Sorted:
  • OMNIBUS AIO F7 V2 Flight Controller

    Features:- F7 MCU - faster than the current F3 and F4 processors- Two gyros on the flight controller: an MPU6000 for sampling up to 8khz and ICM20608 for sampling up to 32khz- Built in betaflight OSD- 36x36mm, mount holes 30.5x30.5mm- SD card reader for recording black box data (SD card not included)- Supports 2-4s natively, 5-6s with 220uf 35V capacitor- 5v/1A regulator- Port for easy connection to Airbot 4-in-1 esc (SH1.0 8P)

    $55.00 $45.65, Save 17% OFF

    SKU:OF7V2

    Weight: 0.10 kg

  • OMNIBUS F4 Pro Corner Flight Controller

    The Omnibus F4 Pro Corner flight controller uses the ICM20608 over SPI for the best possible flight performance. With onboard damping box, the ICM20608 runs perfect under 32k Gyro loop. If you havent already seen it, you should check out Joshs awesome video on different IMUs. Also onboard are a barometer and AB7456 OSD chip for the BetaFlight integrated OSD.Omnibus F4 Pro Corner supports 3-6s LIPO direct input, build in Current Sensor and Power Filter too.The on Board PDB is tweaked by using 12-Layer PCB design. There is only 0.2-0.5 mohm internal resistance from input to each output padsFeatures:- STM32 F405 MCU, Runs Betaflight firmware(supported from v3.2)- ICM20608 Over SPI Bus in damping box. (optional MPU6000)- 30.5x30.5mm Mounting holes- Supports Lipo direct plug in (3-6S)- Suports 5V 1A BEC output(Buck)- STM32 controls OSD chip over SPI in DMA mode(Betaflight OSD)- Build in Current sensor- Build in Professional level PDB- Build in LC filter for Camera power(max 800ma)

    $49.99 $38.99, Save 22% OFF

    SKU:CF4PC

    Weight: 0.10 kg

  • DYS ARIA 35A 3-6S Blheli_32 Dshot1200 ESC

    It is always better late than never. Finally the DYS Aria 35A BLHeli_32 ESC is officially launched. If you are still running its XM30A, this could be a very good upgrade for the BLHeli_32 goodness.DYS ARIA 35A 3-6S Blheli32 Dshot1200 ESCSpecifications:Current Rating: 35A (40A burst)Voltage Rating: 3S to 6SDimension: 32mm x 16mm x 5mmWeight: 4.73g bare PCB, 8.1g with wiresCurrent sensing and limitingBuilt-in Programmable RGB LEDPrice: $15.99 eachSupports DShot1200 and older ESC protocolsFeatures:With 32bit ARM Cortex MCU STM32F051 48MHZ micro processor, throttle 2048 resolution ratio, strong anti-interference capacity.Built-in sensor can be reaction of temperature, output power, output current etc, also programmable for protection.Support Blheli_32 firmware, can use the signal wire to upgrade the firmware or change the configuration on line.Current Meter to help show current indication of OSDWith USB linker can be programmable throttle setting like support positive and negative, two way mode, FPV 3D mode, motor speed, braking, PWM frequency, inlet angle speed setting, onboard RGB LED for customize color, Beep etc.It use the self-adaption control system,can go automatic with the all kind of the motor in the market,at the mean time it support up to 500HZ PWM, oneshot 125, oneshot 42, Multishot and Dshot 150/300/600/1200.With special optimize in multi-axis, the motor can launch smoother in a good throttle curve, fast response,great power, and highly support the multi-axis,fixed-wing and helicopter.The twisted-pair signal wire can lower the crosstalk inside cooper wire when it transfer,which will make the flight more stable.MCU hardware,Driver circuit, Mosfet will come with double voltage protection.To adopt the new process MOSFET of low internal resistance, will help increase resistance to flow. Also, the professional MOS driver chip makes the best efficiency.Mosfet is covered with aluminum sheet for cooling,which can bring more efficiency and stability.With special process of 6 layer thicken PCB will lower resistance, small calorific value and bigger impact resistance current.Nice optimize layout of the components and parts makes a smaller size, lighter weight and easy to build.

