Found 8 results for "BLHeli_32" under the categories below:

Mini-Quad HQ
Mini ESCs
Flash Deals
Special Sale
ESCs
X-Racer Products
Betaflight Products
Sorted:
  • DYS ARIA 35A 3-6S Blheli_32 Dshot1200 ESC

    It is always better late than never. Finally the DYS Aria 35A BLHeli_32 ESC is officially launched. If you are still running its XM30A, this could be a very good upgrade for the BLHeli_32 goodness.DYS ARIA 35A 3-6S Blheli32 Dshot1200 ESCSpecifications:Current Rating: 35A (40A burst)Voltage Rating: 3S to 6SDimension: 32mm x 16mm x 5mmWeight: 4.73g bare PCB, 8.1g with wiresCurrent sensing and limitingBuilt-in Programmable RGB LEDPrice: $15.99 eachSupports DShot1200 and older ESC protocolsFeatures:With 32bit ARM Cortex MCU STM32F051 48MHZ micro processor, throttle 2048 resolution ratio, strong anti-interference capacity.Built-in sensor can be reaction of temperature, output power, output current etc, also programmable for protection.Support Blheli_32 firmware, can use the signal wire to upgrade the firmware or change the configuration on line.Current Meter to help show current indication of OSDWith USB linker can be programmable throttle setting like support positive and negative, two way mode, FPV 3D mode, motor speed, braking, PWM frequency, inlet angle speed setting, onboard RGB LED for customize color, Beep etc.It use the self-adaption control system,can go automatic with the all kind of the motor in the market,at the mean time it support up to 500HZ PWM, oneshot 125, oneshot 42, Multishot and Dshot 150/300/600/1200.With special optimize in multi-axis, the motor can launch smoother in a good throttle curve, fast response,great power, and highly support the multi-axis,fixed-wing and helicopter.The twisted-pair signal wire can lower the crosstalk inside cooper wire when it transfer,which will make the flight more stable.MCU hardware,Driver circuit, Mosfet will come with double voltage protection.To adopt the new process MOSFET of low internal resistance, will help increase resistance to flow. Also, the professional MOS driver chip makes the best efficiency.Mosfet is covered with aluminum sheet for cooling,which can bring more efficiency and stability.With special process of 6 layer thicken PCB will lower resistance, small calorific value and bigger impact resistance current.Nice optimize layout of the components and parts makes a smaller size, lighter weight and easy to build.

    $15.99 $14.39, Save 10% OFF

    SKU:DA35A

    Weight: 0.10 kg

  • Betaflight 32Bit 35A 2-6S BLHeli_32 ESC Dshot1200

    *** Update on Sept 12th, 2017: This is the new updated version of Betaflight BLHeli_32 ESC that comes with a line of soldering along the ESC sides for a better protection and giving more power. We are at it again and the guys at Betaflight, FPV Model, BLHeli, and Airbot have come together to create a version of BLHeli_32 ESCs that FPV Model hopes will not disappoint. Introducing a fresh take on an ongoing development with BLHeli_32 we are introducing BetaBees, BlHeli_32 ESCs designed in conjunction with Airbot.BLHeli_32 is the third generation BLHeli code, following base BLHeli and BLHeli_S. It runs on an ARM 32bit MCU, initially it will be on a Cortex-M0 running at 48MHz, but there are MCUs out there that can run a lot faster.  BLheli_32 can run input signals with lower latency at faster rates. Dshot up to at least Dshot1200, and at rates up to at least 32kHz is now supported.Here is what BLHELI_32 has to say about their new "Power to perform":Programmable PWM frequency of up to 48KHzAuto-timing for higher efficiency and reliabilityVoltage/Current limitingAdjustable “Brake on Stop” forceImprove direction change in Bidirectional modeESC TelemetryConfiguring from FC using DShot commandsFeatures: Built in Current SensorExtra capacitors to help smooth noisy envrionments.Customizable color choice RGB LED using Blheli_32 software.Large positive and ground pads for easy soldering. 2-6s Lipo input35A continuous current  (can handle burst above 45A but please be reasonable, do not overwork  your motors)TX pad on ESC used for Telemetry pad. (connect to FC and you would get current sensing, motor RPM, ESC temperature etc)Specifications :Input: 2-6s LiPolyConstant: 35 AmpsBurst: 45 AmpsBEC: No BEC, OPTO onlyDimensions: 34x16x7mmWeight: 6g (without motor wires)Includes:1 x Betaflight BLHeli_32 35A ESC1 x 16AWG Red Silicon Wire 10cm1 x 16AWG Black Silicon Wire 10cm3 x 20AWG Black Silicon Wire 10cm1 x 26AWG Red Silicon Wire 10cmSome Tips:BLHeli_32 ESC Firmware OverviewHow to Connect BLHeli_32 ESC to Congigurator BLHelisuite32 via FC PassthroughWhat is Dshot1200 and Why Dshot1200 is Better?How to Get Dshot1200 Running in Betaflight?Downloads:Download the latest BLHeli_32 Configurator here.Download the BLHeli_32 User Manual here.Download Betaflight 3.2.0 here.

