Sorted:
  • DYS ARIA 35A 3-6S Blheli_32 Dshot1200 ESC

    It is always better late than never. Finally the DYS Aria 35A BLHeli_32 ESC is officially launched. If you are still running its XM30A, this could be a very good upgrade for the BLHeli_32 goodness.DYS ARIA 35A 3-6S Blheli32 Dshot1200 ESCSpecifications:Current Rating: 35A (40A burst)Voltage Rating: 3S to 6SDimension: 32mm x 16mm x 5mmWeight: 4.73g bare PCB, 8.1g with wiresCurrent sensing and limitingBuilt-in Programmable RGB LEDPrice: $15.99 eachSupports DShot1200 and older ESC protocolsFeatures:With 32bit ARM Cortex MCU STM32F051 48MHZ micro processor, throttle 2048 resolution ratio, strong anti-interference capacity.Built-in sensor can be reaction of temperature, output power, output current etc, also programmable for protection.Support Blheli_32 firmware, can use the signal wire to upgrade the firmware or change the configuration on line.Current Meter to help show current indication of OSDWith USB linker can be programmable throttle setting like support positive and negative, two way mode, FPV 3D mode, motor speed, braking, PWM frequency, inlet angle speed setting, onboard RGB LED for customize color, Beep etc.It use the self-adaption control system,can go automatic with the all kind of the motor in the market,at the mean time it support up to 500HZ PWM, oneshot 125, oneshot 42, Multishot and Dshot 150/300/600/1200.With special optimize in multi-axis, the motor can launch smoother in a good throttle curve, fast response,great power, and highly support the multi-axis,fixed-wing and helicopter.The twisted-pair signal wire can lower the crosstalk inside cooper wire when it transfer,which will make the flight more stable.MCU hardware,Driver circuit, Mosfet will come with double voltage protection.To adopt the new process MOSFET of low internal resistance, will help increase resistance to flow. Also, the professional MOS driver chip makes the best efficiency.Mosfet is covered with aluminum sheet for cooling,which can bring more efficiency and stability.With special process of 6 layer thicken PCB will lower resistance, small calorific value and bigger impact resistance current.Nice optimize layout of the components and parts makes a smaller size, lighter weight and easy to build.

    $15.99 $13.59, Save 15% OFF

    Time left: 0s

    SKU:DA35A

    Weight: 0.10 kg

  • BrotherHobby Tornado T2 2206 2600kv Brushless Motor for FPV Multicopters

    Brotherhobby has created these 2206 T2 series of motors with a unique design. The bell design has a new look, the body is made of solid 7075 aluminum, and the motor itself features 1.75mm thick N52H arc magnets. All while only weighing about 31g. With these magnets you dont need to sacrifice structural integrity for low weight, you can have both.  Great response time and power.SpecificationsConfiguration:12N14PNo.of Cells(Lipo): 3-5SRotor: 1.75mm N52H arc magnetsWire AWG: 20AWGWiring config Single-stranded: 1 x 0.55mm Delta DLRKStator: 0.15mm Nippon Steel silicon steelBearings: Japanese NSKBase casing: Al 7075Bell cap: Al 7075Weight: 30.8G

    $23.99 $15.59, Save 35% OFF

    Time left: 0s

    SKU:T2-2206

    Weight: 0.10 kg

  • AOMWAY Commander 3D 40CH 5.8G FPV Goggles

    A new player on the goggle market, the Aomway Commanders V1 3D FPV goggles are a snug fit, the feedback so far on the optics has been great and it has several unique features that make them stand out. Switchable 4:3 and 16:9 aspect ratio, "black-box" style DVR recording (it starts recording as you turn on the goggles) are some of the simple yet cool things about these goggles. The integrated fan on the bottom of the goggles is also a nice touch.Main Features:- 2 x 16:9 854 x 480px WVGA display with 32-degree FOV - Two built-in 5.8G 40CH highly sensitive receivers- With HDMI connector, supports 720P- Supports 3D / 2D image, adjustment of IPD ( 59 - 69mm ) - DVR function, NTSC / PAL / Auto- Supports headtracker ( not included ) and installation of optical lenses ( not included )- Anti-fog fan, comfortable eye maskDisplay : Resolution : 854*480(WVGA)LCD, LED backlightRatio : 16:9,4:3FOV : 32°,glass opticalIPD : 59-69mm(adjustable) Support 3D, HDMI,DVR,Headtracker:3D Display : Video 3D;HDMI 3DAudio Output : stereo Format : NTSC/PAL AutoHDMIin : 720PDigital Video Record : Integrated simulation DVR(can record RF and AVIN siginal) , Support 32Gb micro TF cardVideo Compression Format : MJPG 30fps Headtracker : modularization (not included) Adjustable : Lightness/Contrast/Channel/Display Mode/Digital Record/Head Tracker Switch 5.8G 40CH Diversity ReceiverWith build in 2 40CH high sensitive receiver, auto search Interface : Headphone : 3.5mm 3 headphone jackAVIN Interface : 3.5mm 4 audio-video interface Headtracker Interface : PS2 terminalTF Card : Micro TF CardDCIN : Standard 5.5*2.1

