Sorted:
  • BetaflightF4 Flight Controller

    BetaflightF4 How to ESC Telemetry, Smart Port Audio, Smart Port TelemetryFriendly Reminder: Upon receiving your FC, please connect to USB and calibrate before continuing to build and solder to it.  BetaflightF4 is the follow up design to the very popular BetaflightF3. Following in the same path as Betaflight F3 we have kept a very similar footprint in terms of design with a few added modifications. The F405 has replaced the F303 to allow for lower CPU loads.We have eliminated the 5v/3.3v jumper and added two seperate connection points, one for sbus and one for spektrum users. The jumper still remains for the battery voltage/5v connection for connecting your camera. While wiring the board it is recommended to get power for your vtx either from a different 5v source on the board or if using a higher voltage vtx power it from the battery input coming into the pdb. Running ground loop at Agnd with gnd wires from camera and vtx is still recommended to give the cleanest video signal. Another small design change to this board was changing the BEC, this change takes the recommended 5v 2A current limit and drops it down to 5V 1.5A, its a small change but one that we opted for in order to use a more reliable BEC.BetaflightF4 now comes with telemtry pads for BLHeli32 ESCs these pads are located between the signal and gnd pads for the ESC connections.FeaturesIntegrated PDBBuilt in OSD customizable via Betaflight OSDCurrent sensorIntuitive layoutFlash memory for blackboxTailored to support BetaflightWhen running 8K/8K, CPU usage remains lowSpecificationsF405 ProcessorMPU6000 Gyro/ACC SensorBEC Max current 5V 1.5ABuilt in OSD – configurable via Betaflight GUICurrent sensorPower distribution board with six-layer PCBOSD Max Current: 145AWiring Diagram - Click to enlarge!BetaflightF4 Connection Plan by Phillip SeidelBetaflightF4 Turtle Mode SettingBetaflightF4 OSD FlashingHow to Use ESC TelemetryBetaflightF4 Can not ArmHow to Use Smart Port TelemetryHow to Use BetaflightF4 IBUSThe Number of “Scale the Output Voltage to Miliamp” in BetaflightHow to Set Tramp HV VTXIf you are meeting a problem with the use of flight controller and can not find the answer, please submit your question.

