Sorted:
  • Acro Naze32 Flight Controller Board by AbuseMark (Rev.6)

    Naze32 is back with a brand new revision and its sure to keep you at the top of your game. STM32F103CBT6 32-bit ARM Cortex M3 processor (72MHz, 3.3V)Invensense MPU6500 MEMS accelerometer + gyroBMP280 BarometerBuilt-in Micro-USB for programming/firmware update36x36mm size, 5 gram weight w/o headersMade in JAPANShipping with 16V input capable voltage regulatorsThese come with pin headers (straight and right angle options), NOT soldered to the board. Naze32 rev6 Features:    USB on right side    PPM/PWM input as through-hole    3.3V, I2C on standard-size headers    Fully pinout compatible with rev5 accessories (OSDoge etc)    SBUS Inverter    Spectrum satellite    MPU6500    Sonar pads w/resistors added for direct connection to 5V sonar    All extra pads (FT, GP, A5) on top, only sonar on bottom    BMP280 barometer    16mbit flashSpecs:    36x36 mm (30.5mm Mounting)    5.3 grams (no headers, 7.3 grams with)    2000 degrees\second 3-axis MEMS gyro + accelerometer (MPU6500)    Input voltage: Max 16V on input rail and up to 35V 6s on the voltage sense lineIncluded: 1x  Acro Naze32 rev6 1x  pin header 1x  Breakout cable Attention (Update on 10/15/2015): Naze32 Rev 6 flight controllers are a new design and some changes have been made that are different from the Rev 5 flight controller. Please keep in mind that when the board is connected to a fully assembled multi rotor a direct connection to USB port on a computer can supply the entire multi rotor with 5 volts of power, please pay attention and make sure all parts are connected properly. Update on 09/21/2015: The Naze32 now has been upgraded from Reversion 5 to Reversion 6This product has different colors (white, red, black and blue), and we will ship it to you with the color at random. Before purchasing, please make sure you accept this. Thank you!

    $15.60

    SKU:NAZE32-A+C

    Weight: 0.10 kg

  • Feiyu FY 41AP-M&GPS Autopilot For Multi-rotors

    Product DescriptionSuppliers:FeiYu-TechPacking Weight:0.3 kgSingle Weight:0.022 kg  Brief Introduction       FY-41AP is an inertial attitude measurement instrument used for FPV flight on fixed-wing aircrafts and multi-rotors aircrafts. It has an integrated OSD video overlay system that presents critical flight information such as power management, airspeed, altitude, and flight direction via its electronic compass, allowing for a clear visual flight while ensuring key information is within sight.       Flight stabilization is achieved via an integrated 3 axis gyro, 3 axis accelerometer, 3 axis magnetometer and a barometric pressure sensor. This enables the module to accurately measure flight attitude, earth azimuth & relative altitude to achieve: Function Introduction    ●Attitude Stabilized Mode - FY-41AP-M can auto stabilize the aircraft flight attitude in this mode, pitch and roll stick center position for 0 °attitude,its endpoint is 35 ° . Yaw stick in the center position will lock current course , its endpoint corresponding maximum rotation rate 135 ° per second, Throttle stick direct control aircraft climb and decline, climbing and declining rate is directly related to the throttle.    ●Hovering Mode - In this Mode, without GPS location, auto locks the altitude, in maximum means climb rate is 3 m/s, in minimum means decline rate is 1.5 m/s.The GPS Module must be connected .When the GPS is connected and at least 5 GPS satellites detected,when Pitch, roll sticks released will lock the new position.    ●Auto Return To Home Mode - The GPS Module must be connected to the DoS with at least 5 GPS satellites detected.In this Mode,will auto return to home points and auto landing.    ●Camera Gimbal Stabilization - FY-41AP multi-rotor firmware,when is used to control the aircraft under 6 axis, can simultaneously control two axis Camera Gimbal Stabilization.     > Related download for multi-rotors :         >> FY-41AP firmware for multi-rotors V2.30 : Download  |  More information of this firmware           >> FY module firmware upgrade software and manual : Download        >> The latest FY-DOS&41AP-SETTING software V1.2 for multi-rotors : Downlad        >> FY-41AP Manual for Multi-rotor :   Read online  |   Download         More FY-41AP related downloads: Click in OSD Video Overlay System Function    ● First Person View (FPV) - FY-41AP has an integrated OSD video overlay system that presents critical flight information on the video for easy enjoy FPV, at the same time, Auto stable, Fixed altitude & Heading lock, Waypoint Navigation , Auto Return To Home function will make FPV operation more easy.        OSD is an essential part for FPV. The FY-41AP can adapt both PAL and NTSC video signals. The entire adaptive process is completed approximately within 1 second.        Integrated OSD Video Overlay System, FY-41AP overlays flight telemetry information onto video image. Information displayed includes: Altitude, Speed, Direction, Home Direction and many more. FY-41AP OSD display part firmware V1.13 : DownloadFY module firmware upgrade software and manual : Download quickly  |  DownloadFeiyu tech kindly remind you: You should to do the firmware upgrade separately for FY-41AP-OSD control module and OSD module. UART2 is the interface connects to the PC computer serial port to do the firmware upgrade for FY-41AP OSD module.If you want to upgrade the firmware of  flight control part ,please click on hereBasic PerformanceSupported Multi-rotors:Quadcopter I4, X4 / Hexacopter I6, X6, IY6, Y6/Octocopter  I8,  X8Supported ESC output:400Hz refresh frequencyRecommended Transmitter: PCM or 2.4GHz with minimum 6 channelsFY-41AP Module Working Voltage: 5.3V@0.2A( Powered by Power Manager)Power Manager:          Working Voltage Range: Power of battery 7~26V (2S ~ 6S)          Measuring current:0~100A          Power for FY-41AP module:5.3V@2A          Power for Video transmission system :12V@2AOperating Temperature: -10°C ~ 50°CAssistant Software System Requirement: Windows XP sp3 / Windows 7 / Windows 8 Flight PerformanceHovering Accuracy :Vertical:±0.8m,Horizontal:±2.5m (GPS Mode)Max Yaw Angular Velocity:150°/sMax Tilt Angle:35°Ascent / Descent:-1.5m/s ~ +3m/s Hardware● Weight&Dimensions:FY-41AP: 34g (58×37×19mm);GPS :24g (32×32×13.5mm);Power Manager:35g(50×24×18mm).Note: the red vibration absorbing mount is not included.   GCS ground station software, used to set the flight parameters, mission planning, monitoring in flight. Software integration of electronic map function can through the map software () the Google earth live map out into the GCS software. The main function is    Parameter Settings — Control parameters setting, course setting, etc    Real time monitoring — It can monitor flight attitude. And via the GCS software you can change the flight altitude in real time and realize the mouse click flight.    Record and monitoring flight —You can monitor and download flight path via the GCS software in your computer.GCS 5.1 Software:   Download quickly   |  DownloadNote: Before using FY GCS above 4.11 version, please make sure that the firmware of FY-41AP is the latest version!More versions of the GCS software, please   click in

