Sorted:
  • *Pre-order* BetaflightF4 Flight Controller

    BetaflightF4 How to ESC Telemetry, Smart Port Audio, Smart Port TelemetryExpected shipping date: Oct 25th, 2017. BetaflightF4 is the follow up design to the very popular BetaflightF3. Following in the same path as Betaflight F3 we have kept a very similar footprint in terms of design with a few added modifications. The F405 has replaced the F303 to allow for lower CPU loads.We have eliminated the 5v/3.3v jumper and added two seperate connection points, one for sbus and one for spektrum users. The jumper still remains for the battery voltage/5v connection for connecting your camera. While wiring the board it is recommended to get power for your vtx either from a different 5v source on the board or if using a higher voltage vtx power it from the battery input coming into the pdb. Running ground loop at Agnd with gnd wires from camera and vtx is still recommended to give the cleanest video signal. Another small design change to this board was changing the BEC, this change takes the recommended 5v 2A current limit and drops it down to 5V 1.5A, its a small change but one that we opted for in order to use a more reliable BEC.BetaflightF4 now comes with telemtry pads for BLHeli32 ESCs these pads are located between the signal and gnd pads for the ESC connections.FeaturesIntegrated PDBBuilt in OSD customizable via Betaflight OSDCurrent sensorIntuitive layoutFlash memory for blackboxTailored to support BetaflightWhen running 8K/8K, CPU usage remains low Download Latest Firmware: Betaflight 3.2.0SpecificationsF405 ProcessorMPU6000 Gyro/ACC SensorBEC Max current 5V 1.5ABuilt in OSD – configurable via Betaflight GUICurrent sensorPower distribution board with six-layer PCBOSD Max Current: 145AWiring Diagram - Click to enlarge!

    $44.99 3

    SKU:BFF4

    Weight: 0.10 kg

  • *Pre-order* Betaflight Hive Backpack

    * We are now taking pre-orders on Betaflight "Hive" Backpacks to judge the demand.  During this time we are selling the backpack at a discounted rate of $169.99 USD, while the estimated final selling price is around $189.99 - $199.99 USD. * Estimated shipping date: November 12th, 2017. * Before Purchasing: Due to the size limit, we offer free shipping on the backpack by EMS only. We have been going over the design of the Betaflight Backpack for several months now and have finally settled on the final prototype. While we were designing the Betaflight backpack one thing kept coming up in the design aspect was how much room the transmitter took up inside the bag. So, we thought the best design would be to make a hard shell top mounted case on the top of the bag. The hard shell top of the case allows for extra protection of your transmitter and frees up valuable space inside the bag. The interior of the bag is very similar to other DSLR style camera bags and allows for multiple design layouts by using cushioned dividers that velcro in place and let each user layout their own custom setup based on their specific needs. The exterior of the bag has multiple strap points that are adjustable in height separation by plastic strap connectors the move up and down on a rail seam at the outside edges of the hard shell cover that allow for multiple quads to be strapped to the bag, freeing even more space for tools and accessories on the interior of the Betaflight Backpack, but there is also room on the inside if you prefer to carry your quads in the bag. The overall design of this backpack is geared towards those that are serious fliers and have multiple quads and many tools and accessories that they carry with them while traveling by air or even just to the local field. Features:International carry-on size compatibility for air travel. Dedicated lap-top pocketElastic daisy chain tool panel for your hex drivers and other hand held tools. Large interior pocket for carrying props with hard shell cover on the bag for added protection from outside forces. 1680D ballistic nylon bag material for long life durability. Featuring the best zippers in the market made by YKK to ensure long lasting zipper life. Contoured adjustable padded harness with height adjustable chest strap. Rain cover that pulls out from bottom panel pocket for fast rain protection.Exterior Dimensions:  56 x 34 x 18cm*Description and photos are in the early stages. These will be updated as progress moves forward with the manufaturing process.  Betaflight HIVE is a comfortable and protective FPV quad racing backpack built to carry and protect your FPV racing drones and accessories.Large interior pocket for carrying props with hard shell cover on the bag for added protection from outside forces.Interior and Exterior FPV Quad mounting locations.While we were designing the Betaflight backpack one thing kept coming up in the design aspect was how much room the transmitter took up inside the bag. So, we thought the best design would be to make a hard shell top mounted case on the top of the bag. The hard shell top of the case allows for extra protection of your transmitter and frees up valuable space inside the bag. The interior of the bag is very similar to other DSLR style camera bags and allows for multiple design layouts by using cushioned dividers that velcro in place and let each user layout their own custom setup based on their specific needs. Plenty room to store your FPV accessories, you are able to carry up to 30 1500mAh batteries!!!Dedicated laptop pocketComes with a GoPro mount, recording every wonderful moment has never been so easy.  (GoPro camera not included)**** Friendly reminder: Price for Betaflight HIVE backpack only. Above pictures for demonstration purpose that the quads, tools, GoPro and other accessories are not included.

