• Dragonfly Low Profile Micro FPV Camera

    This is the micro FPV camera that we are using on the hot selling X-Racer X-1. Using this high quality micro FPV camera, we have saved some much needed space for this design and we are able to place the camera in a low profile position between the two forward motors allowing for a design that does not require the video system being mounted in a high profile top mount of the aircraft.Specifications:CCD 1/4 CmosSignal System PAL NTSCPixel P:720H×576 N:720×487Photosensitive area 1/4:4.077mm x 3.136mm Scanning frequency H:15.625KHz V:50Hz H:15.7343KHz V:60HzHorizontal clarity 800 TV LinesShutter Speed 1/50-1/100000(秒) 1/60-1/100000(秒)Min. Illumination 0.1 Lux / F1.2S/N radio ≥48dB(AGC OFF)Grayscale 10Gamma value 0.45Black level 0.06 Vp-pVideo output 1.0Vp-p 75ΩPower Requirement DC3.3-5VWorking Temperature -20℃~50℃ RH95% MaxPower Consumption 90MA

    Review: Write a Review



    Weight: 0.10 kg

  • Dragonfly 25mw 48CH Micro VTX For X-Racer X-1 and KL-EX90

    FPVModel did not stop at the flight controller design. We have also designed a Drgonfly 25mw 48ch Vtx to mount flushly on top of the FC and give and even more aero dynamic low profile design for the video transmission. By using this low profile design were able to streamline the body of the X-Racer X-1 and allow for smooth airflow over the low slung canopy, allowing for smooth airflow over the top of the frame.

    Review: Write a Review



    Weight: 0.10 kg

  • Dragonfly Transmitting SMA Female Antenna Extension Cables

    Dragonfly Transmitting SMA Female Antenna Extension Cables. A simple extension cable for better placement of your antenna.Specifications:- Connector: SMA Female- Cable Length: 45mm (cable only)

    Review: Write a Review



    Weight: 0.10 kg

  • Dragonfly 7x16mm 14000KV Coreless Motor for X-Racer X1

    These are powerful 7mm motors that works great in X-Racer X-1 like micro racers. These motors come with plug and 8cm wire, they are better suited to FPV and will be the perfect upgrade for your Tiny conversion. If you are looking for punch and durability, you found it. Description:Motor Diameter: 7mmMotor Length: 16.5mmShaft Diameter: 0.08mmCable Length: 80mmWeight: about 3.2gOption: CW Motor(With Red Black wire), CCW Motor(With Black White wire)Quantity: 1pc / 4pcs(2CW+2CCW) optional

    Review: Write a Review



    Weight: 0.10 kg

  • Dragonfly Booster 5.8G 3dBi TX/RX FPV Antenna RP-SMA/SMA

    Specification:Frequency Range: 5400 ~ 5900MhzImpedance: 50ΩV.S.W.R: ≦1.5Gain: 3 ~ 3.5dBiFirst Upper Sidelobe Suppression (dB) ≥15Front to Rear Ratio (dB) ≥25Cross-polarization Discrimination (dB) ≥15Port Isolation (dB) ≥28Polarization: Vertical/HorizontalMaximum Input Power: 10WCable: RG141Color: BlackConnector: RP-SMA / SMA (Optional)Length: 5cm / 8cm / 11cm (Optional)Weight: 10g / 11g / 13g Features:Better signal quality and much more durable. These antennas can survive from the hardest crashes with the specially designed cover and silver connector. Three different lengths (5cm, 8cm and 11cm) are selectable to meet your special needs for the build. Package Included: 1 x Antenna* 5.8G Vertical Polarization* 5.8G Horizontal Polarization

    Review: Write a Review

    $15.99 $13.59, Save 15% OFF


    Weight: 0.10 kg

  • New Dragonfly MC2206 2800KV Brushless Motor

    These are updated version of Dragonfly MC2206 2800KV motors that released in June 2016. They are powerful, reliable, and quick, specially designed for FPV racing mini quads that need punchy motors and the higher KV to spin those 4045 props that bit faster. The higher KV and electrical ratings allow these motors to deliver more thrust compared to other existing motors on 4 inch propellers.The new Dragonfly MC2206 2800KV motor does not come with the prop adapter, but comes with a locknut. Not only save the weight for better racing performance, but also more reliable and easier to use. This version is without the c-clip, but with a locked design at the bottom, no need to worry about the motor will drop out during racing.    Weight: 32gInternal Resistance: 0.013ΩKV Rating: 2800KVAll Dragonfly motors come with a Satisfaction Guarantee. If for any reason you are not COMPLETELY 100% SATISFIED, you can return the motors for a full refund within 30 days upon receiving them.

