Sorted:
  • BetaflightF4 Flight Controller

    BetaflightF4 How to ESC Telemetry, Smart Port Audio, Smart Port TelemetryFriendly Reminder: Upon receiving your FC, please connect to USB and calibrate before continuing to build and solder to it.  BetaflightF4 is the follow up design to the very popular BetaflightF3. Following in the same path as Betaflight F3 we have kept a very similar footprint in terms of design with a few added modifications. The F405 has replaced the F303 to allow for lower CPU loads.We have eliminated the 5v/3.3v jumper and added two seperate connection points, one for sbus and one for spektrum users. The jumper still remains for the battery voltage/5v connection for connecting your camera. While wiring the board it is recommended to get power for your vtx either from a different 5v source on the board or if using a higher voltage vtx power it from the battery input coming into the pdb. Running ground loop at Agnd with gnd wires from camera and vtx is still recommended to give the cleanest video signal. Another small design change to this board was changing the BEC, this change takes the recommended 5v 2A current limit and drops it down to 5V 1.5A, its a small change but one that we opted for in order to use a more reliable BEC.BetaflightF4 now comes with telemtry pads for BLHeli32 ESCs these pads are located between the signal and gnd pads for the ESC connections.FeaturesIntegrated PDBBuilt in OSD customizable via Betaflight OSDCurrent sensorIntuitive layoutFlash memory for blackboxTailored to support BetaflightWhen running 8K/8K, CPU usage remains low Download Latest Firmware: Betaflight 3.2.0SpecificationsF405 ProcessorMPU6000 Gyro/ACC SensorBEC Max current 5V 1.5ABuilt in OSD – configurable via Betaflight GUICurrent sensorPower distribution board with six-layer PCBOSD Max Current: 145AWiring Diagram - Click to enlarge!BetaflightF4 Connection Plan by Phillip Seidel

    $44.73 $33.99, Save 24% OFF 3

    SKU:BFF4

    Weight: 0.10 kg

  • *Pre-order* Betaflight Hive Backpack

    * Update on December 3rd: We expect the Betaflight Backpacks to be in this week. However, the betaflight custom packaging (See the picture above) will not be ready until the middle of the month. We have had several requests about the pre-order shipping time over the previous few days and understand some of you are wanting them sooner rather than later. So the decision is yours...Would you like us to ship ASAP or would you like to wait for the custom packaging? Let us know your thoughts. Thanks again for your patience.* We are now taking pre-orders on Betaflight "Hive" Backpacks to judge the demand.  During this time we are selling the backpack at a discounted rate of $169.99 USD, while the estimated final selling price is around $199.99 USD. * Before Purchasing: Due to the size limit, we offer free shipping on the backpack by EMS only.This is the Betaflight Hive Backpack. The design of this bag has taken many months and even after we released it for pre-orders, customer suggestions kept making us go back to the "final" prototype and add some of their suggestions. In reality, this is not just a backpack that was designed by us but its more of a backpack that has been designed and then re-design by users like you. We do our best to listen to your feed back and that is proven in the design of this backpack. Requests for hard shell covers, reverse the orientation of the side pockets, make the hand held carry bgk into a liposafe fire resistant bag are just a few of the suggestion that we went back and updated during the design process. After reviewing the final, final prototype we here at FPVMODEL feel like the user sugguestions weve received from our clients and friends on facebook, have helped make certain that this bag has the best quality and features available. More pictures of the final prototype will be updated soon. We think youre gonna like them. The overall design of this backpack is geared towards those that are serious fliers and have multiple quads and many tools and accessories that they carry with them while traveling by air or even just to the local field. Betaflight Hive Backpacks are performance tested, at fully loaded capacity, using our strict control standards. Before we offer this product for sale, it is put through test to ensure it’s strength, durability, and dependability that is represented by the most demanding frequent travelling quad pilots. This attention to quality results in us (FPVMODEL) and (Betaflight) being able to offer the best warranty in the industry. Click here for the backpack warranty or download the PDF.Features:International carry-on size compatibility for air travel. Dedicated lap-top pocketDedicated lipo bagElastic daisy chain tool panel for your hex drivers and other hand held tools. Large interior pocket for carrying props with hard shell cover on the bag for added protection from outside forces. 1680D ballistic nylon bag material for long life durability. Featuring the best zippers in the market made by YKK to ensure long lasting zipper life. Contoured adjustable padded harness with height adjustable chest strap. Rain cover that pulls out from bottom panel pocket for fast rain protection.Exterior Dimensions:  56 x 34 x 18cm*Description and photos are in the early stages. These will be updated as progress moves forward with the manufaturing process.  Large interior pocket for carrying props with hard shell cover on the bag for added protection from outside forces.Interior and Exterior FPV Quad mounting locations.While we were designing the Betaflight backpack one thing kept coming up in the design aspect was how much room the transmitter took up inside the bag. So, we thought the best design would be to make a hard shell top mounted case on the top of the bag. The hard shell top of the case allows for extra protection of your transmitter and frees up valuable space inside the bag. The interior of the bag is very similar to other DSLR style camera bags and allows for multiple design layouts by using cushioned dividers that velcro in place and let each user layout their own custom setup based on their specific needs. Featuring the best zippers in the market made by YKK to ensure long lasting zipper life. Dedicated lipo bag to store your Lipos, no need to worry about the safety of batteries now. Still Plenty room to store your FPV accessories, you are able to carry up to 30 1500mAh batteries!!!Dedicated laptop pocketWe pay attention to every detail of the backpack. The inside fabrics come with Betaflight Logo. Comes with a GoPro mount, recording every wonderful moment has never been so easy.  (GoPro camera not included)**** Friendly reminder: Price for Betaflight HIVE backpack only. Above pictures for demonstration purpose that the quads, tools, GoPro and other accessories are not included.

