Sorted:
  • Aomway TX004 Mini 5.8G 25mw/100mw/200MW Power Switchable Transmitter

    TX004 Transmitter is a 5.8G ISM band simulation diagram transmitter with a stable output power, long-distance transmission,  powerful filter. Can guarantee the image of the maximum throttle no snow, no stripes and so on. TX004 transmitter also has the funtion of remote control the OSD interface and support for more than 8 peoples at the same time flying.Features:-Output power is stable, long-distance transmission: ≥0.5km@25mW, ≥0.8km@100mW, ≥1km@200mW (Original antenna)-Transmit power 4 block switch: 0mW/25mW/100mW/200mW-64 frequency output, has E group of eight competition frequency at the same time without interference-Fast frequency lock-With self-test output power-Video format: NTSC /PAL-Wide input voltage range, low power consumption: 7V~24V,+12V/170mA@200mW.-Small volume: 27mm×27mm×4.5mm-Light weight: ≤3g (Do not including the antenna)Frequency Table:

    $16.99

    SKU:AWTXT

    Weight: 0.10 kg

  • RunCam TX200 3.5-5.5V 5.8G 48CH 200MW Video Transmitter

    TX200 VTX is the first video transmitter from Runcam. It is super light weight and designed specifically for the Runcam Micro Swift 2 camera.The Runcam TX200 is a very simple and plain VTX, there is only one button to change channel, band and power, and some LED’s indicating what settings the VTX is on. The VTX is built on a 19x19mm square PCB and it can be mounted directly on the back of a Micro Swift or Micro swift 2 with the provided standoffs and screws.You can use this VTX as a standalone VTX too if you wish. The standoffs leave a gap between the camera and VTX PCB’s, allows for airflow and better cooling.To know more about Runcam TX200 video transmitter, you can take a reference to Oscar Liangs review.Frequency SetupLock mode:Red LED flashes, only 25mW & limited frequency available;Unlocked mode:Red LED keeps on, 200mW & all 48 channels available; By long pressing button for 10 seconds, you can switch between the two modes.Note: Before you get TX200 unlocked, it is highly recommended to know about the rules and regulations in your country about the frequency to avoid a fine or confiscation of your device.1 Blue LED for ChannelShort press the button to switch the Channel, Channel 1/2/3/4/5/6/7/8 in sequence. For each short press, the Blue LED flashes once, and only when its under the Channel 1, the LED is always on.6 Red LED for BandLong press the button two seconds to switch the Band, Band 1/2/3/4/5/6 in sequence.For each long press, the six Red LEDs light in turn.1 Orange LED for PowerLong press the button five seconds to switch the power, on is 200mw, off is 25mw, lock mode is limited to 25mw.Frequency TableParameter

    $14.99 $13.99, Save $1.00 OFF

    SKU:RCTX200

    Weight: 0.14 kg

  • Matek 5.8G 38CH 25/200/500mW Switchable Video Transmitter VTX-HV With BFCMS Control

    Mateksys is expanding their product range and releasing their own video transmitters. The first one is Matek VTX-HV. It is separate half size of a normal FC, stackable board with OSD. ‘HV’ probably stands for High Voltage, as this VTX works directly from up to 6S HV LiPo battery. Has 5V output for camera, audio input, iPEX antenna connector, LED’s for channel band and power indication and traditional button control.* Friendly reminder: the new version of VTX-HV contains 38 channels only as the channel 5945 and 5645 are not to be used in the United States. Please be aware of the difference between the text and picture descriptions. Specifications & FeaturesInput voltage: 7~27V(2~6S LiPo)38 standard channels, A/B/E/F/R BandOutput Power: 25, 200, 500mW switchableBEC Output: 5V/1A for Camera or FCTraditional button+LED control of frequency and powerBFCMS (BFOSD & LUA Script) control via FC UART _TXFirmware upgradeablePower Consumption: 3.1W Max. @ 500mWVideo Input Impedance: 75 OhmAudio Subcarrier Frequency: 6.5 MHzRF Connector: U.FL (IPEX)Video Format: NTSC/PALWeight: 6g (Tx only, w/o SMA cable)Size: 36*22*6.5mm w/30.5mm mountingU.FL version Packing5.8G Video transmitter (U.FL)PVC Heat-shrink tubeU.FL to SMA Female, RG178 cable 10cmU.FL 5.8G whip antenna, RG178 10cmMMCX version Packing5.8G Video transmitter (MMCX)PVC Heat-shrink tubeMMCX to SMA Female, RG178 cable 9cm