    $15.99 $14.07, Save 12% OFF

    SKU:DA35A

    Weight: 0.10 kg

  • Brotherhobby Dead Pool Returner R5 2306 2450kv Brushless Motor

    The Brotherhobby Returner R5 2306 2450kv Brushless Motor has been optimized for fpv racing. One of the ways they have done this is by using a new EZO 8x4x3mm bearing with a higher RPM and less weight. They have also added a 5mm hollow motor shaft and the naked base thickness is increased to be 3mm to increase durability.Specifications:KV:2450KV/2650KVConfiguration: 12N14PNo.of Cells(Lipo): 4-5SMagnet: N52H arc magnets Wire AWG: 20AWGShaft: Titanium Alloy hollow shaftStator: 0.15mm Nippon Steel silicon steelBearings: Japan EZO 8x 4 x 3mm Base casing: Al 7075 Bell cap: Al 7075 ( Double Anodizing colors )

    $25.99 $24.43, Save 6% OFF

    SKU:R5-2450

    Weight: 0.10 kg

  • X-Racer X9 Micro Racing Quad DIY Combo

    X-Racer X9 FPV flyBefore Purchasing:The X-Racer X9 does not come with the receiver. If you are using the Frsky transmitter, we suggest use FrSky XM 16 Ch Micro SBUS Receiver. If you are using other RC transmitters, you will use other mini transmitters accordingly.The camera in the combos is in PAL version. If you need the NTSC version, please leave message at the checkout, thank you.The DIY version contains the parts that you need to build, but they are not assembled yet. Please note that you will still need to purchase the battery, radio control and transmitter if you do not have them.The DIY combo  does not have the protection cover. If you need the cover pls paid 3 USD via Special Service.Following the X-Racer KL-EX90, FPV Model now has another 2" propeller 90 class micro racer. The ultralight micro racer comes with Runcam Micro Swift CCD camera which is the smallest FPV camera that use 1/3" CCD sensor in FPV community. No more blurry and dull image like youll have on other micro class. You will get the same good quality video on this micro racer like you did with normal Runcam Swift.Micro class FPV racing is more and more popular. Comparing to the regular 5" racing quads, these little stuff have many advantages. You can fly or race with them at anytime any where you like. Because they are so light in weight and so small in size, you do not need to register with FAA if you are from the United States to fly them.Equipped with the mini Raceflight Millivolt flight controller and Raceflight Spark 4n1 ESC, you will gain the best performance that you never had before. The Millivolt presents not only the BEST performance, but also the most STABLE performance due to the amazing vibration rejection technology implemented in RaceFlight. In addition to these, the X9 is equipped with the powerful Dragonfly MC1105 7500KV motors which has been proven very powerful with X-Racer KL-EX90. Features:Small in size and light in weight. All-up-weight is 83 grams only without battery. Do not require the hassles of getting it registered with the FAA if you are from the United States.2s / 3s lipo. Excellent power with just a 2S battery, even more powerful with 3S. It gives you very high speed, very precise and rail-like handling.Fast as other 5" 4S racing quads. Use Runcam Micro Swift, the worlds smallest and lightest CCD professional camera. It has the same performance to reputable Runcam Swift and Swift Mini.Equipped with the mini Raceflight Millivolt flight controller and Raceflight Spark 4n1 ESC. The Millivolt presents not only the BEST performance, but also the most STABLE performance due to the amazing vibration rejection technology implemented in RaceFlight. .Equipped with powerful and reliable micro Dragonfly MC1105 7500kv brushless motors. Gemfan 2035BN 4-blade propellers are almost unbreakable, extremely smooth and guaranteed to exceed your expectations.A Dragonfly 25mw 48ch Vtx with protective coating is inlcuded to give an even more aero dynamic low profile design for the video transmission. Parts Included:1 x X-Racer X9 Frame4 x Dragonfly MC1105 7500kv Motor1 x Raceflight Millivolt Flight Controller1 x Raceflight Spark 4n1 ESC1 x RunCam Micro Swift 2 FPV Camera (Update on September 12th.)1 x Dranonfly 5.8g 25MW 48CH Vtx4 Pairs x GemFan 2035BN 4-Blade Propellers1 x 16AWG Silicon Wire1 x Amass XT30 Plug Male16 x M2*4 Screws16 x M2*6 Screws10 x M2*7 Screws4 x M3*18 Screws7 x M2*19 Aluminum Standoff10 x M3 Black Nylon NutX-Racer X9 Brief Installation Manual: PDF DownloadFriendly reminder: The DIY version contains the parts that you need to build, but they are not assembled yet. The battery and transmitter that shown on the pictures are not included. 