    $44.73 $33.99, Save 24% OFF 3

    SKU:BFF4

    Weight: 0.10 kg

  • Bardwell F4 Flight Controller - AIO FC BY RDQ W/OSD 3-6S

    Bardwell F4 AIO | JOSHUA BARDWELL FLIGHT CONTROLLERJoshua Bardwell and RaceDayQuads have come together to make the industry’s next favorite flight controller. With the latest features, a layout which will make your build clean and easy, top notch customer support, and an extremely competitive price, the Bardwell F4 AIO Flight Controller is perfect for your quad!Features:3-6s F4, AIO board with MPU 6000 gyroSuperb board layout allowing for easy and clean buildsJoshua Bardwell authored manual and selected features, manufactured and backed by RaceDayQuadsCentrally located gyroBetaflight OSD w/131a current sensorCompact 30.5x30.5 board layout7.6v filtered power out for VTXs – very strong filtering capability for clean video (the 5v output is also filtered) Power Out: 3x 5v, 1x 3.3v, 1x VBAT, 1x VTX filtered power (7.6v), 1x Camera filtered power (7.6v); 4x UARTS for FRSKY, SBUS, IBUS, SAT (2 inverted UARTS)Smart Audio compatibility and Camera Control capabilityPre-flashed with BF 3.2.1 – Compatible with CLRACINGF4.hexProgrammable LED pinBuzzer pinsBlackbox capabilityNo pinned-connectors – all direct solder for optimal durabilityIncluded and installed vibration dampenersMANUALFor a detailed and complete manual authored by Joshua Bardwell, please click here. If you are using SmartPort Telemetry wired to the TELE pad, you must go into the CLI and type:set tlm_halfduplex = offsaveSETUP TIPS FOR BEST VIDEOWhen setup appropriately, the Bardwell F4 *should* not need any capacitors in order to have clean video. However, on certain setups it will simply be unavoidable. Here are tips on how to setup your board for best video quality and the least likelihood of needing capacitors for perfect video. The general idea is that you want to limit your camera and VTXs exposure to noise. I.E. - you want to limit exposure to your Bardwell F4, since the noise is produced by your ESCs, then passed through the Flight Controller to your VTX AND your Camera. A common misconception is that noise shows itself only through the VTX, when in fact it can be shown to your video via your Camera. So, here are our tips:Can your VTX power your Camera? If yes, power your Camera straight off your VTX 100% of the time. If no, then use the supplied camera power pads on the Flight Controller.If you arent using it, dont wire it! Not using OSD or camera control? Then wire your cameras video straight to your VTX (not through the video pads on the FC) and do not wire the camera control. Now, those two general tips will get you darn close! But what if your video still isnt perfect? Heres what you can do further. First, there are two types of issues. One is noise related, one is power related. Noise looks like clear lines through your video. Power issues look like black lines through your video. For a noise problem, a capacitor will work and you can add it now and ignore the tips below and go fly. For those not wanting to add a Cap or those with a power (black lines) issue, keep reading:I have a noise (clear lines) issue: Follow steps 1 and 2 above. If still noisy (and you dont want to use a cap), then power your camera off of the same pads as your VTX. If this does not work, then your build requires a cap. Kind of a last resort is considering not using OSD or camera control and then wiring appropriately (depends, would you rather no Cap or no OSD in your build?).I have a power (black lines) issue: Your VTX is power hungry! This is a known thing with some VTXs, like the Mach 2 and the Unify series. They simply do not do well under regulated power. You can often confirm this by testing power levels. The issue will be worse at 800mw than 25mw. The only fix is to power your VTX directly off of the battery leads. If this does not remove the black lines, you have a defective VTX or a defective Camera. Wed bet its the Camera that has gone bad before the VTX if you are taking a wild guess. But, if all is good then now you should either A) have clear video or B) have noise (clear lines now instead of black). If you have noise, refer to steps 1 and 2 above. If that does not fix the noise, then your build requires a capacitor.We hope this has been helpful! Any further questions or issues, please contact us.

    $34.99

    SKU:BWF4FC

    Weight: 0.10 kg

  • RaceFlight Revolt Flight Controller V3

    The RaceFlight Revolt flight controller is the most advanced, performance driven, flight controller ever designed. The Revolt uses a powerful F405 MPU, accompanied with the High Speed Invensense 20602 gyro, allows it to take full advantage of RaceFlight Ones efficient code to run at 32KHz for the best Performance possible.PerformanceThe Revolt presents not only the BEST performance, but also the most STABLE performance due to the amazing vibration rejection technology implemented in RaceFlight. Our filters along with the integrated RaceFlight Gummies, allow your quad to stay in the air no matter what! Damaged propellers caused by that insane gate clip on turn 3? Not a problem. You can still finish the race! Endless days of tuning are now a thing of the past. Our boards come preloaded with software and defaults that should fly amazing for 99% of people.In addition to the vibration rejection technology, the SSG (Invensense 20602) gives you the highest speeds currently possible with the lowest noise floor and highest sensitivity. The Invensense 20602 gyro has never been used in any flight controller before (except the Revolt) and gives you the fastest response time possible as if the quad can read your mind.Setup SimplicitySetting up the Revolt is easy. The solder pin layout is easy to read with motor connections in each corner. Just solder the closest motors and the wizard handles the rest, you can put the Revolt in upside down and backwards just solder to the closest motor pad and the RF1 wizards will handle the rest. . The Millivolt also features DFU free updating and a self-healing and updating bootloader, just in case something does go wrong.Zadig and other complicated driver configuration tools are a thing of the past with the Revolt’s new driverless installation technology. Tired of messing around with Zadig or DFU to your software? We were too, that’s why you no longer have to worry about messing around with them. The Revolt also features DFU free updating and a self-healing and updating bootloader, just in case something does go wrong.FeaturesLED Driver for WS2812b programmable LEDSBUS InversionHigh Speed 32khz gyro, lowest noise floor and highest sensitivity gyro ever usedThrough hole solder pads – forms an I-Beam when soldered for extra strengthFrSky Taranis, Spektrum, Futaba, JR, IBus, Sbus and other radio supportIntegrated buzzer driverVoltage and current ADC pins, for full voltage and current monitoringFull telemetry output supportESC flashing and configuration built into configuratorMost active software developmentSelectable 3.3 voltage3 serial uartsBluetooth expandableF4 processor16mb of flash memoryGPS expandablePins into RaceFlight Bolt 4in1 ESCDimensions: 36mm x 36mmMounting holes: 30.5mm squared to center of holesWeight: 6 gramsEasily connectable to the RaceFlight Bolt with our special connector.The RaceFlight GuaranteeRevolters will also get access to RaceFlight’s ticketed tech support which will include step-by-step help with installation, tuning, and anything else that may arise with your Revolt.