    $29.90 $26.91, Save 10% OFF

    SKU:VTX-HV

    Weight: 0.10 kg

  • BattleRC Pagoda 2 5.8GHz Antenna RHCP SMA / RP-SMA Optional 2pcs

    The Pagoda 2 from Battle RC is specially designed 5.8G fpv antenna on the basis of Maarten Baert circularly polarized antenna drone racing design. It is good for both video TX and video RX. The structure is made of 3 layers of PCB board, which integrated one ounce copper foil.Maarten Beart Website (Creator for the Pagoda): http://www.maartenbaert.be/quadcopters/antennas/pagoda-antenna/The Pagoda 2 5.8G antenna is an omnidirectional circularly polarized antenna design. The main advantage of Pagoda 2 antenna is the rejection rate of the dual circular polarization waves.?The Pagoda 2 is manufactured according to the Maarten Baert optimized circular polarized antenna design. It consists of 3-layer PCB in which embedded 1 ounce copper foil, replacing the original typical of the wire structure components.?This antenna weighs only 8g, heavy polyolefin heat shrinkable material wrapped to the PCB can well protect PCB. Its simplified manufacturing process keeps costs low allowing for a great low price for an antenna with high performance.Price for two pieces of Pagoda 2 antenna, one is with a size of 50mm, the other is 80mm.Features:Good omnidirectional radiation pattern.Good axial ratio.Reasonably small.Easy to manufacture within fine tolerances at low cost, even for a hobbyist.Specifications :?Brand: BattleRCType: RHCPGain: ~2dbicAxial ratio: < 1.3Bandwidth: 5.5GHz-6.05GHzRadiation Efficiency: 95%SWR: S11 < -20 dB, VSWR < 1.22 (at center frequency)Size: 80mm / 50mm?Cable: Semi-rigid RG402Connector: SMA / RP-SMA optionalWorks great as both a transmitting or receiving antennaCompatible with other styles of 5.8GHz antennasPackage Includes:1 x 50mm BattleRC Pagoda 2 5.8g RHCP Antenna?1 x 80mm BattleRC Pagoda 2 5.8g RHCP Antenna?

    $13.50 $10.80, Save 20% OFF

    SKU:MBPA

    Weight: 0.10 kg

  • Skyzone RX5803 5.8G 48CH A/V Receiver Module for FPV

    The RX5803 from Skyzone is an FM A/V receiver demodulated module that works in the ISM band of 5725-5865mHz. This receiver module adopts sigle chip design which has intergrated VCO, PLL, broadband FM video demodulation and FM sound demodulation. The RX5803 is of small size and low power consumption. It will just occupy a small part of your FPV multirotor.Simple to use. Just need to power on, plug in the audio and video cables, and connect to the antenna, then you will receive the A/V signal.Features:- 5.8G broadband FM audio and video synchronization reception.- Small size: 35*24*3.5 mm- 5V 170mA Low power consumption.- High reception sensitivity:  -95dBm- Built-in frequency phase - locked loop high stability.- Low clutter leak: Complies with CE, FCC requirements.- Direct output analog audio, video signal.- 48 channel receptionFrequency range:

    $9.99

    SKU:RX5803

    Weight: 0.10 kg

  • Dragonfly 5.8G 48CH 25/200/600mw Stackable Video Transmitter

    The sale price is only limited to 50 Qty per type.Sales qtys are limited to 4 units per customer.Hurry before they are sold out!The new Dragonfly 5.8g stackable VTX comes with 48 channels, 9-26v input and switchable between 25/200/600mw. The stackable design makes you easy to place this VTX above your flight controller. With 48 channels, no need to worry about the interference while powered on any more.Main Features:Stackable Design, easy to place above flight controller.9-26V input, suitable for multirotors of various sizes for indoor and outdoor flight.Switchable between 25/200/600mw, convenient for adapting the flying environment.Comes with 48 channels, including the Raceband.Two ways of connection: Directly plug-in or soldering.SMA and RP-SMA connectors are selectable.Heat sink design to avoid over-heated.Extension cable is selectable. (Need to purchase seperately, Clike Here to Buy)Specifications:Operating Voltage: DC 9-26VSupply Current:270MAOperating Temperature:-20℃~80℃Audio Carier Frequency:6.5MHzVideo Input Impedance:75ΩWeight:10 gramsAntenna Connector:SMA / RPSMAVideo Format:PAL / NTSCOutput Power:13~28dbmChannels:48CHFrequency Range:5362~5945MHzPort Connector:2.0 socket, 5 pinSize:35x35mmUser Manual: ?Outer Diagram:Frequency Table:

    $23.80

    SKU:GFVTX

    Weight: 0.10 kg

  • Aomway TX001 5.8G 40CH 25/200/600mW Power Switchable Transmitter

    Specification: Brand Name: Aomway Item Name: TX001 Transmitter Frequency: 5.8Ghz Power Adjustable : 5.8G Switchable 25mW/200mW/600mW Channel: 40CH 5658-5945mhz (Raceband) Wide Power Input: 6-28V Current: 12V/200mW/150mA Channel&Frequency Adjustable Button Indicator LED to show the frequency and power Mic: Swithable, when open the Mic., it will occupy one audio channel Output Voltage: 4.9-5.1V for camera Audio: Stereo Output Format: Auto regonize NTSC/PAL Connector: TX001A SMA short conenctor;TX001B 50mm SMA extend cord connector Dimension: 29x25x10mm Weight: 11g

    $34.99 $21.69, Save 38% OFF

    SKU:TX001

    Weight: 0.10 kg

  • Dragonfly Booster 5.8G 3dBi TX/RX FPV Antenna RP-SMA/SMA

    Dragonfly Booster Durability TestBetter signal quality and much more durable. These Dragonfly Booster antennas can be survived from the hardest crashes with the specially designed cover and silver connector. Three different sizes?(5cm, 8cm and 11cm) in SMA and RP-SMA are selectable to meet your special needs for the build.Specification:Frequency Range: 5400 ~ 5900MhzImpedance: 50ΩV.S.W.R: ≦1.5Gain: 3 ~ 3.5dBiFirst Upper Sidelobe Suppression (dB) ≥15Front to Rear Ratio (dB) ≥25Cross-polarization Discrimination (dB) ≥15Port Isolation (dB) ≥28Polarization: Vertical/HorizontalMaximum Input Power: 10WCable: RG141Color: BlackConnector: RP-SMA / SMA (Optional)Length: 5cm / 8cm / 11cm (Optional)Weight: 10g / 11g / 13g Package Included:?1 x Antenna* 5.8G Vertical Polarization* 5.8G Horizontal Polarization

    $15.98 $9.59, Save 40% OFF

    SKU:FBSA

    Weight: 0.10 kg

  • FPVModel Dual channel 5.8G 40 channel competitive version receiver built in DVR

    FPVModel Dual Channel 5.8G 40CH Receiver DVR FootageFPVMODELs 5.8G Explorer 40 channel dual diversity receiver. This reciever is designed for both close range and long distance flights featuring a built in DVR that can record your flights and later(if needed) be used to review flight footage to help aid in the retrieval of a lost model. The channel range covers the standard 32 channels weve all come to know over the last few years and the additional race band that has recently started to take over the miniquad scene. This is perfect for those tight indoor tracks and helps pick up a better signal where instances of multipathing are high. Comes with a standart thread that fits most tripods so this will allow for easy mounting and getting some of the height needed for better signal reception. 5.8G Explorer also features a 3.5mm jack for easy connection to your goggles. Battery straps on the back allow for easy battery storage and can accept a wide range of batteries from 2S to 6S.(7-24v) Receiver Sensitivity of -96dBm.Features:1 Receiving frequency: ISM 5.6GHz-5.95GHz 40CH2 Operating Voltage: 7.0V-28.0V3 Supply current: <300mA/12VDC4 Video Output Level: 1V±0.2Vp-p/75Ω5 Aidio Output Level: 0.5~2.0Vp-p/10KΩ 6 TV System: PAL/ NTSC / SECAM(AUTO)7 Wireless Receiver Sensitivity: <-92dBm(15dBuV)8 Antenna Connector: SMA Connector9 Weight: 212g(dvr)10 Dimensions(L*W*H): 60*150*27.5mm11 Operating Temperature: –10℃~+85℃Item Packing:1 x receiver1 x power cord1 x video line2 x antenna2 X band1 x 3.5mm audio & video plug