    $199.99 $169.99, Save 15% OFF    4

    SKU:BFBP

    Weight: 3.50 kg

  • Betaflight 32Bit 35A 2-6S BLHeli_32 ESC Dshot1200

    *** Update on Sept 12th, 2017: This is the new updated version of Betaflight BLHeli_32 ESC that comes with a line of soldering along the ESC sides for a better protection and giving more power. We are at it again and the guys at Betaflight, FPV Model, BLHeli, and Airbot have come together to create a version of BLHeli_32 ESCs that FPV Model hopes will not disappoint. Introducing a fresh take on an ongoing development with BLHeli_32 we are introducing BetaBees, BlHeli_32 ESCs designed in conjunction with Airbot.BLHeli_32 is the third generation BLHeli code, following base BLHeli and BLHeli_S. It runs on an ARM 32bit MCU, initially it will be on a Cortex-M0 running at 48MHz, but there are MCUs out there that can run a lot faster.  BLheli_32 can run input signals with lower latency at faster rates. Dshot up to at least Dshot1200, and at rates up to at least 32kHz is now supported.Here is what BLHELI_32 has to say about their new "Power to perform":Programmable PWM frequency of up to 48KHzAuto-timing for higher efficiency and reliabilityVoltage/Current limitingAdjustable “Brake on Stop” forceImprove direction change in Bidirectional modeESC TelemetryConfiguring from FC using DShot commandsFeatures: Built in Current SensorExtra capacitors to help smooth noisy envrionments.Customizable color choice RGB LED using Blheli_32 software.Large positive and ground pads for easy soldering. 2-6s Lipo input35A continuous current  (can handle burst above 45A but please be reasonable, do not overwork  your motors)TX pad on ESC used for Telemetry pad. (connect to FC and you would get current sensing, motor RPM, ESC temperature etc)Specifications :Input: 2-6s LiPolyConstant: 35 AmpsBurst: 45 AmpsBEC: No BEC, OPTO onlyDimensions: 34x16x7mmWeight: 6g (without motor wires)Includes:1 x Betaflight BLHeli_32 35A ESC1 x 16AWG Red Silicon Wire 10cm1 x 16AWG Black Silicon Wire 10cm3 x 20AWG Black Silicon Wire 10cm1 x 26AWG Red Silicon Wire 10cmSome Tips:BLHeli_32 ESC Firmware OverviewHow to Connect BLHeli_32 ESC to Congigurator BLHelisuite32 via FC PassthroughWhat is Dshot1200 and Why Dshot1200 is Better?How to Get Dshot1200 Running in Betaflight?Downloads:Download the latest BLHeli_32 Configurator here.Download the BLHeli_32 User Manual here.Download Betaflight 3.2.0 here.

    $18.99-$72.99 1

    SKU:BFESC3

    Weight: 0.10 kg

  • BetaflightF3 Flight Controller

    BetaflightF3 Flight Controller | REVIEW AND HOW TO by Joshua BardwellBetaflightF3 is the flight controller designed to use every possible feature of Betaflight. More than the last half year has been spent in development. Boris B has worked with us to go over features and design aspects to help give us insight into what betaflight users want/need. This board features a 3A power draw giving users extra room for added attachments through uart ports. The six layer PCB is a more expensive design approach but was needed to give the ability to have a PDB that was capable of having wiring pads on both the top and bottom of the board. By using the six layer design we were able to increase the size of the pads and work around all the components all the while giving esc connections in the corners of the board rather than bunching all connections on either the top OR the bottom. Featuring a fully functioning OSD that can be configured in Betaflight this board will make configuring your OSD a breeze. The team at betaflight have been hard at work developing DSHOT and this board is also compatible with the latest release. But we didn’t stop there, this board also features a micro adapter to accept TF cards for those of you that like to follow up your flights with reviewing black box logging...we think we know of at least one guy that will like that. FeaturesIntegrated PDBBuilt in OSD customizable via Betaflight OSDCurrent sensorIntuitive layoutSD card slot for BlackBoxTailored to support BetaflightWhen running 8K/8K, CPU usage remains lowSpecificationsF3 ProcessorMPU6000 Gyro/ACC SensorBEC Max current 5V 2ABuilt in OSD – configurable via Betaflight GUISD Card adapter for BlackBoxCurrent sensorPower distribution board with six-layer PCBOSD Max Current: 145AWeights 8.6g***Note: Please do not connect to any equipment with the loading over 1.5A.Friendly Reminder: Choosing your power supply for video is relatively simple. Betaflight FC has two options, 5v and battery voltage. Choose your camera voltage by jumping RAM with either the 5V solder section or the Vbat solder section. (its recommended to use Vbat, Most cameras and Video transmitters can run off battery voltage) If using 5v it is recommeded to only power your camera and get the power for Vtx from another source. 

    $42.99 3

    SKU:BFF3

    Weight: 0.10 kg




Find us on Google+ Watch us on Youtube Like us on Twitter Follow us on Facebook

Home   |   About Us   |   New Products   |   Multi-Rotors   |   FPV Airplanes   |   FPV Equipment   |   Battery / Chargers   |   Tools & Accessories   |   Contact Us   |   Blog   |  Site Map

Product Tags: ABCDEFGHIJKLMNOPQRSTUVWXYZ0-9

Copyright © 2015 FPVMODEL.COM®. All Rights Reserved.