    $228.00 $212.04, Save 7% OFF

    SKU:X9ARF

    Weight: 0.30 kg

  • X-Racer F4 Flight Controller

    X-Racer is making a return with an all new update. Introducing the X-Racer F4. Like we mentioned before with the X-Racer F303, the same remains true for the X-Racer F4. This board is not for everyone and is designed with simplicity in mind. If your one of the guys that tries to stay away from the AIO flight controllers then chances are high this board is for you. X-Racer F4 offers a minimalistic approach to the flight controller market while still giving you the features you need for racing and freestyle flight. This board has strong roots to the X-Racer F303 and in many ways still offers the same functionality of the previous versions with only offering two major updates. We have upgraded to an F4 processor to ensure that the CPU loads will remain low with the newest heavy hitting release of Betaflight 3.2, and we have also upgraded to include the OSD chip and give you full access to Betaflight OSD which many have come to love and cant live without. X-Racer F4 also comes with 6 PWM outputs making it an excellent choice for those of you whom may be more interested in running a hex setup for Freedom Class racing.Download Firmware:  Click HERE.Friendly reminder: Due to only the UART1 has built-in inverter for SBUS receiver, other UART 3-6 are without built-in inverters, the receiver needs to connect the TX pad of flight controller directly without using its built-in inverter.Layout of X-Racer F4 (Click to enlarge the picture)Wiring Diagram of X-Racer F4 (Click to enlarge the picture)

    $33.29 $24.97, Save 25% OFF

    SKU:XRF4FC

    Weight: 0.10 kg

  • BattleRC 60mm Micro 5.8G FPV VTX Linear Antenna Ipex 3pcs

    Specifications:Frequency: 5.7~5.9Ghz VSWR:  ≤2.5 @5700 MHz ~5900 MHzGain definition: 2dBi ( *Typical* )Band definition: 4900 MHz ~5900 MHzImpedance definition: 50 ohmSignal transmission directionality: High Gain omnidirectional antennaConnector type: Ipex connector Antenna Length: 60MM

    $12.50 $11.38, Save 9% OFF

    SKU:3RG178

    Weight: 0.28 kg

  • BattleRC Micro 5.8G FPV VTX Antenna 60mm 3pcs

    Electrical Specifications:Frequency Range (MHz): 5100-5150/5750-5800Bandwidth (MHz): 50/50Input Impendence (Ω): 50V.S.W.R: ≤1.5Gain (dBi): 2.0Polarization Type: Vertical polarizationLightning Protection: DC groundingPower Capacity (w): 50Mechanical Specifications:Antenna Length (mm): 60MM±1MMRadiator: CuprumConnect Type: WeldingWorking Temp(℃): -40~60Storage Temperature(℃): -20~40Weight (g) :0.5±1

    $12.50 $9.00, Save 28% OFF

    SKU:3FMQA

    Weight: 0.10 kg

  • Dragonfly MC1105 Micro Class Racing Motor 7500kv

    X-Racer KL-EX90 LOS Maiden Flight : Insane 2inch Power! By the RCAddictThese are the new Dragonfly MC1105 7500kv brushless motors for micro class racing quads. They have been proven powerful and reliable at race track, while our team pilot Ka Kei Leung flew the 2" KL-EX90 with these micro motors to compete with 4s 5" bigger racing quads. Click to watch the video. Recommend to use Gemfan 2-3" propellers and 12A ESCs.Dragonfly MC1105 Mini Motor Specifications:KV: 7500KVNo.of Cells(Lipo)): 2S-3SStator Diameter: 11mmStator Length: 5mmShaft Diameter: 1.5mmMotor Dimensions(Dia.*Len): Φ14.2×14.45mmWeight (g): 6gRecommended propellers: Gemfan 2-3″, Gemfan 2035BNRecommended ESC: 12A

