Sorted:
  • Runcam TX200U 5.8G 48CH 25mW/200mW Video FPV Transmitter VTX Support Betaflight FC For RC Drone

    ParameterPackage1 X TX200U1 X Set of screwsUser Manual : https://www.runcam.com/download/RunCam_TX200U_manual.pdf

    $17.99

    SKU:RCTX200U

    Weight: 0.10 kg

  • BetaflightF7 RV1 Flight Controller

    Friendly Reminder: Upon receiving your FC, please connect to USB and calibrate before continuing to build and solder to it.  Betaflight F7 is here and it features a completely new layout. Top mounted solder pads ensure ease of access for the even the trickiest of builds. The Betaflight F7 features dual gyros so the user can have their choice of which one to use, either the tried and true MPU6000, or the ICM20608. You’ll find the specs listed below:Specifications:3-6s Simplistic LayoutTwo Gyro optionsBetaflight OSDFiltered output for FPV systemsSmart Audio/Tramp Telemetry compatibily4 uarts (can read inverted and univerted signals)Camera Control BuzzerBlackbox via flash memory Maximum current and voltage output of LED pads: 2A, 5V30.5x30.5 FC mountingBetaflightF7 Setup Guide: Features: Programmable LEDs, Flash Memory, individual pad for camera control, labeled Smart Audio/Tramp TX1 next to VTx soldering pads. Labeled Smart Port TX2 pad next to Sbus/Ibus/DSM2 UART6 Tx, 5v and 3.3v pads (user selection based on type of receiver used), four pads for ESC telemetry connected to RX1.(Each pad placed near corners of the board) By Philipp Seidel, Click to Enlarge

    $59.99

    SKU:BFF7

    Weight: 0.10 kg

  • BetaflightF4 Flight Controller

    BetaflightF4 How to ESC Telemetry, Smart Port Audio, Smart Port TelemetryFriendly Reminder: Upon receiving your FC, please connect to USB and calibrate before continuing to build and solder to it.  BetaflightF4 is the follow up design to the very popular BetaflightF3. Following in the same path as Betaflight F3 we have kept a very similar footprint in terms of design with a few added modifications. The F405 has replaced the F303 to allow for lower CPU loads.We have eliminated the 5v/3.3v jumper and added two seperate connection points, one for sbus and one for spektrum users. The jumper still remains for the battery voltage/5v connection for connecting your camera. While wiring the board it is recommended to get power for your vtx either from a different 5v source on the board or if using a higher voltage vtx power it from the battery input coming into the pdb. Running ground loop at Agnd with gnd wires from camera and vtx is still recommended to give the cleanest video signal. Another small design change to this board was changing the BEC, this change takes the recommended 5v 2A current limit and drops it down to 5V 1.5A, its a small change but one that we opted for in order to use a more reliable BEC.BetaflightF4 now comes with telemtry pads for BLHeli32 ESCs these pads are located between the signal and gnd pads for the ESC connections.FeaturesIntegrated PDBBuilt in OSD customizable via Betaflight OSDCurrent sensorIntuitive layoutFlash memory for blackboxTailored to support BetaflightWhen running 8K/8K, CPU usage remains lowSpecificationsF405 ProcessorMPU6000 Gyro/ACC SensorBEC Max current 5V 1.5ABuilt in OSD – configurable via Betaflight GUICurrent sensorPower distribution board with six-layer PCBOSD Max Current: 145AWiring Diagram - Click to enlarge!BetaflightF4 Connection Plan by Phillip SeidelBetaflightF4 Turtle Mode SettingBetaflightF4 OSD FlashingHow to Use ESC TelemetryBetaflightF4 Can not ArmHow to Use Smart Port TelemetryHow to Use BetaflightF4 IBUSThe Number of “Scale the Output Voltage to Miliamp” in BetaflightHow to Set Tramp HV VTXIf you are meeting a problem with the use of flight controller and can not find the answer, please submit your question.