    $18.99-$72.99 1

    SKU:BFESC3

    Weight: 0.10 kg

  • Favourite Littlebee Summer 2-6s BLHeli_32 30A Dshot1200 ESC

    Following the 35A, FVT just released its new 30A version of Littlebee Summer ESC. This new 30A comes with 2-6s input. The burst current can be up to 35A / 10s. It has current sensor, while the 35A version does not.Feature: 1:input Voltage:2-6S Lipo 2:NO BEC 3:Continue Current:30A,Burst Current:35A up to 10S 4:Size: 31*17mm. 5:Weight:8g(include Power and signal wire) 6:Support Oneshot125,Oneshot42,Mutishot and at least Dshot1200 etc. 7:Main IC:runs on an ARM 32bit MCU(STM32F051),running at 48MHz 8:MOS:Both low and high side fets are Nfets,szie is 5*6,easy to heat 9:programmable pwm frequency, up to 48kHz,run motors even smoother 10:Low voltage ,temperature and current protection 11:New telemetry function 12:BLHeli-32 Bootloader & Firmware

    $17.99 $13.49, Save 25% OFF

    SKU:FVT30A

    Weight: 0.10 kg

  • Wraith32 MINI- 32bit BLHELI_32 ESC

    Specifications:2-6s LIPO input25A designed10*20mmBLHeli_32 is the third generation BLHeli code, following base BLHeli and BLHeli_S.BLHeli_32 runs on an ARM 32bit MCU, initially it will be on a Cortex-M0 running at 48MHz, but there are MCUs out there that can run a lot faster.So what can the increased MCU speed do?First of all, it can run input signals with lower latency at faster rates. Dshot up to at least Dshot1200, and at rates up to at least 32kHz is now supported.Secondly it allows packing of more functionality. - Like programmable pwm frequency, up to 48kHz, that can run motors even smoother, and also allows for moving of small but potentially disturbing humps in the throttle response. All ESCs have these bumps, with BLHeli_32 they can now be moved in the rpm range, to a place where the system has low sensitivity to them.- Like auto timing. Which is not the option to choose if you’re after max power. But if you want the most efficient running with very good robustness against desync, it is the perfect choice.- Like voltage and current limiting. Which is implemented in the code, and will be supported on some ESCs. Voltage limiting is desirable for fixed wing crafts. And current limiting adds protection against ESC failure.- Like programmable brake on stop force. Which allows control of the braking of fixed wing props.- Like improved direction change in bidirectional mode.- Like more to come in the future. Such as setup from the FC by using Dshot commands. Such as telemetry functionality. There is room to grow performance and functionality.Some Tips:BLHeli_32 ESC Firmware OverviewWhat is Dshot1200 and Why Dshot1200 is Better?How to Get Dshot1200 Running in Betaflight?Downloads:Download the latest BLHeli_32 Configurator here.Download the BLHeli_32 User Manual here.Download Betaflight 3.2.0 here