    $199.99 $169.99, Save 15% OFF    4

    SKU:BFBP

    Weight: 3.50 kg

  • *Pre-order* Skyzone SKY03 3D FPV Goggles

    Skyzone SKY03 FPV GogglesExpected shipping date: December 20th, 2017Skyzone is a professional manufacturer of FPV goggles, now here comes the third generation 3D FPV goggles named SKY03. The SKY03 is an upgraded version of the famous SKY02S 3D FPV goggles. They boast a great feature set, comfortable to wear and fit a wide range of eyesight conditions as well. They look very nice in the renders on the video shown above and we are excited to see what these will look like in person and more importantly, how they will feel and perform. As a business partner of Skyzone, FPV Model will be the first on the market to receive the SKY03 FPV goggles. Heres a list of features and specs:With Head Tracking functionDiversity Receiver Module with Dual Antennas ISM 5.8GHz 48-channerl diversity receiverSupport HDMI, DVR, AV IN/OUTBuilt with Front Camera Up to 43 Degree FOVBinocular Display,SVGA 800X600 resolution,binocular display.Multiple LED Light effect mode support.Intimate Design of Human MechanicsThe two 5.8GHz wireless receiver modules, the two independently workable display modules and the new DVR system used to support the 2D & 3D display modes are built in the SKY03 FPV goggles. The wireless receiver system can work in the diversity receiver mode to improve the receiving effect. In this mode, the channel and band settings for wireless receiver can be compatible with most of the conventional ISM 5.8GHz transmitters, in order to support the 6 bands and the 48 channels (for detailed bands and channels, see the specification).The matching 3D camera SCAM303 and the conventional 5.8G transmitter can be put into use in the 3D mode. The two lenses of the 3D camera can be set for shot by means of the parallel method. When the camera is set for a certain close shot, the third dimension will be enhanced effectively. When the camera is set for a long-distance shot, the third dimension will be weakened, but the more vivid visual experiences will be presented as a whole.The new DVR system can not only further enhance the quality of analog video recording, but also can make use of the high-quality H.246 video compression technology to better restore the video screen, save the more storage space, support the 128GB high-capacity memory card(UHS-I U1), and support the automatic video recording function. For details, see the description of the "Video" section.