    $41.88

    SKU:RFRV3FC

    Weight: 0.10 kg

  • Emax F3 Magnum Mini Tower System Bullet 12A 4 in 1 ESC And F3 Flight Controller

    EMAX “F3 MAGNUM MINI” FPV TOWER SYSTEM Designed for high performance Micro FPV racers, the F3 Magnum Mini packs in a F3 processor, Betaflight OSD and 12A 4 in 1 ESC that can handle up to 4s batteries. MPU6000 gyro is a proven performer for stable flight and resistance to vibration noise.The FC and ESC with neatly stack together with pinned interconnects that make your build easy to assemble and cleaner looking. This tightly pre-assembled package will fit any frame that has 20 x 20mm mounting hole spacing. The F3 Magnum Mini is the fastest way go from starting a new micro build to FPV Flight!4 in 1 Main Board - F3 FC + Betaflight OSD + 5v Regulator + Buzzer  The heart of the flight control systems is a powerful STM32F303 MCU and MPU6000 gyro flashed with Betaflight for proven rocksteady flight stability. The integrated 5v/3A voltage regulator means clean power for all the FC/OSD components and other attached boards such as VTX, RX and FPV Camera. Betaflight OSD with easily customizable layout of vital flight information and ability to change FC flight parameters. On board buzzer for battery level warning or lost model finder functions.

    $45.99

    SKU:EMF3MT

    Weight: 0.15 kg

  • KISS FC V2 - 32bit F7 Flight Controller

    *** FPV Model is an authourized dealer of FLYDUINO KISS. Genuine KISS flight controller guaranteed.Before Purchasing: Please keep the packaging after receiving KISS flight controller. Each genuine KISS FC has a unique serial number on the packaging, while fake KISS FC does not and can not be activated. Flyduino, the designer and manufacturer of Kiss FC, will offer the technical support only to the ones with serial numbers. If the packaging is lost, you may fail to get the technical support from Flyduino in time. Besides, for any return of KISS products, you will need to send back the KISS packaging as well.Finally Flyduino release the KISS V2 flight controller with a F7 processor. As an authourized dealer of Flyduino, FPV Model is one of the first to receive the FCs. A new simplified Flight controller, the KISS FC V2 includes a complete own Flight Control Firmware development. The Idea was to get the simple KISS FC to the next level and due to intensive long term tests of some pretty good Pilots we were able to optimize the code to a point where you hopefully get your quad in the air quite quick.Normally you just need to choose your Airframe in the GUI and you are able to fly (at least with KISS ESC), otherwise you can download presets of well known pilots for given configurations. And of course you can tweak the PID yourself through the GUI.The software setup side is reduced as far as we could, many things are already taken into account for you, if you have some solid soldering skills you should be able to build your quad pretty quick. A known feature is also the telemetry, in combination with our 32bit ESC line it‘s possible to show the live telemetry data via OSD on your FPV live feed or in the KISS FC GUI. This way you get useful informations like the Voltage of your battery, current consumption, ESC temperature and motor RPM. Other FC firmwares (eg. Betaflight) are ported for the use with the KISS FC V2.ARM-Cortex M7 MCUwith FPU @ 216Mhzfor even the most complex algorithms. up to 12 times faster now.Powered directly by the battery(2-6S) max. 500mA @ 5Vavoids unnecessary weight.Onboard USBCP2102 USB-UARTUSB controller for easy updates of FC and ESC directly via GUI.Bidirectional communicationultrafast Dshot 2400, sinHybrid and full Kiss Telemetry support.Serial Monster5 for all use cases.SpecificationsMCU: STM32F722RET6 @ 216 MHzIMU: MPU6000Weight: 5gMounting: 3x3cm  (mit 3,3mm L?chern)Voltage: 2-6S (direkt)Tri, Y4 and Y6 * Quad + / x * Hexa + / xThe needed USB driver will be installed when you connect the flight controller the first time. It could take several minutes till you can bind the flight controller to the GUI.Supported FrSky Sbus, Graupner SumD, TBS CROSSFIRE and Multiplex SRXL as S-Port, HOTT, TBS CROSSFIRE and Sensorbus.Turtle mode supported5x SerialRunCam Split supportedRGB Led supportedDShot 2400FW via GUIAdvanced adaptive FilterAdvanced Motor LayoutWindows, OSX, Android supportedWiring Diagram of Kiss FC V2- Click to enlarge.Flyduino KISS FC V2 Connection Plan by Philipp Seidel.  Click to enlarge