    $14.99 1

    SKU:WMN32

    Weight: 0.10 kg

  • X-Racer Quadrant 2-6S 35A 32Bit BLHeli_32 ESC Dshot1200

    Features of New X-Racer Quadrant 35A 2-6S 32Bit BLHeli_32 ESC:Uses the latest BLHeli_32 firmware. Dshot up to at least Dshot1200.At rates up to at least 32kHz is supported.Four tiny ESCs can be installed separately on the arms, or installed together like a PCB under the flight controller.2-6s Lipo input.Rated at 35A current with a max of 50 amps of current load (Less than 10s).Small in size: 20 x 24mm3 grams each piece and about 12 grams for a set of 4 pieces.Compatible to BetaflightF3 Flight ControllerThe new X-Racer Quadrant BLHeli_32 ESC has followed the design of previous 4-in-1 design of X-Racer Quadrant. It is not a single board, but four tiny ESCs can be installed separately on the arms, or installed together like a PCB under the flight controller. This is the 35A version, there is also another 25A version available for your choice.The new X-Racer Quadrant 35A is flashed with the latest BLHeli_32 program. Dshot up to at least Dshot1200, and at rates up to at least 32kHz is now supported. BLHeli_32 is the 3rd generation of BLHeli firmware after BLHeli and BLHeli_S. BLHeli_32 runs on an ARM 32bit MCU, initially it will be on a Cortex-M0 running at 48MHz, but there are MCUs out there that can run a lot faster. The way “pass-through” works is quite similar to previous versions such as BLHeli_S. Basically it uses the flight controller as a programming tool or adapter to allow the computer to talk to the ESC’s directly, so you can change settings or flash new firmware etc.So what can the increased MCU speed do?First of all, it can run input signals with lower latency at faster rates. Dshot up to at least Dshot1200, and at rates up to at least 32kHz is now supported.Secondly it allows packing of more functionality. - Like programmable pwm frequency, up to 48kHz, that can run motors even smoother, and also allows for moving of small but potentially disturbing humps in the throttle response. All ESCs have these bumps, with BLHeli_32 they can now be moved in the rpm range, to a place where the system has low sensitivity to them.- Like auto timing. Which is not the option to choose if you’re after max power. But if you want the most efficient running with very good robustness against desync, it is the perfect choice.- Like voltage and current limiting. Which is implemented in the code, and will be supported on some ESCs. Voltage limiting is desirable for fixed wing crafts. And current limiting adds protection against ESC failure.- Like programmable brake on stop force. Which allows control of the braking of fixed wing props.- Like improved direction change in bidirectional mode.- Like more to come in the future. Such as setup from the FC by using Dshot commands. Such as telemetry functionality. There is room to grow performance and functionality.Software SetupYou will need to flash Betaflight V3.2 or newer firmware on your FC, you can download it from: https://github.com/betaflight/betaflight/releases/tag/v3.2.0.Load the firmware target for your FC locally, and flash (shouldn’t need to short bootloader pins)Download latest BLHeliSuite for BLHeli_32: http://www.blheli32.com/download/Some Tips:BLHeli_32 ESC Firmware OverviewWhat is Dshot1200 and Why Dshot1200 is Better?How to Get Dshot1200 Running in Betaflight?DownloadsDownload the latest BLHeli_32 Configurator here.Download the BLHeli_32 User Manual here.Download Betaflight 3.2.0 herePack for one piece.Pack for a set of 4 pieces.