    $345.99 $294.09, Save 15% OFF

    Time left: 0s

    SKU:AWC3D

    Weight: 0.90 kg

  • FrSky M-9 Hall Sensor Gimbal For Taranis X9D & X9D Plus

    Upgrade your Taranis X9D with this plug-n-play high resolution M9 Gimbal from FrSky. The highly sensitive Hall sensors will not wear out quickly. It has an extremely smooth feel with the quad ball-bearings and the metal outer construction. Thicker 4mm stick ends give you a solid link to your controls. Fully adjustable tension and easily disable the self centering axis with one screw. This is a must have accessory for achieving those precision flight maneuvers. Spcification:Brand Name: FrskyModel: M9-GimbalItem Name: M9-Gimbal M9 Sensitivity Sensor GimbalSupply Voltage (VCC): DC 3.0 ~ ±0.5V Sensitivity: 2.50 mV/G Linear Output Voltage Range: 0.1 ~ (VCC +0.1) V Quiescent Output (TA = 25°C, B = 0 G): 0.5 × VCC Noise (no load): ≤40mVppFeatures: -Hall sensor-4 ball-bearings-Adjustable tension-Can be enable or disable self centering on both axis and ratcheting on the Y axis-Special material quality that wears well

    $24.99 $19.99, Save 20% OFF

    Time left: 0s

    SKU:FSM9G

    Weight: 0.15 kg

  • DYS XSD 30A 3-5S ESC BLheli_S & Dshot600/Dshot300 Latest Version

    Lets Have Fun with DYS XSD30A V2This is the latest version of XSD30A ESC that just been released by DYS. Dshot300 & Dshot600 compatible. Much smoother and more powerful. It uses better capacitor & MOS tube to reduce the resistance and gain 20% more power comparing to the V1.Description:Item Name: XSD30A Solder VersionInput voltage: 3-5S LipoBEC: NOType: BLheli_S Firmware & DShot600/ DShot300Weight: 7.2gSize: 30*15*6mmFeature: Silabs EFM8BB21Feature: BLHeli_S does Damped Light onlyFirmware upgradable via signal wire (works with USB Linker for XM series)Supports Motors with super high KV (EFM8BusyBee 50MHz can handle up to 500k eRPM)Supports DShot600, DShot300High-current burst ratingHigh-Resolution Throttle steps

    $16.99 $13.93, Save 18% OFF

    Time left: 0s

    SKU:XSD30A

    Weight: 0.10 kg

  • 6x15mm Coreless Motor for Blade Inductrix and Blade Nano QX (Speed: Fast)

    These are powerful motors that works great in the Blade Inductrix, Blade Nano QX, Blade CPX/S. These motors come with plug and 6cm wire, they are better suited to FPV and will be the perfect upgrade for your Tiny conversion. If you are looking for punch and durability, you found it. Warning: These motors are too power hungry for the stock packs! You need strong batteries to run these motors at full performance. Suggest use 205mah mylipo pack, and they will deliver a lot of punch and maximum runtime.Warning: Applies only to the original Nano QX, without FPV. These motors will turn your Nano QX into an insane jaw-dropping pocket rocket, but it will not like hovering! Depending on the battery you use, you will see varying degrees of oscillations (wobble) during hover and slow flight in SAFE mode. Agility mode does not have this problem.Specifications:Speed: 14.000KvOperating voltage: 1.5-3.7VMax. thrust: 15g (direct drive)1.0A load current at 3.7V (direct drive)Lifetime rating: 5-6 hoursPlug: Micro-JST-1.25Clockwise: red +, blue -Counter clockwise: white +, black -Warning: To maximize performance and life span, please do not run them in reverse! Wire colors are reversed.Dimensions:Motor diameter: 6mmMotor length: 15mmShaft Diameter: 0.8mmShaft Length: 4mmWeight: 1.8g Wire length: 60mmPlease note: wire color coding is reversed from the stock motors. Blade has decided to code their motors differently to everyone else in the industry. If you take off, and your Inductrix or Nano QX spins in circles and yaws like a micro frisbee on steriods, please note wire colors are reversed. Your motors are installed in the wrong spots.

