500000 recommended)Specifications:Current Draw: 32A Continuous (45A Burst)Voltage Range: 2-6s LipoWeight: 3.3gSize: 20mm x 26mm x 4.5mm

    $29.89

    SKU:K32C

    Weight: 0.10 kg

  • Feather SX-220 ARF

    Feather SX-220 FPV Racing QuadFeather SX-220 is a light and durable frame made of Japanese 3K carbon fiber. It features an easily removable camera housing mount that allows the user to access the interior of the frame to preform basic maintenance on electronic components. The side panel camera mounts for your FPV camera can be adjusted from 10-60 degrees to allow for a camera angle that can suit both beginner and experienced pilots. The camera protection housing also works double duty and can be used as a 30 degree mount for you HD action cameras. The interior arm nuts are pressed into the carbon fiber by using pressed nuts we’re able to achieve a simplistic design that looks nice and has a use. The screws for the arm placement can easily be removed and allow for very easy arm removal in the event that one might need to be changed. Feather SX-220 weighs in at 86.5 grams. This includes all bolts, nuts, standoffs and the sma glass fiber antenna mount. Such a light weight will help you shave off plenty of grams in your racing build. Feather SX-220 frame is also our first quad to be backed with a one year warranty against defects and broken parts. Please have a look at our 1 year replacement warranty that protects you from broken carbon fiber that may occur to your quad within it’s first year of use. The SX-220 ARF comes with the powerful Dragonfly Hurricane 2207 2500KV brushless motors which are specially designed for FPV racing. The reputable Omnibus F4 ensures you to fly with the best possible performance, while the Typhoon32 4in1 32bit BLHeli ESC gives you the incredible speed.Features:Made of Ultra High Quality Japanese 3K Carbon Fiber.Camera Angle can be Adjusted Between 10~60 Degree.FPV/Action Camera Mounts.30 Degree Mount for HD Action Cameras.Glass-fiber SMA mount.Turtle mode Compatible.Replaceable Arms for Easy Installing and Reparing.The frame is only 86.5g includes all bolts, nuts, standoffs and the SMA glass fiber antenna mount.Combo Included:1x Feather SX-220 FPV Racing Frame4x Dragonfly Hurricane 2207 KV2500 Brushless Motor1x Typhoon32 4in1 BLHeli_32 ESC 4x35A V1.21x Omnibus F4 V5 Flight ControllerWarranty ClaimsIn the event that breakage does occur, FPV Model is offering a a full coverage warranty on both Carbon Fiber and aluminum stand-offs. In order to process your claim, please send an email to sales@fpvmodel.com. In the email please include the following information: 1.) Your order number. 2.) Your Full Name3.) Pictures of the broken parts with arrows highlighting the problem. Please send pictures of the broken parts. The pictures should show the parts installed on the frame and include a paper note with your order number clearly visible in the photos. Please do not send pictures of parts you may have found on the internet. 