    $18.99-$74.98

    SKU:XQ35B32

    Weight: 0.10 kg

  • X-Racer Quadrant 2-6S 25A 32Bit BLHeli_32 ESC Dshot1200

    Features of New X-Racer Quadrant 25A 2-6S 32Bit BLHeli_32 ESC:Uses the latest BLHeli_32 firmware. Dshot up to at least Dshot1200.At rates up to at least 32kHz is supported.Four tiny ESCs can be installed separately on the arms, or installed together like a PCB under the flight controller.2-6s Lipo input.With 25AMp constant RMS, 30A max.Less than 3 grams each piece and about 11.5 grams for a set of 4 pieces.Small in size: 18 x 24mmCompatible to BetaflightF3 Flight ControllerThe new X-Racer Quadrant BLHeli_32 ESC has followed the design of previous 4-in-1 design of X-Racer Quadrant. It is not a single board, but four tiny ESCs can be installed separetely on the arms, or installed together like a PCB under the flight controller. This is the 25A version, there is also another 35A version available for your choice.The new X-Racer Quadrant 25A is flashed with the latest BLHeli_32 program. Dshot up to at least Dshot1200, and at rates up to at least 32kHz is now supported.BLHeli_32 is the 3rd generation of BLHeli firmware after BLHeli and BLHeli_S. BLHeli_32 runs on an ARM 32bit MCU, initially it will be on a Cortex-M0 running at 48MHz, but there are MCUs out there that can run a lot faster.So what can the increased MCU speed do?First of all, it can run input signals with lower latency at faster rates. Dshot up to at least Dshot1200, and at rates up to at least 32kHz is now supported.Secondly it allows packing of more functionality. - Like programmable pwm frequency, up to 48kHz, that can run motors even smoother, and also allows for moving of small but potentially disturbing humps in the throttle response. All ESCs have these bumps, with BLHeli_32 they can now be moved in the rpm range, to a place where the system has low sensitivity to them.- Like auto timing. Which is not the option to choose if you’re after max power. But if you want the most efficient running with very good robustness against desync, it is the perfect choice.- Like voltage and current limiting. Which is implemented in the code, and will be supported on some ESCs. Voltage limiting is desirable for fixed wing crafts. And current limiting adds protection against ESC failure.- Like programmable brake on stop force. Which allows control of the braking of fixed wing props.- Like improved direction change in bidirectional mode.- Like more to come in the future. Such as setup from the FC by using Dshot commands. Such as telemetry functionality. There is room to grow performance and functionality.Some Tips:BLHeli_32 ESC Firmware OverviewWhat is Dshot1200 and Why Dshot1200 is Better?How to Get Dshot1200 Running in Betaflight?Downloads:Download the latest BLHeli_32 Configurator here.Download the BLHeli_32 User Manual here.Download Betaflight 3.2.0 here.

    $17.99 $14.93, Save 17% OFF 1

    SKU:XQ25B32

    Weight: 0.10 kg

  • Wraith32 Plus - 32bit 50A BLHeli_32 ESC DSHOT1200

    Features:-Build in Current sensor-On-Board RGB LED-2-6s LIPO input-50A designed-20*35mmWraith32 Plus is a 50A 32bit BLHELI ESC with newest BLHeli_32 firmware. It is a 6S powerhouse that supports voltage limiting and current limiting as well as a bright RGB LED.BLHeli_32 is the 3rd generation of BLHeli firmware after BLHeli and BLHeli_S. BLHeli_32 runs on an ARM 32bit MCU, initially it will be on a Cortex-M0 running at 48MHz, but there are MCUs out there that can run a lot faster. Now the first ESC that supports BLHeli_32 has already been announced – the Wraith32 and Wraith32 Plus. Luckily, FPV Model will receive these as soon as they make them out, and all our customers will have the chance to be the first in the world receive these new BLHeli_32 ESCs.So what can the increased MCU speed do?First of all, it can run input signals with lower latency at faster rates. Dshot up to at least Dshot1200, and at rates up to at least 32kHz is now supported.Secondly it allows packing of more functionality. - Like programmable pwm frequency, up to 48kHz, that can run motors even smoother, and also allows for moving of small but potentially disturbing humps in the throttle response. All ESCs have these bumps, with BLHeli_32 they can now be moved in the rpm range, to a place where the system has low sensitivity to them.- Like auto timing. Which is not the option to choose if you’re after max power. But if you want the most efficient running with very good robustness against desync, it is the perfect choice.- Like voltage and current limiting. Which is implemented in the code, and will be supported on some ESCs. Voltage limiting is desirable for fixed wing crafts. And current limiting adds protection against ESC failure.- Like programmable brake on stop force. Which allows control of the braking of fixed wing props.- Like improved direction change in bidirectional mode.- Like more to come in the future. Such as setup from the FC by using Dshot commands. Such as telemetry functionality. There is room to grow performance and functionality.Some Tips:BLHeli_32 ESC Firmware OverviewWhat is Dshot1200 and Why Dshot1200 is Better?How to Get Dshot1200 Running in Betaflight?Downloads:Download the latest BLHeli_32 Configurator here.Download the BLHeli_32 User Manual here.Download Betaflight 3.2.0 here.