    $79.99 $65.59, Save 18% OFF

    SKU:KSFCV2

    Weight: 0.10 kg

  • OMNIBUS AIO F7 V2 Flight Controller

    Features:- F7 MCU - faster than the current F3 and F4 processors- Two gyros on the flight controller: an MPU6000 for sampling up to 8khz and ICM20608 for sampling up to 32khz- Built in betaflight OSD- 36x36mm, mount holes 30.5x30.5mm- SD card reader for recording black box data (SD card not included)- Supports 2-4s natively, 5-6s with 220uf 35V capacitor- 5v/1A regulator- Port for easy connection to Airbot 4-in-1 esc (SH1.0 8P)

    $55.00 $47.85, Save 13% OFF

    SKU:OF7V2

    Weight: 0.10 kg

  • OMNIBUS F4 Pro Corner Flight Controller

    The Omnibus F4 Pro Corner flight controller uses the ICM20608 over SPI for the best possible flight performance. With onboard damping box, the ICM20608 runs perfect under 32k Gyro loop. If you havent already seen it, you should check out Joshs awesome video on different IMUs. Also onboard are a barometer and AB7456 OSD chip for the BetaFlight integrated OSD.Omnibus F4 Pro Corner supports 3-6s LIPO direct input, build in Current Sensor and Power Filter too.The on Board PDB is tweaked by using 12-Layer PCB design. There is only 0.2-0.5 mohm internal resistance from input to each output padsFeatures:- STM32 F405 MCU, Runs Betaflight firmware(supported from v3.2)- ICM20608 Over SPI Bus in damping box. (optional MPU6000)- 30.5x30.5mm Mounting holes- Supports Lipo direct plug in (3-6S)- Suports 5V 1A BEC output(Buck)- STM32 controls OSD chip over SPI in DMA mode(Betaflight OSD)- Build in Current sensor- Build in Professional level PDB- Build in LC filter for Camera power(max 800ma)