    $459.00

    SKU:SKY03

    Weight: 0.90 kg

  • RunCam Nano FPV Camera PAL

    Description:Model: RunCam NanoImage Sensor: 1/3" CMOS SensorHorizontal Resolution: 650TVLLens 2.1mm : (M8) FOV160°Signal System: NTSC/PALS/N Ratio: 50dB (AGC OFF)Electronic Shutter Speed : AutoAuto Gain Control: AutoMin. Illumination: 0.1Lux@1.2FWDR: AutoDNR: AutoDay/Night: AutoPower: DC 3.3-5.5VWorking Current: 140mA@3.3V / 140mA@5.5VDimensions: L14mm*W14mm*H17mmNet Weight: 2.5g

    $19.99

    SKU:RCNC-P

    Weight: 0.10 kg

  • RunCam TX200 3.5-5.5V 5.8G 48CH Video Transmitter

    TX200 VTX is the first video transmitter from Runcam. It is super light weight and designed specifically for the Runcam Micro Swift 2 camera.The Runcam TX200 is a very simple and plain VTX, there is only one button to change channel, band and power, and some LED’s indicating what settings the VTX is on. The VTX is built on a 19x19mm square PCB and it can be mounted directly on the back of a Micro Swift or Micro swift 2 with the provided standoffs and screws.You can use this VTX as a standalone VTX too if you wish. The standoffs leave a gap between the camera and VTX PCB’s, allows for airflow and better cooling.To know more about Runcam TX200 video transmitter, you can take a reference to Oscar Liangs review.Frequency SetupLock mode:Red LED flashes, only 25mW & limited frequency available;Unlocked mode:Red LED keeps on, 200mW & all 48 channels available; By long pressing button for 10 seconds, you can switch between the two modes.Note: Before you get TX200 unlocked, it is highly recommended to know about the rules and regulations in your country about the frequency to avoid a fine or confiscation of your device.1 Blue LED for ChannelShort press the button to switch the Channel, Channel 1/2/3/4/5/6/7/8 in sequence. For each short press, the Blue LED flashes once, and only when its under the Channel 1, the LED is always on.6 Red LED for BandLong press the button two seconds to switch the Band, Band 1/2/3/4/5/6 in sequence.For each long press, the six Red LEDs light in turn.1 Orange LED for PowerLong press the button five seconds to switch the power, on is 200mw, off is 25mw, lock mode is limited to 25mw.Frequency TableParameter

    $14.99

    SKU:RCTX200

    Weight: 0.14 kg

  • Emax F3 Magnum Mini Tower System Bullet 12A 4 in 1 ESC And F3 Flight Controller

    EMAX “F3 MAGNUM MINI” FPV TOWER SYSTEM Designed for high performance Micro FPV racers, the F3 Magnum Mini packs in a F3 processor, Betaflight OSD and 12A 4 in 1 ESC that can handle up to 4s batteries. MPU6000 gyro is a proven performer for stable flight and resistance to vibration noise.The FC and ESC with neatly stack together with pinned interconnects that make your build easy to assemble and cleaner looking. This tightly pre-assembled package will fit any frame that has 20 x 20mm mounting hole spacing. The F3 Magnum Mini is the fastest way go from starting a new micro build to FPV Flight!4 in 1 Main Board - F3 FC + Betaflight OSD + 5v Regulator + Buzzer  The heart of the flight control systems is a powerful STM32F303 MCU and MPU6000 gyro flashed with Betaflight for proven rocksteady flight stability. The integrated 5v/3A voltage regulator means clean power for all the FC/OSD components and other attached boards such as VTX, RX and FPV Camera. Betaflight OSD with easily customizable layout of vital flight information and ability to change FC flight parameters. On board buzzer for battery level warning or lost model finder functions.