    $159.99

    SKU:SX220ARF

    Weight: 0.50 kg

  • Bardwell F4 Flight Controller - AIO FC BY RDQ W/OSD 3-6S

    Bardwell F4 AIO | JOSHUA BARDWELL FLIGHT CONTROLLERJoshua Bardwell and RaceDayQuads have come together to make the industry’s next favorite flight controller. With the latest features, a layout which will make your build clean and easy, top notch customer support, and an extremely competitive price, the Bardwell F4 AIO Flight Controller is perfect for your quad!Features:3-6s F4, AIO board with MPU 6000 gyroSuperb board layout allowing for easy and clean buildsJoshua Bardwell authored manual and selected features, manufactured and backed by RaceDayQuadsCentrally located gyroBetaflight OSD w/131a current sensorCompact 30.5x30.5 board layout9v filtered power out for VTXs – very strong filtering capability for clean video (the 5v output is also filtered) Power Out: 3x 5v, 1x 3.3v, 1x VBAT, 1x VTX filtered power (7.6v), 1x Camera filtered power (7.6v); 4x UARTS for FRSKY, SBUS, IBUS, SAT (2 inverted UARTS)Smart Audio compatibility and Camera Control capabilityPre-flashed with BF 3.2.1 – Compatible with CLRACINGF4.hexProgrammable LED pinBuzzer pinsBlackbox capabilityNo pinned-connectors – all direct solder for optimal durabilityIncluded and installed vibration dampenersMANUALFor a detailed and complete manual authored by Joshua Bardwell, please click here. If you are using SmartPort Telemetry wired to the TELE pad, you must go into the CLI and type:set tlm_halfduplex = offsaveSETUP TIPS FOR BEST VIDEOWhen setup appropriately, the Bardwell F4 *should* not need any capacitors in order to have clean video. However, on certain setups it will simply be unavoidable. Here are tips on how to setup your board for best video quality and the least likelihood of needing capacitors for perfect video. The general idea is that you want to limit your camera and VTXs exposure to noise. I.E. - you want to limit exposure to your Bardwell F4, since the noise is produced by your ESCs, then passed through the Flight Controller to your VTX AND your Camera. A common misconception is that noise shows itself only through the VTX, when in fact it can be shown to your video via your Camera. So, here are our tips:Can your VTX power your Camera? If yes, power your Camera straight off your VTX 100% of the time. If no, then use the supplied camera power pads on the Flight Controller.If you arent using it, dont wire it! Not using OSD or camera control? Then wire your cameras video straight to your VTX (not through the video pads on the FC) and do not wire the camera control. Now, those two general tips will get you darn close! But what if your video still isnt perfect? Heres what you can do further. First, there are two types of issues. One is noise related, one is power related. Noise looks like clear lines through your video. Power issues look like black lines through your video. For a noise problem, a capacitor will work and you can add it now and ignore the tips below and go fly. For those not wanting to add a Cap or those with a power (black lines) issue, keep reading:I have a noise (clear lines) issue: Follow steps 1 and 2 above. If still noisy (and you dont want to use a cap), then power your camera off of the same pads as your VTX. If this does not work, then your build requires a cap. Kind of a last resort is considering not using OSD or camera control and then wiring appropriately (depends, would you rather no Cap or no OSD in your build?).I have a power (black lines) issue: Your VTX is power hungry! This is a known thing with some VTXs, like the Mach 2 and the Unify series. They simply do not do well under regulated power. You can often confirm this by testing power levels. The issue will be worse at 800mw than 25mw. The only fix is to power your VTX directly off of the battery leads. If this does not remove the black lines, you have a defective VTX or a defective Camera. Wed bet its the Camera that has gone bad before the VTX if you are taking a wild guess. But, if all is good then now you should either A) have clear video or B) have noise (clear lines now instead of black). If you have noise, refer to steps 1 and 2 above. If that does not fix the noise, then your build requires a capacitor.We hope this has been helpful! Any further questions or issues, please contact us.

    $34.99

    SKU:BWF4FC

    Weight: 0.10 kg

  • ZMR Eclipse 210mm Carbon Fiber Mini FPV Quadcopter Frame Kit

    ZMR-X210 is one of the most popular and reputable racing frames of FPV Model. We are always listening to what our customers say, and now here comes a new version - ZMR Eclipse. We have made some slight changes to the ZMR-X210. The new body frame is a bit shorter and remove some unnecessary parts but keep the wheelbase the same as 210mm. Still use the same 3K carbon fiber material that we use on ZMR-X210 and ZMR210R. The weight is about 122 grams only including the hardwares.Ajdustable camera angle design, two kinds of installation methods, suitable for the most common FPV cameras on the market.Another big improvement is that the nuts have already been pressed into the carbon plates, so that it is more convenient to build and also will save some weight.Use countersunk screws on the top plate, it is more stable for the battery to put on it. And there remains two battery strap locations to secure the battery. The distance is more reasonable than the x210.3.5mm bottom plate, the ZMR Eclipse is able to survive from the hardest crashes. The installation for the 4 nylon standoffs is more reasonable comparing to the ZMR-X210.Package included: 1x ZMR ECLIPSE Carbon Fiber Frame4x 4mm Carbon Fiber Arms 1X camera mount1x Board Camera Mount 1x Set of Steel screws, aluminum mounting hardware, and standoffs 2x FPVModel velco strap1x 2mm top plate 2x 3.5mm lower platesWeight: 122 grams (Frame and hardware totally ) We have made some slight changes to the ZMR-X210. The new body frame is a bit shorter and remove some unnecessary parts but keep the wheelbase the same as 210mm. Still use the same 3K carbon fiber material that we use on ZMR-X210 and ZMR210R. The weight is about 122 grams only including the hardwares.Ajdustable camera angle design, two kinds of installation methods, suitable for the most common FPV cameras on the market.Use countersunk screws on the top plate, it is more stable for the battery to put on it. And there remains two battery strap locations to secure the battery. The distance is more reasonable than the x210.Another big improvement is that the nuts have already been pressed into the carbon plates, so that it is more convenient to build and also will save some weight.3.5mm bottom plate, the ZMR Eclipse is able to survive from the hardest crashes. The installation for the 4 nylon standoffs is more reasonable comparing to the ZMR-X210.