    $2.19 $0.99, Save 55% OFF

    Time left: 0s

    SKU:CL14M

    Weight: 0.10 kg

  • Dragonfly Booster 5.8G 3dBi TX/RX FPV Antenna RP-SMA/SMA

    Better signal quality and much more durable. These Dragonfly Booster antennas can be survived from the hardest crashes with the specially designed cover and silver connector. Three different sizes?(5cm, 8cm and 11cm) in SMA and RP-SMA?are selectable to meet your special needs for the build.Specification:Frequency Range: 5400 ~ 5900MhzImpedance: 50ΩV.S.W.R: ≦1.5Gain: 3 ~ 3.5dBiFirst Upper Sidelobe Suppression (dB) ≥15Front to Rear Ratio (dB) ≥25Cross-polarization Discrimination (dB) ≥15Port Isolation (dB) ≥28Polarization: Vertical/HorizontalMaximum Input Power: 10WCable: RG141Color: BlackConnector: RP-SMA / SMA (Optional)Length: 5cm / 8cm / 11cm (Optional)Weight: 10g / 11g / 13g Package Included:?1 x Antenna* 5.8G Vertical Polarization* 5.8G Horizontal Polarization

    $15.99 $9.91, Save 38% OFF

    Time left: 0s

    SKU:FBSA

    Weight: 0.10 kg

  • KL200Race Racing Quadcopter with PCB Board

    KL200RACE Brief Introduction & Flying FootagesUpdated on 01/09/2017: Added the plastic motor screw bumpers and battery protection plate to the frame kit. The same price, but better protection to motors and battery. Also, the 3D printed LED bar now comes with a slot for a better placing of LED inside. Introducing the FPVMODEL KL200RACE FPV racing quadcopter. It is a symmetric 200mm size airframe. The 200mm is measured motor shaft to motor shaft diagonally. This airframe is designed by FPVModel team pilot Ka Kei Leung and already a proven winner on the race track, with Ka Kei won multiple racing events while using this quad.The KL200RACE is built for FPV racing. It features a light-weight, symmetrical carbon fiber body. The frame has been stripped down to the bare essentials yet maintain the strength and durability. The weight is only 82 grams including the PDB and included hardwares.Two ways to place the LiPo battery. You can fly with your HD camera with the 3D printed GoPro mount, and strap the battery under the bottom plate. Or you can place the battery on the top plate if you are using the FPV camera, like HS1190. The angle of FPV camera mounting can be adjusted from 0 degree to 60 degree as per your desire. The KL200RACE frame also comes with a small LED strip to set at the back. With only one LED, your airframe will be shinning and stand out other racing quadcopters. The colors of LED can be set via Cleanflight.The KL200RACE is not with a "X" type layout but a butterfly like shape to avoid the PID setting problem of usual X frames. It utilizes high quality 3K carbon fiber that is precision machined for a superb fit-and-finish. This Carbon Fiber is backed by FPVmodels name so you can trust that it is top of the line.For your easy build, we have several KL200RACE ARF packages available.Specs & Features4.0mm Main Frame2.0mm Top Frame / 4.0mm Top Frame (Need to purchase seperately)Aluminum Anodized & Stainless Steel HardwareLight Shell with SMA Holder ComboGoPro Mount93 Grams only (Including Frame, PDB and Hardwares) Friendly reminder: The battery showed in the pictures is not included in the frame kit.The parts included in the frame kits. KL200Race is designed by FPVModel team pilot Kakei Leung and named after him. It has already a proven winner on the race track, with Kakei won multiple racing events while flying with this quad.