    $45.99

    SKU:EMF3MT

    Weight: 0.15 kg

  • *Pre-order* KISS FC V2 - 32bit Flight Controller

    *** FPV Model is an authourized dealer of FLYDUINO KISS. Genuine KISS flight controller guaranteed.Expected shipping date: Available in stock, but waiting for the shipping notification from KISS Flyduino.Before Purchasing: Please keep the packaging after receiving KISS flight controller. Each genuine KISS FC has a unique serial number on the packaging, while fake KISS FC does not and can not be activated. Flyduino, the designer and manufacturer of Kiss FC, will offer the technical support only to the ones with serial numbers. If the packaging is lost, you may fail to get the technical support from Flyduino in time. Besides, for any return of KISS products, you will need to send back the KISS packaging as well.Finally Flyduino release the KISS V2 flight controller with a F7 processor. As an authourized dealer of Flyduino, FPV Model is one of the first to receive the FCs. A new simplified Flight controller, the KISS FC V2 includes a complete own Flight Control Firmware development. The Idea was to get the simple KISS FC to the next level and due to intensive long term tests of some pretty good Pilots we were able to optimize the code to a point where you hopefully get your quad in the air quite quick.Normally you just need to choose your Airframe in the GUI and you are able to fly (at least with KISS ESC), otherwise you can download presets of well known pilots for given configurations. And of course you can tweak the PID yourself through the GUI.The software setup side is reduced as far as we could, many things are already taken into account for you, if you have some solid soldering skills you should be able to build your quad pretty quick. A known feature is also the telemetry, in combination with our 32bit ESC line it‘s possible to show the live telemetry data via OSD on your FPV live feed or in the KISS FC GUI. This way you get useful informations like the Voltage of your battery, current consumption, ESC temperature and motor RPM. Other FC firmwares (eg. Betaflight) are ported for the use with the KISS FC V2.ARM-Cortex M7 MCUwith FPU @ 216Mhzfor even the most complex algorithms. up to 12 times faster now.Powered directly by the battery(2-6S) max. 500mA @ 5Vavoids unnecessary weight.Onboard USBCP2102 USB-UARTUSB controller for easy updates of FC and ESC directly via GUI.Bidirectional communicationultrafast Dshot 2400, sinHybrid and full Kiss Telemetry support.Serial Monster5 for all use cases.SpecificationsMCU: STM32F722RET6 @ 216 MHzIMU: MPU6000Weight: 5gMounting: 3x3cm  (mit 3,3mm L?chern)Voltage: 2-6S (direkt)Tri, Y4 and Y6 * Quad + / x * Hexa + / xThe needed USB driver will be installed when you connect the flight controller the first time. It could take several minutes till you can bind the flight controller to the GUI.Supported FrSky Sbus, Graupner SumD, TBS CROSSFIRE and Multiplex SRXL as S-Port, HOTT, TBS CROSSFIRE and Sensorbus.Turtle mode supported5x SerialRunCam Split supportedRGB Led supportedDShot 2400FW via GUIAdvanced adaptive FilterAdvanced Motor LayoutWindows, OSX, Android supportedWiring Diagram of Kiss FC V2- Click to enlarge.Flyduino KISS FC V2 Connection Plan by Philipp Seidel.  Click to enlarge