    $39.99

    SKU:ZMREF

    Weight: 0.50 kg

  • Typhoon32 4in1 BLHeli_32 ESC 4x35A V1.2

    4in1 ESC with 30.5x30.5 mm Mounting holes, supports DSHOT 1200, BLHELI32 firmware.Features:32bit ESC with BLHELI32 firmwareSupports 3-4S lipo input4PWM inputVoltage output (VBAT)NO BECSupports oneshot / Multishot / Dshot PWMMounting holes 30.5x30.5mmSupports damped lightExternal capacitors neededPackage Included:4in1 ESCCapacitoDifferent frame will cause different test result with the current, we rated it as the mid-value, in your frame, the current may higher or lower, there is no Guarantee, if you can get same result in your frame.Notice: There is NO CABLE included.

    $59.99 $53.99, Save 10% OFF

    SKU:T32C2

    Weight: 0.10 kg

  • X-Racer KL100 Micro Racing Quad ARF / BNF

    Note: The battery and Frsky XM Receiver that showed in above video are not included.Micro class FPV racing has been more and more popular around the world, you can enjoy the fun of FPV racing with those micro racers anywhere, anytime. Now here comes a new micro racing frame KL100.KL100 is a 2” propeller 100mm class micro frame. Only about 101 grams with a 2S 550mAh lipo battery, 5 grams lighter than the popular 90mm KL-EX90. The small size and light weight do not mean that the KL100 is lacking power. In fact, as per our internal tests, with just a 2S battery, it is powerful enough to give you a super fast respond. You can feel the power just like you are flying with a 5” racing quad.The KL100 BNF/ARF are equipped with the very accepted Gemfan 2035BN propellers and use the new EMAX F3 Magnum mini FPV tower system which incorporates Betaflight OSD, F3 FC and 3-4s 4in1 ESC. The same to KL-EX90, the Dragonfly MC1105 7500kv motors have been getting rave reviews and are also used on the build. We don’t stop there though. We are cooperating with Runcam, using the new Runcam Nano FPV camera and RunCam TX200 5.8G 48CH Video Transmitter on the build. The Runcam Nano is the smallest Runcam FPV camera so far yet it has a very fast exposure handling (see the review by Oscar Liang). It is a camera Runcam specially made for nano racing quads that has the same performance to reputable Runcam Swift / Swift Mini. The Runcam TX200 is super light in weight and easy to control. It has a better reception than the 25mw vtx. Features:1. 100mm micro class with 2” propellers. Do not need to get it registered with the FAA if you are from the United States.2. Small in size and light in weight, all up weight 66 grams only without battery and about 101 grams with a 2S 550mAh lipo.3. Powerful and super fast respond with 2s lipo. Capable of running with 3s by using 6000kv motors (coming soon).4. Uses reputable EMAX F3 Magnum mini FPV tower system with built-in Betaflight OSD gives you an extremely good stability and flight performance.5. Equipped with powerful MC1105 brushless motors and Gemfan 2035BN propellers.6. Uses Runcam Nano FPV camera and Runcam TX200 vTX.Before Purchasing: We send the green version of 3D printed part in the ARF/ BNF combo if without special instructions. If you prefer another color (the 3D printing parts have color green and blue), please let us know by leaving message at the checkout page.The KL100 does not come with the receiver as some of you may use different transmitter. If you are using the Frsky transmitter, we suggest use FrSky XM 16 Ch Micro SBUS Receiver. If you are using other RC transmitters, you will use other mini transmitters accordingly.The camera in this combo is in PAL version. If you need the NTSC version, please leave message at checkout, thank you.Brief Tutorial of X-Racer KL100 Racing Quad