    $44.73 $33.99, Save 24% OFF 3

    SKU:BFF4

    Weight: 0.10 kg

  • Betaflight Hive Backpack

    For EU customers, please order on China stock and we will ship your order from EU warehouse. (EU site is temporarily unavailable for ordering due to technical issues)"Woooow Super Super Nice Betaflight BackPack!! "MinChan Kim, Professional Pilot"WOW the build quality and attention to detail relating to FPV needs is amazing, also very well packed so it arrived without a dent or scratch."James Bowles, Professional Pilot"This is a great bag,it is top level sewing and zipper,very good quality...I love my bag and I do not regret. "Kevin Reny, Professional Pilot"Testing itout right now in Sebring, 2 International flights so far, fits in overhead on737 ad 787, on the 787 you can even get it under the seat in front of you!"Paul Bitmatta, Professional Pilot"Best FPV Backpack (Betaflight Hive Backpack)!"Evgeniy Kravets, Professional Pilot"I can put everything into the Betaflight backpack with extra space!"Kakei Leung, Professional PilotBetaflight FPV Backpack | BEST FPV BACKPACK? By Joshua Bardwell* Before Purchasing: For US and EU customers, we will ship your orders from local warehouses. For all other countries, we offer free shipping on the backpack by EMS only. For some areas where EMS can not reach, we might change to ship via another shipping company.This is the Betaflight Hive Backpack. The design of this bag has taken many months and even after we released it for pre-orders, customer suggestions kept making us go back to the "final" prototype and add some of their suggestions. In reality, this is not just a backpack that was designed by us but its more of a backpack that has been designed and then re-designed by users like you. We do our best to listen to your feedback and that is proven in the design of this backpack. Requests for hard shell covers, reverse the orientation of the side pockets, make the hand held carry bgk into a liposafe fire-resistant bag are just a few of the suggestion that we went back and updated during the design process. After reviewing the final, final prototype we here at FPV Model feel like the user sugguestions weve received from our clients and friends on facebook, have helped make certain that this bag has the best quality and features available. We think youre gonna like them. The overall design of this backpack is geared towards those that are serious fliers and have multiple quads and many tools and accessories that they carry with them while traveling by air or even just to the local field. Betaflight Hive Backpacks are performance tested, at fully loaded capacity, using our strict control standards. Before we offer this product for sale, it is put through test to ensure it’s strength, durability, and dependability that is represented by the most demanding frequent travelling quad pilots. This attention to quality results in us (FPV Model) and (Betaflight) being able to offer the best warranty in the industry. Click here for the backpack warranty or download the PDF.Features:International carry-on size compatibility for air travel. Dedicated lap-top pocketDedicated fireproof lipo bagElastic daisy chain tool panel for your hex drivers and other hand held tools. Large interior pocket for carrying props with hard shell cover on the bag for added protection from outside forces. 1680D ballistic nylon bag material for long life durability. Featuring the best zippers in the market made by YKK to ensure long lasting zipper life. Contoured adjustable padded harness with height adjustable chest strap. Rain cover that pulls out from bottom panel pocket for fast rain protection.Exterior Dimensions:  56 x 34 x 18cmLarge interior pocket for carrying props with hard shell cover on the bag for added protection from outside forces.Interior and Exterior FPV Quad mounting locations.While we were designing the Betaflight backpack one thing kept coming up in the design aspect was how much room the transmitter took up inside the bag. So, we thought the best design would be to make a hard shell top mounted case on the top of the bag. The hard shell top of the case allows for extra protection of your transmitter and frees up valuable space inside the bag. The interior of the bag is very similar to other DSLR style camera bags and allows for multiple design layouts by using cushioned dividers that velcro in place and let each user layout their own custom setup based on their specific needs. Featuring the best zippers in the market made by YKK to ensure long lasting zipper life. Dedicated fireproof lipo bag to store your Lipos, no need to worry about the safety of batteries now. Still Plenty room to store your FPV accessories, you are able to carry up to 30 1500mAh batteries!!!Dedicated laptop pocketWe pay attention to every detail of the backpack. The inside fabrics come with Betaflight Logo. Plenty room to put your little stuff inside.The Betaflight Hive Backpack comes with a waterproof cover that placed in the bottom pocket. You can take it out from the backpack for added protection in case it is raining.Decent custom packaging box.Comes with a GoPro mount, recording every wonderful moment has never been so easy.  (GoPro camera not included)**** Friendly reminder: Price for Betaflight HIVE backpack only. Above pictures for demonstration purpose that the quads, tools, GoPro and other accessories are not included.