    $59.99 $32.99, Save 45% OFF

    Time left: 0s

    SKU:KL200P

    Weight: 0.45 kg

  • FPVMODEL Leather Velcro Battery Strap 200mm x 14mm (4pcs)

    FPVMODEL Leather Velcro Battery Strap 200mm x 14mm (4pcs)Specifications:Name: FPVMODEL Velcro Battery StrapSku#: 4MLVSSize: 200mm x 14mmColor: Black Quantity:4 pcs/kit

    $5.39 $1.99, Save 63% OFF

    Time left: 0s

    SKU:4MLVS

    Weight: 0.10 kg

  • FX797T Micro FPV Camera & 5.8GHz 40CH 25mW VTX

    Time to get your micro builds going! The FX797T Micro FPV Camera & 5.8GHz 40CH 25mW VTX is extremely small and could be installed on almost anything, most multi-rotors wouldn’t even notice it was there.  This camera / VTX combo is the perfect FPV plug & play solution for micro setups.Due to their size and adaptability, the FX797T micro camera and video transmitter has taken the FPV world by storm. This fabulous little piece of tech allows the user to install on the smallest of builds and get reception up to 100 meters in range. The design of this camera/vtx is intended to be small enough to mount on almost any micro flyer out there and it has found it’s home in the Tiny Whoop/Blade Inductrix quad to be it’s calling. Featuring the full range of 40 Channels this camera outputs all common video signals including the latest “race band” channels. Combined with it’s low amp draw this camera is perfect for those tiny builds that are already using the smallest of batteries. Easy to install and easy to wire up (just gnd and power lines) this camera will simplify your build. Description:Item Name: FX797T Micro FPV Camera & 5.8GHz 40CH 25mW VTX FX797 Output power: 25mWInput power: 2.5–5V Current Consumption: 230mAAV Output: VGA 640x480 PAL/1VP-PCamera resolution: 600TVLMin illumination: 1 luxField of view: 120° viewing angleAntenna dimensions: 20mm X 25mm diameterAntenna: 3 lobe right hand circular polarizedVideo output: NTSCFrequency: 5.8GHz 5 bands 40 channels, with Raceband: 5658-5917MHzBands: see below channel table.Push button operation, long press for band, short press for channelSpecs:2 Row LED indicators, 5 LED for band, 8 LED for channelSize: 17x17.5x12.5mmWeight: 3.4gFeatures:Micro Size and Light weightEasy installation for racing droneFive bands 40 channels with RacebandButton Control Instead Of SwitchIncluded:1 x FX797T 5.8G 25mW Transmitter With 600TVL Camera and Antenna1 x manual

    $41.99 $19.74, Save 53% OFF

    Time left: 0s

    SKU:FX797T

    Weight: 0.10 kg

  • MC1806 2300KV Titanium Brushless Motor

    The MC1806 2300kv  multirotor motor is ideal for small to medium sized multirotors, including ZMR180 and ZMR250 V2. It comes with all necessary components to get you up and running.Please note that this motor is directly sourced from the factory that without any logo, but quality guaranteed.  Factory Specifications:KV: 2300Configuration: 12N14PStator Diameter: 18mmStator Length: 6mmMotor Dimensions (Dia.*Len): Φ23×15.5mmWeight: 20gInternal Resistance:53mΩTechnical Data:

    $12.99 $3.90, Save 70% OFF

    Time left: 0s

    SKU:MC1806W

    Weight: 0.20 kg

  • ZMR250 V2 PDB

    Special sale on the spare arms for ZMR250 V2, suitable for 1806 motors, buy them CLICK HERE >>>?Known as the ZMR250, C250, QAV250, H250, Blackout Clone or the Mystery 250, whatever the real name is, ZMR250 carbon fiber frame is probally one of the most popular mini quad frames in this hobby.We have taken the advise of many and reworked the ZMR250 V2 PDB. It now features ESC pads on the top and bottom of the board. Traces and main power distribution have been routed in a manner to avoid running under the arms. Optional 12V regulator w/ built in LC filter is now available.

    $32.99 $7.92, Save 76% OFF

    Time left: 0s

    SKU:250V2PDB

    Weight: 0.10 kg




Find us on Google+ Watch us on Youtube Like us on Twitter Follow us on Facebook

Home   |   About Us   |   New Products   |   Multi-Rotors   |   FPV Airplanes   |   FPV Equipment   |   Battery / Chargers   |   Tools & Accessories   |   Contact Us   |   Blog   |  Site Map

Product Tags: ABCDEFGHIJKLMNOPQRSTUVWXYZ0-9

Copyright © 2015 FPVMODEL.COM®. All Rights Reserved.