    $235.00 $197.40, Save 16% OFF

    SKU:FY41AP-M

    Weight: 0.40 kg

  • New Naza-M Lite Multi-rotor Flight Control System with GPS Compass BEC LED Module

      For entry-level enthusiasts, DJI now brings out the most cost-effective solution, the NAZA-M Lite flight control system. As the simplified version of NAZA-M, it inherits the high reliability and stability of NAZA-M. The innovative All-in-one design simplifies installation and saves space and weight. It contains inner damping, controllers, 3-axis gyroscope, 3-axis accelerometer and barometer in its light and small Main Controller. It can measure flying altitude, attitude and therefore can be used for autopilot/automatic control.All-in-One DesignFor entry-level enthusiasts, DJI now brings out the most cost-effective solution, the NAZA-M Lite flight control system. As the simplified version of NAZA-M, it inherits the high reliability and stability of NAZA-M. The innovative All-in-one design simplifies installation and saves space and weight. It contains inner damping, controllers, 3-axis gyroscope, 3-axis accelerometer and barometer in its light and small Main Controller. It can measure flying altitude, attitude and therefore can be used for autopilot/automatic control.Advanced attitude stabilize AlgorithmThe advanced attitude stabilization algorithm not only inherits the outstanding flight stability of DJI products, but also provides excellent maneuverability. It is more flexible and stable, and gives the hobbyists a wonderful flight experience.Multiple flight control mode/intelligent switchingIt offers three types of control modes: GPS Atti. Mode (with GPS module), Atti. Mode, Manual Mode. The pilot can switch between the three modes to achieve different flight characteristics. It also can adjust automatically within the flight environment and intelligently switch between GPS Atti. Mode and Atti. Mode to make sure the flight is safe and secure. .GPS Module Available/Accurate Position holdThe plug and play GPS module will greatly enhance the performance for Aerial Photography with accurate Position Hold, Return-To-Home and Intelligent Orientation Control functionalities. With the GPS Module, the multi-rotor will have position and altitude locked accurately even in windy conditions. Hovering accuracy is approximately 2.5m horizontal and 0.8m vertical.Intelligent Orientation Control (IOC)Usually, the forward direction of a flying multi-rotor is the same as the nose direction. By using Intelligent Orientation Control (IOC), wherever the nose points,the forward direction has nothing to do with nose direction:In course lock flying, the forward direction is the same as a recorded nose direction. See the following figures(Mode 1):In home lock flying, the forward direction is the same as the direction from home point to multi-rotor.See the following figures (Mode 2):Failsafe modeIf your transmitter supports failsafe, then you can set failsafe through port-U. Naza controller has built-in auto level failsafe function, which means when the communication between MC and the transmitter is disconnected, the outputs of all command sticks from controller will go to center position. If the GPS module is used, you can also set RTH on failsafe. If your transmitter has only 4 channels, then MC will work in Atti. Mode by default without the failsafe function.Low voltage protectionIn order to prevent your multi-rotor from crashing or other harmful consequences caused by low battery voltage, we have designed two levels of low voltage protection. You can choose not to use this, however we strongly recommend you to enable the protection. Both levels of protection have LED warning as default. The first level will blink the red light continuously; the second level will blink red light continuously and the multi-rotor will descend and land. In manual mode when low voltage protection is triggered the LED warning will be active only.Motor Arm and Motor Dis-armThere are four ways to start the motors, see the following picture:When you want to start the multi-rotor, you need to perform any of the ways of CSC. During the flight, if the motors stop, you can immediately execute the CSC and the motors will start. This enhances the safety of the multi-rotor; no uncontrolled starting of the motors. Motor Disarm: There are two modes of Motor Disarm: namely Intelligent Mode and Immediate Mode. For more information, please refer to the user manual or DJI Wiki.Support Futaba S-Bus and PPM receiverMinimum Four channel receiver supported, also PPM and Futaba S-Bus receiver supported.PPM & S-Bus receivers (the general use of the first 8 channels of S-Bus receiver) to optimize the channel connection, the A, E, T, R, U five-channel functions are set using channel X2, use only one servo cable to connect the PPM or S-Bus to X2, this makes installation quick and easy, not easy to make mistakes.Supported multi-rotor typesNaza-M Lite now supports six types of multi-rotor, which meets the different needs of the enthusiasts.Quad I, Quad X;Hexa I, Hexa V, Hexa Y, Hexa IY;Built-in Gimbal stabilization functionThe gimbal stabilization module is compatible with almost all 2-axis gimbal systems. The system will adjust the gimbal and camera according to the attitude of the aircraft after setting the parameters the first time.Remote adjustmentThe default parameter settings are OK for you to achieve a normal flight, and it also supports remote parameter adjustment by using a control slider on the TX during flight, in order to obtain better performance. For all the product info and support, please check here:http://www.dji-innovations.com/tutorial/naza-m-lite-tutorials-en/