    $139.99-$149.99

    SKU:KL100ARF

    Weight: 0.40 kg

  • X-Racer KL100 Micro Racing Quad Frame Kit

    Micro class FPV racing has been more and more popular around the world, you can enjoy the fun of FPV racing with those micro racers anywhere, anytime. Now here comes a new micro racing frame KL100.KL100 is a 2” propeller 100mm class micro frame. Only about 101 grams with a 2S 550mAh lipo battery, 5 grams lighter than the popular 90mm KL-EX90. The price is for KL100 frame kit only. We suggest use the same equipment as we are using for KL100 BNF and KL100 ARF. The KL100 BNF/ARF are equipped with the very accepted Gemfan 2035BN propellers and uses the new EMAX F3 Magnum mini FPV tower system which incorporates Betaflight OSD, F3 FC and 3-4s 4in1 ESC. The same to KL-EX90, the Dragonfly MC1105 7500kv motors have been getting rave reviews and are also used on this frame. By using the suggested build, as per our internal test, with just a 2S battery, it is powerful enough to give you a super fast respond. You can feel the power just like you are flying with a 5” racing quad.If you are not sure what to build the X-Racer KL100. You can take a reference to what are included in the ARF and BNF version: https://www.fpvmodel.com/x-racer-kl100-micro-racing-quad-arf-bnf_g1380.html. If you are using the setup as we recommend here, you can also take a reference to the build video below.Features:100mm micro class with 2” propellers. Do not need to get it registered with the FAA if you are from the United States.Small in size and light in weight, all up weight 66 grams only without battery and about 101 grams with a 2S 550mAh lipo.Powerful and super fast respond with 2s lipo. Capable of running with 3s by using 6000kv motors (coming soon).Durable 3k carbon firber material. No need to worry about the crash.Recommended Builds (Not Included):EMAX F3 Magnum mini FPV tower systemDragonfly MC1105 7500kv motorsGemfan 2035BN propellersRuncam Nano FPV CameraAomway TX004 VtxBrief Tutorial of X-Racer KL100 Racing Quad

    $16.99

    SKU:KL100F

    Weight: 0.30 kg

  • Aomway TX004 Mini 5.8G 25mw/100mw/200MW Power Switchable Transmitter

    TX004 Transmitter is a 5.8G ISM band simulation diagram transmitter with a stable output power, long-distance transmission,  powerful filter. Can guarantee the image of the maximum throttle no snow, no stripes and so on. TX004 transmitter also has the funtion of remote control the OSD interface and support for more than 8 peoples at the same time flying.Features:-Output power is stable, long-distance transmission: ≥0.5km@25mW, ≥0.8km@100mW, ≥1km@200mW (Original antenna)-Transmit power 4 block switch: 0mW/25mW/100mW/200mW-64 frequency output, has E group of eight competition frequency at the same time without interference-Fast frequency lock-With self-test output power-Video format: NTSC /PAL-Wide input voltage range, low power consumption: 7V~24V,+12V/170mA@200mW.-Small volume: 27mm×27mm×4.5mm-Light weight: ≤3g (Do not including the antenna)Frequency Table:

    $16.99

    SKU:AWTXT

    Weight: 0.10 kg

  • DALRC ENGINE 40A 3-5S 4IN1 ESC BLheli32 DShot 1200

    DALRC ENGINE 40A 4IN1 ESC adapted 32bit high quality MCU which features more rapidly responeding speed, even smoother handing experience, excellent hardware design with high quality component ensured the powerful performance of ESC, bring you enjoyable flying experience!Features:- Adapting STSPIN32FOA 32 bit burshless motor dedicated high quality processing chip,maximum processing frequency reached to 48MHZ;- Adapting 55 pieces TDK 22UF 25V Low ESR capacitance,total capacity reached to 1150 UF,even lower ripple and higher stability;- Top grade import MOS tube;- 3OZ copper PCB,better operating load capacity;- Up to 5V/3A BEC output.Specification:Item Name: CNC Radiatior DALRC ENGINE 4IN1 ESC Usage: Spare Part for Racing Drone QuadcopterSize:36*36*6mmHole to hole distance:30.5*30.5mm/Φ4.0Weight:16gContinuous Current:40ABurst current(10S):50AInput Voltage:3-5S LipoMcu:STSPIN32FOABEC:5V 3ACapacitance:1150UF Low ESRFirmware:BLHELI 32.XSupports:DShot 300-1200/MultiShot/PWM/OneShotCurrent Sensor: Support

    $56.99

    SKU:D40ESC

    Weight: 0.10 kg

  • RaceFlight Revolt Flight Controller V3

    The RaceFlight Revolt flight controller is the most advanced, performance driven, flight controller ever designed. The Revolt uses a powerful F405 MPU, accompanied with the High Speed Invensense 20602 gyro, allows it to take full advantage of RaceFlight Ones efficient code to run at 32KHz for the best Performance possible.PerformanceThe Revolt presents not only the BEST performance, but also the most STABLE performance due to the amazing vibration rejection technology implemented in RaceFlight. Our filters along with the integrated RaceFlight Gummies, allow your quad to stay in the air no matter what! Damaged propellers caused by that insane gate clip on turn 3? Not a problem. You can still finish the race! Endless days of tuning are now a thing of the past. Our boards come preloaded with software and defaults that should fly amazing for 99% of people.In addition to the vibration rejection technology, the SSG (Invensense 20602) gives you the highest speeds currently possible with the lowest noise floor and highest sensitivity. The Invensense 20602 gyro has never been used in any flight controller before (except the Revolt) and gives you the fastest response time possible as if the quad can read your mind.Setup SimplicitySetting up the Revolt is easy. The solder pin layout is easy to read with motor connections in each corner. Just solder the closest motors and the wizard handles the rest, you can put the Revolt in upside down and backwards just solder to the closest motor pad and the RF1 wizards will handle the rest. . The Millivolt also features DFU free updating and a self-healing and updating bootloader, just in case something does go wrong.Zadig and other complicated driver configuration tools are a thing of the past with the Revolt’s new driverless installation technology. Tired of messing around with Zadig or DFU to your software? We were too, that’s why you no longer have to worry about messing around with them. The Revolt also features DFU free updating and a self-healing and updating bootloader, just in case something does go wrong.FeaturesLED Driver for WS2812b programmable LEDSBUS InversionHigh Speed 32khz gyro, lowest noise floor and highest sensitivity gyro ever usedThrough hole solder pads – forms an I-Beam when soldered for extra strengthFrSky Taranis, Spektrum, Futaba, JR, IBus, Sbus and other radio supportIntegrated buzzer driverVoltage and current ADC pins, for full voltage and current monitoringFull telemetry output supportESC flashing and configuration built into configuratorMost active software developmentSelectable 3.3 voltage3 serial uartsBluetooth expandableF4 processor16mb of flash memoryGPS expandablePins into RaceFlight Bolt 4in1 ESCDimensions: 36mm x 36mmMounting holes: 30.5mm squared to center of holesWeight: 6 gramsEasily connectable to the RaceFlight Bolt with our special connector.The RaceFlight GuaranteeRevolters will also get access to RaceFlight’s ticketed tech support which will include step-by-step help with installation, tuning, and anything else that may arise with your Revolt.

    $41.88

    SKU:RFRV3FC

    Weight: 0.10 kg

Find us on Google+ Watch us on Youtube Like us on Twitter Follow us on Facebook

Home   |   About Us   |   New Products   |   Multi-Rotors   |   FPV Airplanes   |   FPV Equipment   |   Battery / Chargers   |   Tools & Accessories   |   Contact Us   |   Blog   |  Site Map

Product Tags: ABCDEFGHIJKLMNOPQRSTUVWXYZ0-9

Copyright © 2015 FPVMODEL.COM®. All Rights Reserved.