    Review: Write a Review

    $15.99 $10.39, Save 35% OFF


    Weight: 0.10 kg

  • Dragonfly 5.8G Receiver Module for Fatshark Dominator FPV Goggles

    Higher sensitivity and much more durable. Perfect for those who want to upgrade to race band.The Dragonfly 5.8G receiver module is made for the Fatshark Dominator line of goggles. The RX has been manufatured in white to match the white headset for the flyers that dont use the plastic snap cover but can also be used with the cover in place. This reciever has a built in LED to make it easier to know what channel you are on and make the channel selection process much smoother. No fooling around counting flashing lights with buttons that are too small and hard to press. Long press the button to band and use the fatshark channel buttons to cycle the channel.Quick Intructions:Place the module into your Fatshark Dominator receiver. Long press for Band, Cycle goggle channel switch for channels. The receiver will display the currently active band with the LED.- 1 flash = BOSCAM Band A- 2 flashes = BOSCAM Band B- 3 flashes = BOSCAM Band E- 4 flashes = Airwave- 5 flashes = Race bandSpecifications:1. 40 channels (5 Bands with 8 channels each)2. -90dBm sensitivity3. Works with all BOSCAM A/V transmitters (200mW, 400mW, 500mW)4. Works with Airwave transmitters (tested with the new ImmersionRC 600mW). Airwave frequency support is not full spec. Range is affected, as well as transmission picture quality! We highly recommend the use of BOSCAM transmitters.5. 3 - 5V operating voltage6. SMA antenna connector7. Fatshark Dominator compatible, toggles channels using the Fatshark button!8. Can be installed into Fatshark Attitude goggles!Supported Frequencies:

    Review: Write a Review

    $28.99 $26.67, Save 8% OFF


    Weight: 0.10 kg

  • Dragonfly 5.8G 40CH Mini TX 25mw/200mw

    Introducing the new ultra light weight Dragonfly 5.8G mini video transmitter. Featuring the full range of 40 channels to ensure you can transmit on the frequency that is most convenient to you. This transmitter features a smart design with push button band & channel navigation, along side the edge of the transmitter is a power switch enabling the user to turn the tx off and on at will. This is especially helpful when connecting to the computer or powering the aircraft without the antenna on. Press once quickly to change channels, hold down with a slight pause to enter band mode and cycle through the full range of bands. Dont worry about fumbling with dip switches and channel diagrams with this smart push button design.We have 25mw and 200mw sending power for your choice. Price for single TX only.Frequency and Channel Frequency Table

    Review: Write a Review

    $21.99 $16.05, Save 27% OFF


    Weight: 0.10 kg

  • Dragonfly Bulletproof Bullnose 4045 Propellers 4 pcs

    Dragonfly Bulletproof Bullnose 4045 Propellers are specially designed for mini multirotors, like ZMR180. They are composite props with a slight change in mixture, offer extra strength when compared to other propellers.  Color: Black / Green (optional)Size: 4*4.5Weight:3.5g/pc  ( update the weight on Octorber 13th)Quantity: 4 pcs (4pcs are the same rotation direction, CW/CCW optional)

    Review: Write a Review

    $3.65 $1.97, Save 46% OFF


    Weight: 0.10 kg

  • Dragonfly MC1306 3100KV Power Combo

    Note: The color of the propeller that included in this packages is optional, if you need the other color, please leave your comments at the checkout page. Thank you. Update on September 8th,  2016: Due to the SN20A ESC out of stock, we have changed the ESC to XS20A. The same price and same performance. Please make sure you understand and accept this before purchasing, thank you!Package including:Dragonfly MC1306 3100KV Mini Motor x 4 (2CW+2CCW)DYS XS20A Mini ESC x 4 4045 Electric Propeller x16 pcsMatek PDB BEC-5V x 1

    Review: Write a Review

    $89.69 $80.72, Save 10% OFF


    Weight: 0.50 kg

  • Dragonfly MC1306 3100KV Mini Motor CW/CCW

    These are the all new Dragonfly MC1306 KV3100 motors for small 180~220mm multirotors and 4~5 inch props, like RTS200. These motors are powerful, reliable,  and quick! DescriptionName: Dragonfly MC1306 3100KV Mini MotorKV: 3100Configuration: NPStator Diameter: 18mmStator Length: 14.1mmShaft Diameter: M5Motor Dimensions(Dia.*Len): Φ18×15.1mmWeight (g): 12gNo.of Cells(Lipo): 2-3SMax Continuous current(A): 7.9AMax Continuous Power(W): 58.5WAll Dragonfly motors come with a Satisfaction Guarantee, if for any reason you are not COMPLETELY 100% SATISFIED you can return the motors for a full refund within 30 days upon receiving them.  

    Review: Write a Review

    $10.99 $8.24, Save 25% OFF


    Weight: 0.10 kg

  • Prop Adapter for Dragonfly 1806 Motor CW/CCW

    Prop adapter for Dragonfly 1806 motor,A replacement for the 1806 motor,if yours lost or broken,you can buy it from here.CW or CCW thread,choose which you need.Note:This prop adapter also compatible with FPVMODEL 1806 2300KV motor or Dragonfly and FPVMODEL 2204/2206 motors.

    Review: Write a Review

    $3.00 $2.88, Save 4% OFF


    Weight: 0.05 kg

Find us on Google+ Watch us on Youtube Like us on Twitter Follow us on Facebook

Home   |   New Products   |   Multi-Rotors   |   FPV Airplanes   |   FPV Equipment   |   Battery / Chargers   |   Tools & Accessories   |  Site Map


Copyright © 2015 FPVMODEL.COM®. All Rights Reserved.