    $199.99    4

    SKU:BFBP

    Weight: 4.00 kg

  • Betaflight 32Bit 35A 2-6S BLHeli_32 ESC Dshot1200

    *** This is the new updated version of Betaflight BLHeli_32 ESC that comes with a line of soldering along the ESC sides for a better protection and giving more power. We are at it again and the guys at Betaflight, FPV Model, BLHeli, and Airbot have come together to create a version of BLHeli_32 ESCs that FPV Model hopes will not disappoint. Introducing a fresh take on an ongoing development with BLHeli_32 we are introducing BetaBees, BlHeli_32 ESCs designed in conjunction with Airbot.BLHeli_32 is the third generation BLHeli code, following base BLHeli and BLHeli_S. It runs on an ARM 32bit MCU, initially it will be on a Cortex-M0 running at 48MHz, but there are MCUs out there that can run a lot faster.  BLheli_32 can run input signals with lower latency at faster rates. Dshot up to at least Dshot1200, and at rates up to at least 32kHz is now supported.Here is what BLHELI_32 has to say about their new "Power to perform":Programmable PWM frequency of up to 48KHzAuto-timing for higher efficiency and reliabilityVoltage/Current limitingAdjustable “Brake on Stop” forceImprove direction change in Bidirectional modeESC TelemetryConfiguring from FC using DShot commandsFeatures: Built in Current SensorExtra capacitors to help smooth noisy envrionments.Customizable color choice RGB LED using Blheli_32 software.Large positive and ground pads for easy soldering. 2-6s Lipo input35A continuous current  (can handle burst above 45A but please be reasonable, do not overwork  your motors)TX pad on ESC used for Telemetry pad. (connect to FC and you would get current sensing, motor RPM, ESC temperature etc)Specifications :Input: 2-6s LiPolyConstant: 35 AmpsBurst: 45 AmpsBEC: No BEC, OPTO onlyDimensions: 34x16x7mmWeight: 6g (without motor wires)Includes:1 x Betaflight BLHeli_32 35A ESC1 x 16AWG Red Silicon Wire 10cm1 x 16AWG Black Silicon Wire 10cm3 x 20AWG Black Silicon Wire 10cm1 x 26AWG Red Silicon Wire 10cmSome Tips:BLHeli_32 ESC Firmware OverviewHow to Connect BLHeli_32 ESC to Congigurator BLHelisuite32 via FC PassthroughWhat is Dshot1200 and Why Dshot1200 is Better?How to Get Dshot1200 Running in Betaflight?Downloads:Download the latest BLHeli_32 Configurator here.Download the BLHeli_32 User Manual here.Download Betaflight 3.2.0 here.We have made a slight change to the second version of Betaflight 32bit BLHeli ESC. The soldering of previous version already connected while the new version not, so as to make the wiring cleaner.

    $18.99 $16.90, Save 11% OFF 1

    SKU:BFESC3

    Weight: 0.10 kg

  • BetaflightF3 Flight Controller

    BetaflightF3 Flight Controller | REVIEW AND HOW TO by Joshua BardwellBetaflightF3 is the flight controller designed to use every possible feature of Betaflight. More than the last half year has been spent in development. Boris B has worked with us to go over features and design aspects to help give us insight into what betaflight users want/need. This board features a 3A power draw giving users extra room for added attachments through uart ports. The six layer PCB is a more expensive design approach but was needed to give the ability to have a PDB that was capable of having wiring pads on both the top and bottom of the board. By using the six layer design we were able to increase the size of the pads and work around all the components all the while giving esc connections in the corners of the board rather than bunching all connections on either the top OR the bottom. Featuring a fully functioning OSD that can be configured in Betaflight this board will make configuring your OSD a breeze. The team at betaflight have been hard at work developing DSHOT and this board is also compatible with the latest release. But we didn’t stop there, this board also features a micro adapter to accept TF cards for those of you that like to follow up your flights with reviewing black box logging...we think we know of at least one guy that will like that. FeaturesIntegrated PDBBuilt in OSD customizable via Betaflight OSDCurrent sensorIntuitive layoutSD card slot for BlackBoxTailored to support BetaflightWhen running 8K/8K, CPU usage remains lowSpecificationsF3 ProcessorMPU6000 Gyro/ACC SensorBEC Max current 5V 2ABuilt in OSD – configurable via Betaflight GUISD Card adapter for BlackBoxCurrent sensorPower distribution board with six-layer PCBOSD Max Current: 145AWeights 8.6g***Note: Please do not connect to any equipment with the loading over 1.5A.Friendly Reminder: Choosing your power supply for video is relatively simple. Betaflight FC has two options, 5v and battery voltage. Choose your camera voltage by jumping RAM with either the 5V solder section or the Vbat solder section. (its recommended to use Vbat, Most cameras and Video transmitters can run off battery voltage) If using 5v it is recommeded to only power your camera and get the power for Vtx from another source. 

    $42.99 $29.66, Save 31% OFF 3

    SKU:BFF3

    Weight: 0.10 kg

Find us on Google+ Watch us on Youtube Like us on Twitter Follow us on Facebook

Home   |   About Us   |   New Products   |   Multi-Rotors   |   FPV Airplanes   |   FPV Equipment   |   Battery / Chargers   |   Tools & Accessories   |   Contact Us   |   Blog   |  Site Map

Product Tags: ABCDEFGHIJKLMNOPQRSTUVWXYZ0-9

Copyright © 2015 FPVMODEL.COM®. All Rights Reserved.