    $9.99-$38.99

    SKU:KL90MT

    Weight: 0.10 kg

  • X-Racer KL-EX90 Micro Racing Quad Frame Kit

    KL-EX90 Indoor FPVX-Racer KL-EX90 LOS Maiden Flight By the RCAddictWarning: This frame can handle components that equal much larger mini quads, please treat it with respect. Introducing the KL-EX90! This is a frame that is designed to open your eyes to the possibility of seeing a 90mm class airframe that can compete with the “big boys” We’ve already proven it in Shanghai. We put it up against the much larger quads and placed higher than the average competitor! This frame can be an indoor flyer when paired with the correct motors but I’m afraid to say FPVMODEL doesn’t offer those motors. We want to respect the designer’s intentions, offer a small beast that can compete in professional settings. If you want docile, go Eachine. If you want performance take this frame and match it with motors designed to make it shine! Click here for an awesome motor combination. The price is for frame kit only, including the 3D printed parts. If you like the complete set, we have two combos for you: One is the BNF combo, the other is the ARF DIY combo.Package Includes:1 x KL-EX90 Frame1 x 3D Printed Camera Mount for Runcam Micro Swift 1 x 3D Printed Taillight Mount8 x ScrewsYou might also need (not included): Dragonfly MC1105 Micro Class Racing MotorFlycolor RAPTOR S-TowerRunCam Micro Swift FPV CameraDranonfly5.8g25MW 48CHGemFan 2035BN 4-Blade PropellersOrignal Amass XT30 Plug MaleCJMCU WS2812 5050 RGB LED BoardThe design of KL-EX90 is inspired by the champion KL200Race racing quad. Much smaller in size, but gives you the same flying experience of professional 200 and 210 class racing drones.

    $18.99

    SKU:KL90FKD

    Weight: 0.30 kg

  • XBEE SR Hybrid 220mm Frame Kit with PDB

    Size Guide · Wheelbase 220mm Features · Full Carbon Fiber. · 2mm Bottom Plate, 2mm Top Plate and 4mm arms · Matek PDB include(PDB-XPW W/ CURRENT SENSOR 140A & DUAL BEC) · Black steel screws(option titanium screws) · Weight : 80.4g(With titanium screws 76.9g) Includes · Carbon parts 2 x 4mm 5inch Front ARMs 2 x 4mm 5inch Rear ARMs 2 x 2mm 5inch ARM Brace 1 x 1.5mm Arm Upper Plate 1 x 2mm Top Plate 1 x 2mm Bottom Plate 1 x 1.5mm Cam mount Plate 1 x 1.5mm Cam mount(Side) 2 x 1.5mm Camera mount Sidewall width 28mm 2 x 1.5mm Camera mount Sidewall width 29mm 1 x 1.5mm Battery Protector · Hardware 6 x Matt black standoff (4 x 28mm, 2 x 22mm) 8 x 3*5mm Metalbolt 4 x 3*12mm Metalbolt 4 x 3*15mm Metalbolt 4 x M3 rubber damper o ring 4 x M3*5 Nylon post 8 x M3 Nylon nut · Parts 1 x PDB-XPW W/ CURRENT SENSOR 140A & DUAL BEC 1 x XT60

    $81.00 $72.90, Save 10% OFF

    SKU:XBSRHF

    Weight: 0.50 kg

  • XBEE SR 220mm Frame Kit with PDB

    Size Guide · Wheelbase 220mm Features · Full Carbon Fiber. · 2mm Bottom Plate, 2mm Top Plate and 4mm arms · Matek PDB include(PDB-XPW W/ CURRENT SENSOR 140A & DUAL BEC) · Black steel screws(option titanium screws) · Weight : 75g(With titanium screws 71.5g) Includes · Carbon parts 4 x 4mm 5inch ARMs 2 x 2mm 5inch ARM Brace 1 x 1.5mm Arm Upper Plate 1 x 2mm Top Plate 1 x 2mm Bottom Plate 1 x 1.5mm Cam mount Plate 1 x 1.5mm Cam mount(Side) 2 x 1.5mm Camera mount Sidewall width 28mm 2 x 1.5mm Camera mount Sidewall width 29mm 1 x 1.5mm Battery Protector · Hardware 6 x Matt black standoff (4 x 28mm, 2 x 22mm) 8 x 3*5mm Metalbolt 4 x 3*12mm Metalbolt 4 x 3*15mm Metalbolt 4 x M3 rubber damper o ring 4 x M3*5 Nylon post 8 x M3 Nylon nut · Parts 1 x PDB-XPW W/ CURRENT SENSOR 140A & DUAL BEC 1 x XT60

    $79.00 $61.62, Save 22% OFF

    SKU:XBSR2F

    Weight: 0.50 kg




Find us on Google+ Watch us on Youtube Like us on Twitter Follow us on Facebook

Home   |   About Us   |   New Products   |   Multi-Rotors   |   FPV Airplanes   |   FPV Equipment   |   Battery / Chargers   |   Tools & Accessories   |   Contact Us   |   Blog   |  Site Map

Product Tags: ABCDEFGHIJKLMNOPQRSTUVWXYZ0-9

Copyright © 2015 FPVMODEL.COM®. All Rights Reserved.