    $86.99 $69.59, Save 20% OFF

    SKU:FR007

    Weight: 0.70 kg

  • Dragonfly 5.8G Receiver Module for Fatshark Dominator FPV Goggles

    The sale price is only limited to 50 Qty.Hurry before they are sold out!Higher sensitivity and much more durable. Perfect for those who want to upgrade to race band.The Dragonfly 5.8G receiver module is made for the Fatshark Dominator line of goggles. The RX has been manufatured in white to match the white headset for the flyers that dont use the plastic snap cover but can also be used with the cover in place. This reciever has a built in LED to make it easier to know what channel you are on and make the channel selection process much smoother. No fooling around counting flashing lights with buttons that are too small and hard to press. Long press the button to band and use the fatshark channel buttons to cycle the channel.Quick Intructions:Place the module into your Fatshark Dominator receiver. Long press for Band, Cycle goggle channel switch for channels. The receiver will display the currently active band with the LED.- 1 flash = BOSCAM Band A- 2 flashes = BOSCAM Band B- 3 flashes = BOSCAM Band E- 4 flashes = Airwave- 5 flashes = Race bandSpecifications:1. 40 channels (5 Bands with 8 channels each)2. -90dBm sensitivity3. Works with all BOSCAM A/V transmitters (200mW, 400mW, 500mW)4. Works with Airwave transmitters (tested with the new ImmersionRC 600mW). Airwave frequency support is not full spec. Range is affected, as well as transmission picture quality! We highly recommend the use of BOSCAM transmitters.5. 3 - 5V operating voltage6. SMA antenna connector7. Fatshark Dominator compatible, toggles channels using the Fatshark button!8. Can be installed into Fatshark Attitude goggles!Supported Frequencies:

    $28.99 $14.99, Save $14.00 OFF

    SKU:RFFSG

    Weight: 0.10 kg

  • Dragonfly 5.8G 40CH Mini TX 25mw/200mw

    Introducing the new ultra light weight Dragonfly 5.8G mini video transmitter. Featuring the full range of 40 channels to ensure you can transmit on the frequency that is most convenient to you. This transmitter features a smart design with push button band & channel navigation, along side the edge of the transmitter is a power switch enabling the user to turn the tx off and on at will. This is especially helpful when connecting to the computer or powering the aircraft without the antenna on. Press once quickly to change channels, hold down with a slight pause to enter band mode and cycle through the full range of bands. Dont worry about fumbling with dip switches and channel diagrams with this smart push button design.We have 25mw and 200mw sending power for your choice. Price for single TX only.Frequency and Channel Frequency Table

    $21.99 $16.99, Save $5.00 OFF

    SKU:D58MTX

    Weight: 0.10 kg

  • HAWKEYE MINI 5.8GHZ 200MW 32CH WIRELESS A/V TRANSMITTER TX RACEBAND

    Specifications:- 5.8G FM AV sender- Power: 200mW- Built-in four frequency optional: 5740-5860MHz/5705-5925MHz/5725-5865MHZ/5685-5917MHZ(RaceBand)- 32 Channel- Dimension: 21*20*8mm- Weight: 6g(without antenna)- Stereo sound, left/right track independant transmission- PAL/NTSC supported- Interface: 10cm SMA- Wide input voltage DC6-24V