    $24.99-$99.00

    SKU:W32EP

    Weight: 0.10 kg

  • Wraith32 - 32bit 35A BLHeli_32 ESC DSHOT1200

    *** These are the final upgradable version of Wraith32 BLHeli_32 ESCs. Please rest assured to buy and use. *** Friendly Reminder: If you are using high KV motors, please add a line of soldering along the ESC sides for a better protection and to give more power.Wraith32 is the first 32bit BLHELI ESC that use the latest BLheli_32 firmware in the world. Dshot up to at least Dshot1200, and at rates up to at least 32kHz is now supported. If you are seeking for a small, powerful blheli_32 capable 32bit ESCs, the Wraith32 ESCs will certainly fit the bill providing 35Amps of power.The Wraith32 ESC runs in conjunction with an ARM 32bit compatible MCU. It can run input signals with lower latency, at faster rates, smooths out the RPM band, is capable of both voltage and current monitoring and limiting, as well as offering customization of the brake on stop force. Unlike current ESCs, the Wraith32 ESC has A LOT of room to grow and wide compatibility range with future products. One of the nicest features with the Wraith32 35A ESC is the auto timing feature, which (essentially) is designed to offer the pilot the smoothest and most efficient flight experience available, which is a freestyle pilots dream come true! Features:32bit Compatible ESC (Blheli_32)Dshot1200 up to 32kHzIncredibly small sizeVery low weightAuto Timing FeatureOn-Board RGB LEDBuild in Current sensorSmooth ResponseCompatible to BetaflightF3 Flight ControllerSpecifications:2-6s Lipo input35A designedCompatible to BetaflightF3 Flight ControllerSize: 15*30mmPackaging: One ESC each PP bag with Wraith32 lable.BLHeli_32 is the 3rd generation of BLHeli firmware after BLHeli and BLHeli_S. BLHeli_32 runs on an ARM 32bit MCU, initially it will be on a Cortex-M0 running at 48MHz, but there are MCUs out there that can run a lot faster.Now the first ESC that supports BLHeli_32 has already been announced – the Wraith32 and Wraith32 Plus. Luckily, FPV Model received these from the manufacturer Airbot as soon as they made them out, and all our customers have the chance to be the first in the world receive these new BLHeli_32 ESCs.Wraith32 Plus is a 6S powerhouse that supports voltage limiting and current limiting as well as a bright RGB LED.Wraith32 is a smaller 6S version that also supports voltage limiting and current limiting as well as a bright RGB LED.So what can the increased MCU speed do?First of all, it can run input signals with lower latency at faster rates. Dshot up to at least Dshot1200, and at rates up to at least 32kHz is now supported.Secondly it allows packing of more functionality. - Like programmable pwm frequency, up to 48kHz, that can run motors even smoother, and also allows for moving of small but potentially disturbing humps in the throttle response. All ESCs have these bumps, with BLHeli_32 they can now be moved in the rpm range, to a place where the system has low sensitivity to them.- Like auto timing. Which is not the option to choose if you’re after max power. But if you want the most efficient running with very good robustness against desync, it is the perfect choice.- Like voltage and current limiting. Which is implemented in the code, and will be supported on some ESCs. Voltage limiting is desirable for fixed wing crafts. And current limiting adds protection against ESC failure.- Like programmable brake on stop force. Which allows control of the braking of fixed wing props.- Like improved direction change in bidirectional mode.- Like more to come in the future. Such as setup from the FC by using Dshot commands. Such as telemetry functionality. There is room to grow performance and functionality.Some Tips:BLHeli_32 ESC Firmware OverviewWhat is Dshot1200 and Why Dshot1200 is Better?How to Get Dshot1200 Running in Betaflight?Downloads:Download the latest BLHeli_32 Configurator here.Download the BLHeli_32 User Manual here.Download Betaflight 3.2.0.Before Purchasing: The products come with different batches may have different silk printing on them.

    $16.99 $14.95, Save 12% OFF

    SKU:W32E

    Weight: 0.10 kg




Find us on Google+ Watch us on Youtube Like us on Twitter Follow us on Facebook

Home   |   About Us   |   New Products   |   Multi-Rotors   |   FPV Airplanes   |   FPV Equipment   |   Battery / Chargers   |   Tools & Accessories   |   Contact Us   |   Blog   |  Site Map

Product Tags: ABCDEFGHIJKLMNOPQRSTUVWXYZ0-9

Copyright © 2015 FPVMODEL.COM®. All Rights Reserved.