    $79.99

    SKU:KSFCV2

    Weight: 0.10 kg

  • Wraith32 MINI V2 32bit BLHELI_32 35A ESC

    The Wraith32 Mini V2 35A ESC is an upgraded version of previous Wraith32 Mini 25A. Comparing to the first version, the Wraith32 Mini V2 has more capacitors to help smooth noisy environment, and the data transmission interface is placed outside.Specifications:2-6s LIPO input35A designed10*20mmBLHeli_32 is the third generation BLHeli code, following base BLHeli and BLHeli_S.BLHeli_32 runs on an ARM 32bit MCU, initially it will be on a Cortex-M0 running at 48MHz, but there are MCUs out there that can run a lot faster.So what can the increased MCU speed do?First of all, it can run input signals with lower latency at faster rates. Dshot up to at least Dshot1200, and at rates up to at least 32kHz is now supported.Secondly it allows packing of more functionality. - Like programmable pwm frequency, up to 48kHz, that can run motors even smoother, and also allows for moving of small but potentially disturbing humps in the throttle response. All ESCs have these bumps, with BLHeli_32 they can now be moved in the rpm range, to a place where the system has low sensitivity to them.- Like auto timing. Which is not the option to choose if you’re after max power. But if you want the most efficient running with very good robustness against desync, it is the perfect choice.- Like voltage and current limiting. Which is implemented in the code, and will be supported on some ESCs. Voltage limiting is desirable for fixed wing crafts. And current limiting adds protection against ESC failure.- Like programmable brake on stop force. Which allows control of the braking of fixed wing props.- Like improved direction change in bidirectional mode.- Like more to come in the future. Such as setup from the FC by using Dshot commands. Such as telemetry functionality. There is room to grow performance and functionality.Some Tips:BLHeli_32 ESC Firmware OverviewWhat is Dshot1200 and Why Dshot1200 is Better?How to Get Dshot1200 Running in Betaflight?Downloads:Download the latest BLHeli_32 Configurator here.Download the BLHeli_32 User Manual here.Download Pre-release version of Betaflight 3.2.0 here.

    $16.99

    SKU:W32MV2

    Weight: 0.10 kg

  • Wraith32 V2 35A 32bit BLHeli_32 ESC DSHOT1200

    The Wraith32 V2 is an upgraded version of previous Wraith32 35A that comes with 1800uf caps on board. Comparing to the first version, the Wraith32 V2 has more capacitors to help smooth noisy environment, and the data tranmisstion interface is placed outside.Wraith32 is the first 32bit BLHELI ESC that use the latest BLheli_32 firmware in the world. Dshot up to at least Dshot1200, and at rates up to at least 32kHz is now supported. If you are seeking for a small, powerful blheli_32 capable 32bit ESCs, the Wraith32 ESCs will certainly fit the bill providing 35Amps of power.The Wraith32 ESC runs in conjunction with an ARM 32bit compatible MCU. It can run input signals with lower latency, at faster rates, smooths out the RPM band, is capable of both voltage and current monitoring and limiting, as well as offering customization of the brake on stop force. Unlike current ESCs, the Wraith32 ESC has A LOT of room to grow and wide compatibility range with future products. One of the nicest features with the Wraith32 35A ESC is the auto timing feature, which (essentially) is designed to offer the pilot the smoothest and most efficient flight experience available, which is a freestyle pilots dream come true! Features:32bit Compatible ESC (Blheli_32)Dshot1200 up to 32kHzIncredibly small sizeVery low weightAuto Timing FeatureOn-Board RGB LEDBuild in Current sensorSmooth ResponseCompatible to BetaflightF4 Flight ControllerSpecifications:2-6s Lipo input35A designedCompatible to BetaflightF3 Flight ControllerSize: 15*30mmPackaging: One ESC each PP bag with Wraith32 lable.BLHeli_32 is the 3rd generation of BLHeli firmware after BLHeli and BLHeli_S. BLHeli_32 runs on an ARM 32bit MCU, initially it will be on a Cortex-M0 running at 48MHz, but there are MCUs out there that can run a lot faster.Now the first ESC that supports BLHeli_32 has already been announced – the Wraith32 and Wraith32 Plus. Luckily, FPV Model received these from the manufacturer Airbot as soon as they made them out, and all our customers have the chance to be the first in the world receive these new BLHeli_32 ESCs.Wraith32 Plus is a 6S powerhouse that supports voltage limiting and current limiting as well as a bright RGB LED.Wraith32 is a smaller 6S version that also supports voltage limiting and current limiting as well as a bright RGB LED.So what can the increased MCU speed do?First of all, it can run input signals with lower latency at faster rates. Dshot up to at least Dshot1200, and at rates up to at least 32kHz is now supported.Secondly it allows packing of more functionality. - Like programmable pwm frequency, up to 48kHz, that can run motors even smoother, and also allows for moving of small but potentially disturbing humps in the throttle response. All ESCs have these bumps, with BLHeli_32 they can now be moved in the rpm range, to a place where the system has low sensitivity to them.- Like auto timing. Which is not the option to choose if you’re after max power. But if you want the most efficient running with very good robustness against desync, it is the perfect choice.- Like voltage and current limiting. Which is implemented in the code, and will be supported on some ESCs. Voltage limiting is desirable for fixed wing crafts. And current limiting adds protection against ESC failure.- Like programmable brake on stop force. Which allows control of the braking of fixed wing props.- Like improved direction change in bidirectional mode.- Like more to come in the future. Such as setup from the FC by using Dshot commands. Such as telemetry functionality. There is room to grow performance and functionality.Some Tips:BLHeli_32 ESC Firmware OverviewWhat is Dshot1200 and Why Dshot1200 is Better?How to Get Dshot1200 Running in Betaflight?Downloads:Download the latest BLHeli_32 Configurator here.Download the BLHeli_32 User Manual here.Download Betaflight 3.2.0 here.