    $162.99 $78.24, Save 52% OFF

    SKU:NAZA-MLITE

    Weight: 0.50 kg

  • Tarot 3-axis Pan Tilt and roll stabilization Gyro system ZYX-GS

    Product Description Features:● Three axis stabilization. Pan, Tilt and roll stabilization● Adjustable Gains and 3D attitude through PC software● Support attitude locking mode and attitude following mode● Support stick following mode and position following mode● Sensor technology: 3-Axis MEMS gyro and accelerometer● Support servo type: 1520/960/760 analog servo and 1520/960/760 digital servo● Support receiver type: standard receiver/S-BUS receiver/DMS digital receiver● Support remote controller type: PPM/PCM/2.4G Specification:● Size: 38x29x13mm/27x27x9mm● Weight: 26g (without wires and connectors)● Support receiver: PPM/PCM/2.4G● Operating voltage: DC3.5V~9V● Operating current: 60mA● Working temperature: -15oC~65oC● Max palstance: 2000o/sec● Max acceleration: 16g.● Frequency: 800Hz● Control angle: -45o~45o(roll), -180o~180o(direction), -135o~90 o(pitch)

    $135.90 $97.85, Save 28% OFF

    SKU:TRPTRGYRO

    Weight: 0.40 kg

  • DJI A2 Flagship Multirotor Stabilization Controller Flight Control with GPS Pro Combo(free shipping)

    DJI A2 Flagship Multirotor Stabilization Controller Flight Control with GPS Pro ComboDJI A2 Flagship Multirotor Stabilization Controller Flight Control with GPS Pro Combo This just in! DJi releases its new flagship MR controller the A2!DJI is pleased to announce a new flagship multirotor controllerm its called the A2". superseding the Wookong family, the A2 sticks closely to the DJIs tradition of wowing customers with high specs, but it also innovates dramatically in a couple of key areas, which DJI hopes will give it an edge over the competition.DJI A2 Multi-Rotor stabilization controller is a complete flight system for various multi-rotor platforms for commercial and industrial AP applications. Based on the technology and design philosophy of DJI’s Ace series of high-performance controller, the A2 offers you a brand new flight experience. Its flight mode setup provides a seamless transition for current Ace One AP professionals. It utilizes high quality components precisely calibrated with temperature compensation in all gyros and sensors, industry renowned flight algorithm in autopilot and UAV field.Specifications:- Flight controller: 54x39x14.9mm- IMU: 41.3x30.5x26.3mm- GPS Pro:62mm(diameter)x14.3mm- PMU: 39.5x27.6x9.8mm- LED-BTU-I: 30x30x7.9mm Learn more: click here

    $1,299.00 $1,130.13, Save 13% OFF   

    SKU:DJA2

    Weight: 1.00 kg

Find us on Google+ Watch us on Youtube Like us on Twitter Follow us on Facebook

Home   |   About Us   |   New Products   |   Multi-Rotors   |   FPV Airplanes   |   FPV Equipment   |   Battery / Chargers   |   Tools & Accessories   |   Contact Us   |   Blog   |  Site Map

Product Tags: ABCDEFGHIJKLMNOPQRSTUVWXYZ0-9

Copyright © 2015 FPVMODEL.COM®. All Rights Reserved.