    $49.99 $43.99, Save 12% OFF

    SKU:CF4PC

    Weight: 0.10 kg

  • X-Racer F4 Flight Controller

    X-Racer is making a return with an all new update. Introducing the X-Racer F4. Like we mentioned before with the X-Racer F303, the same remains true for the X-Racer F4. This board is not for everyone and is designed with simplicity in mind. If your one of the guys that tries to stay away from the AIO flight controllers then chances are high this board is for you. X-Racer F4 offers a minimalistic approach to the flight controller market while still giving you the features you need for racing and freestyle flight. This board has strong roots to the X-Racer F303 and in many ways still offers the same functionality of the previous versions with only offering two major updates. We have upgraded to an F4 processor to ensure that the CPU loads will remain low with the newest heavy hitting release of Betaflight 3.2, and we have also upgraded to include the OSD chip and give you full access to Betaflight OSD which many have come to love and cant live without. X-Racer F4 also comes with 6 PWM outputs making it an excellent choice for those of you whom may be more interested in running a hex setup for Freedom Class racing.Download Firmware:  Click HERE.Friendly reminder: Due to only the UART1 has built-in inverter for SBUS receiver, other UART 3-6 are without built-in inverters, the receiver needs to connect the TX pad of flight controller directly without using its built-in inverter.Layout of X-Racer F4 (Click to enlarge the picture)Wiring Diagram of X-Racer F4 (Click to enlarge the picture)

    $33.32 $27.32, Save 18% OFF

    SKU:XRF4FC

    Weight: 0.10 kg

  • OMNIBUS F4 Nano v3 with LC filter

    - A new generation AIO Flight control for FPV, based on F405 MCU, using F4 MCU controls OSD over SPI bus in DMA mode, OSD Configation has been incl. in Betaflight GUI.- Supports SD Card and LIPO direct input (2-6S)- MPU6000 at SPI bus. No Flash for blackbox functionFeatures:STM32 F405 MCU, Runs Betaflight 3.2 firmwareSBUS/PPM input (Pinheaders)4PWM output (1-4Pinheaders and Sh1.0 Plug)Only 25x25mm, mount holes 20x20mmIncl. Barometer BMP280SPI Sensor MPU60002-6S Lipo Direct poweron board LC filterUpdate on August 14th: Add a connecting cable.

    $35.99 $29.51, Save 18% OFF

    SKU:OBF4V3

    Weight: 0.10 kg

  • RaceFlight Millivolt Flight Controller

    MillivoltThe RaceFlight Millivolt flight controller is the most advanced, performance driven, flight controller ever designed in a tiny package. Capable of running 32kHz gyro sample, PID loop, and motor loop, processing all calculations in real time. The Millivolt is truly at the top of its tiny class . The Millivolt uses a F405 MPU and an Invensense 20602 gyro in combination with RaceFlight software to give you the BEST performance possible. This gyro is by far the most noise free and accurate gyro available.PerformanceThe Millivolt presents not only the BEST performance, but also the most STABLE performance due to the amazing vibration rejection technology implemented in RaceFlight. Our filters allow your quad to stay in the air no matter what! Damaged propellers caused by that insane gate clip on turn 3? Not a problem. You can still finish the race! For most people tuning is not even required. Our boards come preloaded with software and defaults that should fly amazing for 99% of people.In addition to the vibration rejection technology, the SSG (Invensense 20602) gives you the highest speeds currently possible with the lowest noise floor and highest sensitivity. The Invensense 20602 gyro has never been used in any flight controller before (except the Revolt) and definitely gives you the leading advantage over others.SoftwareOur flight controller comes pre-loaded with the latest RaceFlight Community release. Just go to the google store and download the latest configurator and you should be ready to connect. Drivers should no longer be needed.RaceFlight One is also available in beta format. Just join our slack at https://raceflight.net/invite/ and ask to be added to the RaceFlight One channel. This is truly amazing software, which flies so well you can completely eliminate prop wash. Setup is a breeze as well, just run a couple wizards and you will get right up into the air.Setup SimplicitySetting up the Millivolt is easy. The solder pin layout is easy to read with motor connections in each corner. Just solder the closest motors and remember the order 1, 2, 3, 4. Select your voltage on the bottom, as well as inverted or not. The Millivolt also features DFU free updating and a self-healing and updating bootloader, just in case something does go wrong.FeaturesIntegrated vibration dampening dummiesInverter for Taranis and Futaba radios3.3v or 5.0v for Spektrum, Taranis, etcLED Driver for WS2812b programmable LEDInfrared LED Race Transponder support – just solder an infared LED to the Revolt and set it up in the RF1 configuratorFuture iPhone and Android configurator supportHigh Speed 32khz gyro, lowest noise floor and highest sensitivity gyro ever usedThrough hole solder pads – forms an I-Beam when soldered for extra strengthFrSky Taranis, Spektrum, Futaba, JR, IBus, Sbus and other radio supportIntegrated buzzer driverVoltage and current ADC pins, for full voltage and current monitoringFull telemetry output supportESC flashing and configuration built into configuratorMost active software developmentSelectable 3.3v or 5v voltage2 serial uartsBluetooth expandableF4 processor16mb of flash memoryGPS expandableDimensions: 25mm x 25mmMounting holes: 20mm squared to center of holes