    $34.95 $32.15, Save 8% OFF

    SKU:HE58VTX-10

    Weight: 0.10 kg

  • Skyzone T600 5.8Ghz 600mW A/V Transmitter

    Skyzone T600 600mw video transmitter features "R" Band, it is 37mhz apart from the next channel (e.g. 5658, 5695, 5732, 5769, 5806, 5843, 5880, 5817mhz), this minimize jamming with another FPV player in the field.Specifications:Frequency and channel frequency table

    $49.39 $31.61, Save 36% OFF

    SKU:SZT600

    Weight: 0.20 kg

  • Tarot 5.8G 600MW 32CH Video TX/RX TL300N for FPV

    Description:- Tarot independent developing TX RX package with 32 frequency point- 600mw 5.8G telemetry system has super mini size and light weight, specially suitable for mini multirotor and QAV quadcopter- 32 frequency points are compatible with normal frequency, providing 1 channel of video signal, 2 channels of audio signal distant transmission, and also providing 5V 1A power supply outputSpecs:- TX5832-600M audio video transmitter x 1- RX5832 AV receiver x 1- 7P color pin x 1- 3.5MM power supply cable x 1- 2.5MM AV cable x 1- Manual x 1TX Parameters:- Net weight: 8.3g (antenna not included)- Dimension: 21 x 33 x 7.5 mm- Working Frequency: 5645-5945MHz- Channel: 4 bands / 32 channel- Channel: 5-DIP switch- Output Power: 27.5 dbm (600mw)- Input Voltage: DC 7-26V (2-6S)- Output Voltage: 5V 1A- Antenna Adaptor: SMA 50Ω- Working Temperature: -10 ~ 60 degrees.- FM Frequency: FMRX parameters:- Weight: 10.9 G (without antenna)- Dimension: 28 x 46 x 40 mm- Working frequency: 5645-5945 MHZ- Channel: 4 bands / 32 channels- Channel choose: 5-DIP switch- Receiving Sensitivity: -85 dbm- Input Voltage: DC 7-26V (2-6S)- Antenna Adaptor: SMA 50Ω- Working Temperature: -10 ~ 60 degrees- FM/PLL Frequency: FM/PLL- AV output: 2.5mm 4 pins AV output- Power input: 3.5mm (exterior) 1.3 mm (interior) DCNote:- Install the antenna before connecting the power to avoid further damage.- Choose proper working frequency and tune the receiver to the same frequency. Please refer to the channel list.- Do not touch the surface of transmitter while operating. It is normal the surface is getting hot.- The input voltage range is between 7-26V (2-6S), do not overload the working voltage.- The output voltage is 5V1A. Please confirm the current and voltage of the camera

    $51.65 $50.10, Save 3% OFF

    SKU:TL300N

    Weight: 0.10 kg

  • Aomway 5.8G 1000mW A/V 1W Transmitter / 5.8G 48ch Receiver Built-in DVR for FPV

    Transmitter Specifications:- Upgrade video circuit and sensitivity, with 1W telemetry, could fly 32KM- 5.8G band FM audio/video transmit synchro.- Low consumption: 12V 700mA- Power: 1000mW/30dBm- Built-in two emission frequency: 5740-5860MHz/5705-5945MHz- 15CH: CH1-7, +CH1-8- Blue semi transparent shell, more convenient for use.- Stereo, left/right audio channel independant transmission- Format: PAL/NTSC- Wide input voltage: DC7-16V- Could use 5V,12V cameras(switch through jumper)Features:- 5.8G receiver, 32 frequency point, cover almost all frequency band- Frequencyband and frequency point independant display, aovoid mistake- Upgrade video circuit and sensitivity, with 1W telemetry, could fly 32KM - Add DVR video recording function, perfect synchro.Receiver parameters:- Working Frequency: 5740-5860MHz (Fatshark dedicated ) / 5705-5945MHz ( Universal )5733-5866MHZ/5725-5865MHZ- DVR: D1 format,one channel video recording- Wide input voltage : 7V-16V- DC 12V,170mA- 15 transmit channels : CH-1 7channels CH-2 8channels- Sound: about two-channel stereo output- AV Video Output: 2 AV output- Weight : 126g- Size : 80 * 70 * 25mmUpdate on June 6th, 2017: The receivers channel have been upgraded. From 32CH into 48CH.