    $16.99

    SKU:W32V2E

    Weight: 0.10 kg

  • Wraith32 Metal 32bit BLHELI ESC

    The Wraith32 metal is a new 32bit BLHeli ESC that comes with superior quality. Comparing to the standard Wraith32, the Wraith32 metal has following features: The metal MOS has a better heat dissipation and gives more power. More capacitors. Better power supply lines Better stability. Better transmittion interface layoutBLHeli_32 is the third generation BLHeli code, following base BLHeli and BLHeli_S.BLHeli_32 runs on an ARM 32bit MCU, initially it will be on a Cortex-M0 running at 48MHz, but there are MCUs out there that can run a lot faster.So what can the increased MCU speed do?First of all, it can run input signals with lower latency at faster rates. Dshot up to at least Dshot1200, and at rates up to at least 32kHz is now supported.Secondly it allows packing of more functionality. - Like programmable pwm frequency, up to 48kHz, that can run motors even smoother, and also allows for moving of small but potentially disturbing humps in the throttle response. All ESCs have these bumps, with BLHeli_32 they can now be moved in the rpm range, to a place where the system has low sensitivity to them.- Like auto timing. Which is not the option to choose if you’re after max power. But if you want the most efficient running with very good robustness against desync, it is the perfect choice.- Like voltage and current limiting. Which is implemented in the code, and will be supported on some ESCs. Voltage limiting is desirable for fixed wing crafts. And current limiting adds protection against ESC failure.- Like programmable brake on stop force. Which allows control of the braking of fixed wing props.- Like improved direction change in bidirectional mode.- Like more to come in the future. Such as setup from the FC by using Dshot commands. Such as telemetry functionality. There is room to grow performance and functionality.Features:Build in Current sensorOn-Board RGB LED2-6s LIPO input35A designed15*30mmSome Tips:BLHeli_32 ESC Firmware OverviewWhat is Dshot1200 and Why Dshot1200 is Better?How to Get Dshot1200 Running in Betaflight?Downloads:Download the latest BLHeli_32 Configurator here.Download the BLHeli_32 User Manual here.Download Betaflight 3.2.0.