    $41.88 $38.53, Save 8% OFF

    SKU:RFMFC

    Weight: 0.10 kg

  • RaceFlight F4 Flight Controller V2

    The latest RaceFlight Revolt flight controller, with integrated dampeners and upgrades so the flight controller will be compatible with future software upgrades.RevoltThe RaceFlight Revolt flight controller is the most advanced, performance driven, flight controller ever designed. Capable of running 32kHz gyro sample, PID loop, and motor loop, processing all calculations in real time. The Revolt is truly at the top of its class . The Revolt uses a F405 MPU and an Invensense 20602 gyro in combination with RaceFlight software to give you the BEST performance possible. This gyro is by far the most noise free and accurate gyro available.PerformanceThe Revolt presents not only the BEST performance, but also the most STABLE performance due to the amazing vibration rejection technology implemented in RaceFlight. Our filters allow your quad to stay in the air no matter what! Damaged propellers caused by that insane gate clip on turn 3? Not a problem. You can still finish the race! For most people tuning is not even required. Our boards come preloaded with software and defaults that should fly amazing for 99% of people.In addition to the vibration rejection technology, the SSG gives you the highest speeds currently possible with the lowest noise floor and highest sensitivity. The Invense 20602 gyro has never been used in any flight controller before and definitely gives you the leading advantage over others.FeaturesIntegrated vibration dampening dummiesDual inverters for Taranis and Futaba radiosTrue hardware radio diversitySelectable voltage for your UARTsLED Driver for WS2812b programmable LEDInfrared LED Race Transponder support – just solder an infared LED to the Revolt and set it up in the RF1 configurator – *** features coming soon within codeFuture iPhone and Android configurator support – *** features coming soon within codeHigh Speed 32khz gyro, lowest noise floor and highest sensitivity gyro ever usedThrough hole solder pads – forms an I-Beam when soldered for extra strengthFrSky Taranis, Spektrum, Futaba, JR, IBus, Sbus and other radio supportIntegrated buzzer driverVoltage and current ADC pins, for full voltage and current monitoringFull telemetry output support *** features coming soon within codeESC flashing and configuration built into configuratorMost active software developmentSelectable 3.3v or 5v voltage4 serial uartsBluetooth expandable *** features coming soon within codeF4 processor16mb of flash memoryGPS expandable *** features coming soon within codeDimensions: 36mm x 36mmMounting holes: 30.5mm squared to center of holes

    $38.88 $36.94, Save 5% OFF 1

    SKU:RF4FC

    Weight: 0.10 kg

  • KISS CompactCTRL CC All-in-One

    ***  FPV Model is an authorized dealer of FLYDUINO KISS. Genuine KISS products guaranteed.KISS CompactCTRL "CC" (AIOv2) - new Member of the KISS integrated FC&ESCs Family This version of the All-in-One board by Flyduino consists of a KISS 32bit flight controller and 4x 32bit KISS ESCs, rated at 16A (21A active limit), great for mini FPV setups.Its made for instant DIY success as you only need to solder motor wires, connect power and a radio and go. The KISS CC should be ideally driven up to 4s and up to 4 inch props. 5 inch props are possible but you need to choose motors carefully. The CC will actively limit the output to 21A.The CC comes preflashed with FC fw v1.1RC6 and ESC16A fw v110aMore Infos & Downloads: http://kiss.flyduino.net/kiss-compactctrl-cc-allinone-fcescs Specs of the CCWeight of PCB: 11g (without wires)Size 35x42mm (with cut off corners)4x KISS ESC 32bit ESCs 2-4S 16A (21A active current limiter)KISS FC F3 32bit with serial, buzzer and LED ports.Fully Dshot600 capableThe CC supports full telemetry and logging via serial port.Setup is the same as with the regular KISS FC.