    $84.90 $44.15, Save 48% OFF

    SKU:A5G81WTX

    Weight: 0.50 kg

  • BOSCAM RC305 5.8G 8CH Wireless AV Receiver For FPV

    Includes an additional AV output for video recording while using FPV goggles.Specifications: Channels: 8Receiver operating voltage: 5VDCOperating temp: -10~85CVideo bandwidth: 0~8.0MHzAudio frequency: 6.5MHzVideo input level: 0.8~1.2Vp-pVideo input impedance: 75OhmAudio input level: 0.5~2.0Vp-pAudio input impedance: 10K/OhmWeight: 43gAntenna connector: RP-SMA Dimensions: 61x52x13mmChannels5.8G : 5705,5865,5665,5645,5885,5905,5925,5945MHZApplications Rc Hobbies Remote control aircraft Remote spacecraft Remote control toys

    $28.90 $8.09, Save 72% OFF

    SKU:RC305

    Weight: 0.10 kg

  • D58-2 5.8GHz 2-way 32CH Dual Diversity Receiver

    Diversity is the ultimate FPV solution, allowing the end user to use 2 different antennas to provide the very best in range and redundancy. With a Diversity system, you can utilize 2 differing styles of antennas, such as an omni-directional antenna, and a flat patch, panel antenna, which provides you with long range in a very directional locale. With (2) differing antenna styles, this will allow you to expand your FPV range in new ways, providing a more layered FPV experience.With the Duo Diversity system, your receiver will automatically choose the receiver with the greater signal strength, automatically switching to the best channel that is receiving your FPV video signal. This allows you to use (2) styles of antennas that provide differing signal patterns, which will optimize your FPV experience.The ultimate 5.8Ghz 32CH wireless audio video solution. These receivers allow you to use 1 receiver for 2 transmitters at the same time. These D58-2 receivers also support "Diversity Mode", meaning one receivers with 2 different polarized antennas or 2 different types of antenna to COMPARE & SWITCH automatically for receiving the best video signal.  It is the ultimate solution when you have two high gain directional antennas or one stock antenna with one high gain antenna installed to a  D58-2 receiver.  In addition, if you have an auto antenna tracker, these receivers are the must for you antenna tracker!Product Note: Do not power up receiver unit without antennas - by doing so, you will damage the receiver, and this will void warranty in full. DS58-2 Features:*  Dual receiver system with auto switching for best signal clarity*  Triple, buffered AV outputs*  Can receive 2 different channels at the same time*  Not affect by 2.4GHz R/C transmitters*  AV Receiver with Diversity inputs*  Small, light weight and durable, with anodized aluminum housing Specifications: Video Output: 75Ω/1VppAudio Output: 10KΩ/500mVp?pTV Scanning System: PAL/NTSC/SECAMInput Voltage: 12V/500mAWeight: 197gDimensions: 76mm x 64mm x 18mmIncluding items of D58-21 x Wireless 5.8GHz AV Receiver D58-22 x Stereo jack to RCA AV output cable1 x JST Power Core2 x Stock dipole antennasTo receiver two different channels at the same time (one receiver two transmitters mode)Mount both antennas on, either the stock ones or yours.Connect the AV cables to the AV output AV1 & AV2, and connect the antennas,and then apply the power.Select the channel:RX1 for Rf1 and RX2 for RF2,with different position of the number 1,2,3 names different channels.operation for Diversity use:1.connect the AV cables to the AV output:tracker link,and connect the antennas,and then apply the power2.the Band A,B,E or F frequencies by switch 7 and 8 3.LED4 for RF1 and led3 for RF2. The LED will be be on when the strongest signal is confirmed.It will automatically switch to the receiver with the strongest signal.RECOMMENDED ITEMS FOR D58-2 BosCam TS-351 5.8GHz 200mW Wireless AV TransmitterBosCam TS-352 5.8GHz 500mW Wireless AV TransmitterBosCam TS-353 5.8GHz 400mW Wireless AV TransmitterBOSCAM TX51W 5.8GHz 1000mW FPV Transmitter5.8G High Gain Directional Panel Antenna 