    $34.99

    SKU:W32MC

    Weight: 0.10 kg

  • Jie-star Skyhunter X8 FPV Foldable RC Drone

    Foldable design? Aerial photography? One key return and one key landing? Headless mode? WIFI and transmitter control? Yes, yes, yes !!! The new Jie-star Skyhunter X8  V2quadcopter has all the functions you are looking for? Easy to control, easy to carry. Flying a drone has never been so easy.JIE-STAR SKYHUNTER X8 RC quadcopter V2 is an incredible UAV whose arms and landing skids can be folded manually, making it barely bigger than your palm. It is ready to fly out of the box. Therefore, you can put the drone into nearly any bag for an outdoor activity. SKYHUNTER is a multicopter intended for beginners since One Key Takeoff, One Key Landing, One Key Return are easily accessible so that you can control the drone with ease.JIE-STAR SKYHUNTER X8 is no doubt one of the most popular portable drone on the market. FPV Model is a business partner of Jie-star, while others sell the X8 for over 60, here we are giving you a special price of $39.99. Check the link below, to see what others say at Youtube.Features:Wifi transmission system provides easy and fun FPV flight0.3MP camera can take photos and record videosBarometer set height function for precisely hold the heightFoldable design, portable and easy to carryH/L speed mode, 3D eversion, headless mode, one-key taking off/landing, one-key return function for cool flying3.7V 650mAh Li-po battery for about 5-7mins working timeUpgraded 2.4G 4CH transmitter for your easy controlThe latest 6-axis flight control system, provides super stable flightUnique fuselage design and high quality painting, outstanding appearanceSpecifications:Model name: X8TWColor: Black / WhiteRemote control: 2.4GHz / 4 ChannelsController Mode: Mode 2Main Material: ABSMotor type: brushed motorCamera pixel: 0.3MPFPV transmission: wifi real-timeFunction: forward/backward, up/down, left/right, sideward flight, hovering, 3D flips, H/L speed, headless mode, one-key taking off/landing, one-key returnRemote distance: about 80-100mCharging time: about 90minsFlying time: about 5-7 minutesQuadcopter battery: 3.7V 650mAh Li-po battery (35 * 30 *10mm)Transmitter battery: 2 * AA (not included)Item dimension:Unfolded: 290 * 290 * 90mm / 11.4 * 11.4 * 3.5inFolded: 120 * 95 * 55mm / 4.7 * 3.7 * 2.2inItem weight: 135gPackage list:1 * JIE-STAR X8TW RC Quadcopter1 * Transmitter (Mode 2)1 * 3.7V 650mAh Li-po Battery2 * Pair Spare Propellers1 * USB Charger1 * Phone Retaining Clip1 * Screwdriver1 * English ManualNOTE: Smartphone NOT included.New upgraded version w/ carry bagRegular Version:

    $39.99-$43.99

    SKU:JSX8D

    Weight: 0.80 kg

  • ZMR180 FPV Starter BNF Package

    ZMR 180 Carbon FPV Mini Quad - Full Review By BMSWebThe ZMR180 is a micro quad designed with "fun" in mind. Agile, quick, and small all fit together with this kit and its a blast to fly. Keeping simplicty in mind this frame has high quality 3mm bottom plate and a 1.5 mm top plate. Parts Included:1 x ZMR180 Frame4 x Dragonfly MC1806 2300KV Mini Motor 1 x X-Racer F4 Flight Controller4 x DYS XS 20A 3-4S ESC1 x RunCam Swift Mini 600TVL FPV Camera (Update on November 29th.)1 x Dragonfly 5.8G 48CH Vtx10 Pairs x DYS 4040 3-Leaf Propeller1 x MATEK PDB XT60 with BEC 5V/12V1 x Dragonfly Booster 5.8G 3dBi TX/RX FPV Antenna RP-SMA1 x XT60 power plug connector MaleNote: The frame have color Black and Red. We send by random. If you have the specified color, please leave a message at the check out page, thank you! Note: The battery that shown in the pictures is not included in the ARF combos.

    $199.99 $143.99, Save 28% OFF

    SKU:ZMR180PTM1

    Weight: 1.20 kg




Find us on Google+ Watch us on Youtube Like us on Twitter Follow us on Facebook

Home   |   About Us   |   New Products   |   Multi-Rotors   |   FPV Airplanes   |   FPV Equipment   |   Battery / Chargers   |   Tools & Accessories   |   Contact Us   |   Blog   |  Site Map

Product Tags: ABCDEFGHIJKLMNOPQRSTUVWXYZ0-9

Copyright © 2015 FPVMODEL.COM®. All Rights Reserved.