    $97.99 $91.13, Save 7% OFF

    SKU:KCCIO

    Weight: 0.10 kg

  • Flycolor RAPTOR S-Tower 12A BLHeli-S 2-3S ESC with F3 Flight Controller Built-in OSD

    Specification:Brand name: FlycolorItem name: 12A BLHeli-S 2-3S ESC with F3 Flight ControllerFirmware: BLHeli-SContinuous Current: 12ABurst Current: 15AInput Voltage: 2 – 3SSize: 30.5*33.4*19mmBEC: 5V/1A (F.C)Weight: 11.5gFeature:- EFM8BB21F16G MCU with 50 MHz maximum operating frequency. using dedicated 3in1 drivers, makes the start more smooth. ESC maximum speed is limited to 500k eRPM.- Small size&lighter in weight. More suitable for ultra small multirotors.- Two layers tower structure between 4in1 ESC and FC using quick pin connection. makes the installation faster and more convenient- Exposed pads for Battery and Motor wires, fast welding without additional disassembly, motor replacement is more convenient .- F3 flight controller, supports PPM and SBUS remote control / receiving mode.- FC integrated OSD, no external OSD device is required, integrated 5V/1A for Image transmitter, camera, buzzer, LED and other peripheral devices ;- BLHeli-S firmware designed for superior performance in multirotors, and uses hardware generated motor pwm for smooth throttle response and silent operation.- There are tuneable parameters that can make the code run well even in the most demanding situations, although default settings will work excellently in normal operating environments.- The code supports regular 1-2ms pulse width input, as well as Oneshot125 , Oneshot42 and Multishot . The input signal is automatically detected by the ESC upon power up.- Supports Dshot digital signal, anti-interference ability is stronger, and do not need throttle calibration.

    $50.99

    SKU:FCRST

    Weight: 0.10 kg

  • DYS F4 Flight Controller

    Specifications:* OMNIBUSF4 firmware* Master STM32F405 GRT6, refresh rate up to 6K * PCB 3OZ copper enhance current stability and cooling fast* 5V 3A BEC output* Exposed pad for easy soldering* Compatible with all ESCs, as well as DYS 4-in-1 esc without soldering * Integrated OSD, no need to flash firmware additionally,debug OSD via BF ground station. * Integrated current meter to monitor the real-time power consumption * Adjust the PID by OSD via remote control* Adjust the VTX via open ports such as power, frequency band, frequency point (Note: The VTX should have this function like TBS one and the upcoming DYS VTX.)* DYS F4 flight control with 4 damping balls reduce the vibration to make it fly stably. * 2-6s lipo support* Net weight: 11.2g (exclude wire)* Size: L42 * W36mm, hole distance: 30.5*30.5mm* Gyro: MPU6000