    $79.99 $70.39, Save 12% OFF

    SKU:D58-2

    Weight: 0.20 kg

  • rx5808 5.8G wireless audio and video receiver module for fpv

    5.8G wireless audio and video receiver moduleDescription:Receive Frequency: 5725-5865MHz; 8 channelsReceiver sensitivity:-90dBmFrequency Control: Built-in PLLDual AV output: output analog audio and video signals directlyAntenna interface: SMA (the pin)Supply voltage: 5VSupply Current: 150mA8-channel receiverCompatible with the transmitter module 5.8g200mw or 5.8g20mw

    $14.00 $6.30, Save 55% OFF

    SKU:RX5808

    Weight: 0.10 kg

  • 5.8G 200mW wireless audio and video transmitter module

    Specifications:Brand Name: Boscam Model Number: TX5823Transmitter frequency: 5705-5945MHz;8CH Transmitting power: 23dBm/200mW Transmitting distance: >2000mPower supply voltage: 3.3-3.5V Supply current: 320mA Dimension: 18*18*4mm5.8G 200mW wireless audio and video transmitter module    Brief descriptions:a.transmitter frequency: 5705-5965MHz; b.transmitting power:23dBm /200mWc.transmitting distance: further than 2000 metresd.frequency control:built-in frequency and phase lock loope.AV input:analog AV signal inputf.power supply voltage:3.2-3.4Vg.supply current:320mAh.dimension:18*18*4mm  It can be mating with RX5808 receiver module. 

    $19.00 $6.08, Save 68% OFF

    SKU:5200TXM

    Weight: 0.10 kg

  • D58-4 4way 5.8G 8CH A/V Diversity Receiver

    4 in 1 5.8GHz Diversity video audio Receiver D58-4Specifications:Receiver Frequency:CH1: 5705MHz CH2: 5685MHz CH3: 5665MHz CH4: 5645MHzCH5: 5885MHz CH6: 5905MHz CH7: 5925MHz CH8: 5945MHz Video Output: 75Ω/1Vp-pAudio Output: 10KΩ/500mVp-pTV System: PAL/NTSC/SECAMInput Voltage: 12V/500mAWeight: 240g(without cables) Features:- Features of D58-4 5.8G 8Channel Diversity Receiver:- Four channel Receiver for best reception- Four groups frequencies can be offered- Automatic Antenna Switching- Triple, buffered AV outputs- Can receive 4 different channels at the same time- Not affect by 2.4GHz R/C Radios- AV Receiver with Diversity inputs- Small, light weight,four way,anodized aluminum caseHow to use: To receive 4 different channels at the same time:① Connect the antennas then connect the AV cables to: AV1,AV2,AV3,AV4, and then connect the 12V DC power adapter.② Switch on the power button,LED1,LED2,LED3,LED4 are on means the 4Ch RF are working. LED5, LED6, LED7, LED8 are all on and AV1, AV2, AV3, AV4 are then ready to work.LED8 is on when no signal.③ Select the channel: RX1 for RF1 and RX2 for F2, RX3 for RF3, RX4 for RF4, with different position of the number 1, 2, 3 names different channels from CH1 to CH8.Operations for Diversity use:① Connect the AV cable to AV5, and connect the antennas, and then apply the power.② Switch on the power button.③ Set RX1, RX2, RX3, RX4 to the same channel.④ LED5 for RF1 and LED6 for RF2,LED7 for RF3,LED8 for RF4. The LED will be on when the strongest signal is confirmed. It will automatically switch to the receiver with the strongest signal. 

    $188.50 $135.72, Save 28% OFF

    SKU:D58-4R

    Weight: 0.50 kg

Find us on Google+ Watch us on Youtube Like us on Twitter Follow us on Facebook

Home   |   About Us   |   New Products   |   Multi-Rotors   |   FPV Airplanes   |   FPV Equipment   |   Battery / Chargers   |   Tools & Accessories   |   Contact Us   |   Blog   |  Site Map

Product Tags: ABCDEFGHIJKLMNOPQRSTUVWXYZ0-9

Copyright © 2015 FPVMODEL.COM®. All Rights Reserved.