    $37.86 $35.97, Save 5% OFF

    SKU:DYSF4

    Weight: 0.10 kg

  • BetaflightF3 Flight Controller

    BetaflightF3 Flight Controller | REVIEW AND HOW TO by Joshua BardwellBetaflightF3 is the flight controller designed to use every possible feature of Betaflight. More than the last half year has been spent in development. Boris B has worked with us to go over features and design aspects to help give us insight into what betaflight users want/need. This board features a 3A power draw giving users extra room for added attachments through uart ports. The six layer PCB is a more expensive design approach but was needed to give the ability to have a PDB that was capable of having wiring pads on both the top and bottom of the board. By using the six layer design we were able to increase the size of the pads and work around all the components all the while giving esc connections in the corners of the board rather than bunching all connections on either the top OR the bottom. Featuring a fully functioning OSD that can be configured in Betaflight this board will make configuring your OSD a breeze. The team at betaflight have been hard at work developing DSHOT and this board is also compatible with the latest release. But we didn’t stop there, this board also features a micro adapter to accept TF cards for those of you that like to follow up your flights with reviewing black box logging...we think we know of at least one guy that will like that. FeaturesIntegrated PDBBuilt in OSD customizable via Betaflight OSDCurrent sensorIntuitive layoutSD card slot for BlackBoxTailored to support BetaflightWhen running 8K/8K, CPU usage remains lowSpecificationsF3 ProcessorMPU6000 Gyro/ACC SensorBEC Max current 5V 2ABuilt in OSD – configurable via Betaflight GUISD Card adapter for BlackBoxCurrent sensorPower distribution board with six-layer PCBOSD Max Current: 145AWeights 8.6g***Note: Please do not connect to any equipment with the loading over 1.5A.Friendly Reminder: Choosing your power supply for video is relatively simple. Betaflight FC has two options, 5v and battery voltage. Choose your camera voltage by jumping RAM with either the 5V solder section or the Vbat solder section. (its recommended to use Vbat, Most cameras and Video transmitters can run off battery voltage) If using 5v it is recommeded to only power your camera and get the power for Vtx from another source. 

    $42.99 $29.66, Save 31% OFF 3

    SKU:BFF3

    Weight: 0.10 kg

  • KISS FC 32bit Flight Controller V1.03

    *** FPV Model is an authourized dealer of FLYDUINO KISS. Genuine KISS flight controller guaranteed.Before Purchasing: Please keep the packaging after receiving KISS flight controller. Each genuine KISS FC has a unique serial number on the packaging, while fake KISS FC does not and can not be activated. Flyduino, the designer and manufacturer of Kiss FC, will offer the technical support only to the ones with serial numbers. If the packaging is lost, you may fail to get the technical support from Flyduino in time. Besides, for any return of KISS products, you will need to send back the KISS packaging as well.- Changed bootloader solderpads to a press button- Changed USB Port typeAs we felt the need for a modern more simplified 32bit Flightcontroller, we made the KISS FC, which includes a complete own Flight Controll Firmware development who get rid of some old ballast, this took some time, but the result is very pleasing.The Idea was to simplify some things and due to intensive long term testings of some pretty good Pilots we where able to optimize the code to a point where you hopefully get your quad in the air quite quick.Normally you just need to choose your Airframe in the GUI and are able to fly (at least with KISS ESC), otherwise you can download presets of well knowen Pilots for given configurations and of course can tweak the PID yourself over the GUI.The software setup side is reduced as far we can, many things are allready taken in to account for you, if you bring some solid soldering skills you should be able to build your quad pretty quick.A new feature is also the inbuild telemetry, in combination with our 32bit ESC line its possible to show the live telemetry data via OSD on your FPV live feed or in the KISS FC GUI.?This way you get usefull informations like the Voltage of your battery, current consumption, ESC temperature and motor RPM.Supported copter types:- Tri- Quad +/x- Hexa +/xSupported RX types:- PPM Sum- Spektrum Sat. (serial / DSM2 & DSMX)- Futaba / Taranis SBUS- Jeti ExBus- Graupner SumD / SumO- MultiPlex- classic RX with single channel output- STM32F303CCT6- MPU6050Weight: 4.6gMounting Holes: 3x3cm pattern, with 3.2mm holes (widely compatible)Voltage: 2-6SDriver for STM32F303CCT6Normally you dont need to download any driver for the USB support.Windows 7 8 and 10 care for this on their own after you connected the device.The connection diagramm / Pinout you find in KISS-FC GUI.DOWNLOADS (Manuals, Firmware, GUIs): Click HereReview on KISS FC by Oscar Liang

    $39.99

    SKU:KSFC

    Weight: 0.10 kg

Find us on Google+ Watch us on Youtube Like us on Twitter Follow us on Facebook

Home   |   About Us   |   New Products   |   Multi-Rotors   |   FPV Airplanes   |   FPV Equipment   |   Battery / Chargers   |   Tools & Accessories   |   Contact Us   |   Blog   |  Site Map

Product Tags: ABCDEFGHIJKLMNOPQRSTUVWXYZ0-9

Copyright © 2015 FPVMODEL.COM®. All Rights Reserved.